Honeywell FocusPRO TH6110D User manual

Quick Reference Card
Grasp and pull to see basic
operating instructions at a
glance. \Battery Holder
Press down and pull to
remove batteries.
Batteries should be
replaced once a year
(see page 17).
_AUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage,
do not operate cooling system when outdoor temperature is below 50°F (10°C).
Read and save these instructions
® U.S.Registered Trademark. Patents pending.
Copyright O 2005 Honeywell International Inc. All rights reserved.

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
About your new thermostat
Thermostat features ........................ 2
Programming at a glance ................ 3
Quick reference to controls ............ 4
Quick reference to display .............. 5
Programming & Operation
Set time and day .............................. 6
Select fan setting (auto/on) ............ 7
Select system setting (heat/cool) ......8
Using program schedules ................ 9
Program schedule overrides ........ 12
Auto,changeover (heat/cool) ........ 14
Compressor protection ................ 15
Adaptive ]intelligent Recovery ''_.... 16
Appendices
Batte W installation ........................ 17
[n case of difficult), ...................... 18
Customer assistance ...................... 20
Accessories/replacement parts .... 20
Limited warrant)' .......................... 21
_CAUTION: EQUIPMENT DAMAGE
HAZARD. To prevent possible
compressor damage, do not operate
cooling system when outdoor
temperature is below 50°F (10°C).

Operating Manual
A _ $ I& $ _ _ $ _ I
Congratulations on the purchase of your new Honeywell thermostat. It has been
designed to give you many }rears of reliable service and easpto-use, push-button
climate control.
Festures
• Separately programn3able weekday/weekend schedules.
• One-touch temp control overrides program schedule at any time.
• EnergyStar '_compliant to greatly reduce your heating/cooling expenses.
• Large, clear, backlit displ W is easy to read -- even in the dark.
• Displays both room temperature and temperature setting.
• Removable battery holder [or fast, easy replacement.
• Built-in compressor protection.

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
Your new thermostat is pre-programmed and read?, to go.All you have to do is set
the time and day.Then check the settings below and change if needed:
1 Set time and day (required for proper operation) ................................ See page 6
2 Select fan setting (Auto/On): Preset to Auto ...................... To change, see page 7
3 Select system setting (Heat/Cool): Preset to Heat .............. To change, see page 8
4 Program schedules: Preset to energy-saving levels
while you're at work or asleep (assumes you
wake at 6 am, leave at 8 am, return at 6 pm
and go to bed at 10 pro) .............................................. To change, see pages 9-11
ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time,
and manually adjust the temperature (see pages 12-13).

Operating Manual
I
Battery holder (see page 17)
Temperature buttons
Press to adjust temperature
settings (see page 11-13)
Hold button
Press to override programmed
temperature control (see page 13)
Function buttons
Press to select the function displayed just above each button.
(Functions change depending on the task.)

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
| J
Current inside temperature Low battery warning Current time/day
Function buttons "
Press the button beneath each function to view or change
settings (functions change depending on the task)
_Heat (see 8)
page
Fan setting
Auto/On (see page 7)

Operating Manual
Press SETCLOCK/DA¥/SCHEaULEthen ust time ]
Press SETDAY,then select current day
Press the SETCLOCiO_DAY,/SCHEDULE
button, then press A or Y to set
the clock time.
2 Press the SETBAYbutton, then
press A or Y to select the day
of the week.
3 Press BONEto save & exit.
Note: If the SET CLBCKJDAY/SCHEBULE
option is not displayed, press BOREor
RUNSCHEDULE.
Note: if the display flashes Set Clock,
the thermostat will follow your settings
for the weekday "Wake" time period until
you reset the time and day.

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
Press the FANbutton to select Auto or On.
In "Auto" mode (the most commonly used
setting), the lhn runs only when the
heating or cooling system is on. If set to
"On," the fan runs continuously. Use this
setting [br improved air circulation, or [i)r
more efficient air cleaning.

Operating Manual
..... o I
Press the SYSTEM button to select:
Heat
Cool
Note: The Auto and Em Heat
system settings may not appear,
depending on how your
thermostat was installed,
, Heat:Thermostat controls only the
heating system.
•Cool: Thermostat controls only the
cooling system.
• Off'.Heath_g and cooling systems are off:
• Auto: Thermostat automatically selects
heating or cooling depending on the
indoor temperature.
• Em Heat (only [or heat pumps with
auxifiary heat):Thernaostat controls
Emergency and Auxiliary Heat.
Compressor is locked out.

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
!
It's easy to program your system [br maMmum energy savfl_gs.You can program lbur
time periods each day,with different settings lbr weekdays and weekends.
lg
I=
WAKE
6:06 am
=_a-3o
lU
LEAVE
8:00 am
0----Io
0£
RETURN
6:00 pm
"7#-lo
ILl
SLEEP
1O:00pm
_-- --io
OG
Set to the time you awaken and the temperature you want
during the morning, until you leave lk)r the day.
Set to the time you leave home and the temperature you
want while you are away (usually an energy-saving level).
Set to the time you return home and the temperature you
want during the evening, until bedtime.
Set to the time you go to bed and the temperature you want
overnight (usually an energy-saving leveb.

Operating Manual
• I
This thermostat is pre-set to use EnergyStar' prograln settings.We recolnmend
these setthlgs, since they can reduce }_)ur heating/cooling expenses by as much as
33% (See next page to adjust times and temperatures of each time period.)
WaRe
(6:00 am)
Leave
(8:00 am)
Return
(6:00pm)
SBeep
(10:00pm)
Heat (Men-FrO
-ll-a o
ILl
OC
-ll-a o
ILl
OC
Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun)
-_l-O -ll-ao=71-o
i-_ ill i Zo
j--l--lo
OD
-Tt-o
"_l--I° I- "-to "_l--lo
IO OtZ IO
10

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
1 Press SETCLOCK,/DAY/SCHEDULE,then SETSCHEDULE.
2 Press A or V to set your weekday Wake
thee (Mon-Fri), then press NEXT.
3 Press A or Y to set the temperature for
this time period, then press NEXT.
4 Set time and temperature for the next
tbne period (Leave). Repeat steps 2 and 3
_br each weekday time period.
5 Press NEXTto set weekend time periods
(Sat-Sun), then press DONEto save & exit.
Note: Make sure the thermostat is set to the
system you want to program (Heat or Cool).
Note: You can press CANCELPERIODto eliminate
unwanted time periods (except Wake).
11

OperatingManual
Press to temporarily adjust temperature Press Aor Y to immediately adjust the
temperature.This will temporarily override
the temperature setting for the current time
period.
The new temperature will be maintained
only until the next programmed time period
begins (see page 10). For example, if you
want to turn up the heat early in the
Pressto canceltemporarysetting morning, it will automatically be lowered
and resume program schedule later, when yOUleave R:)rthe day:
To cancel the tempera W setting at any time,
press RUNSCHEDULE.
Note: Make sure the thermostat is set
to the system you want to control
(heat, cool or auto).
12

FocosPROTM TH61 lOD/TH6220D Programmable Thermostat
Pressto permanently adjust temperature Press HOLDto peru-mnently adjust the
temperature.This will override tile
temperature settings for all time periods.
The "Hold" feature turns off the program
schedule and allows you to adjust the
thermostat manually, as needed.
Whatever temperature you set will be
maintained 24 hours a day, until you
Press to cancel "Hold" setting manually change it, or press RUNSCHEDULE
and resume program schedule to cancel "Hold" and resume the
programmed schedule.
Note: Make sure the thermostat is set
to the system you want to control
(heat, cool or auto).
13

OperatingManual
/
Auto
Auto Changeover is a feature used in
climates where both air conditioning and
heating are used on the same day:When the
system is set to Auto, the thermostat auto-
matically selects heating or cooling
depending on the indoor temperature.
Press until screen
displays "Auto"
Note: The Auto system setting
may not appear, depending on
how your thermostat was
installed.
Heat and cool settings must lye at least 3
degrees apart.The themaostat will automatically
adjust settings to mah_tain this 3-degree
separation (called "deadband").
The 3-degree separation between heating
and coolh_g set temperatures is fixed, and
cannot lye changed.
14

FocusPRO TM TH61 lOD/TH6220D Programmable Thermostat
This feature helps prevent damage to the
compressor in your air conditioning or heat
pmnp system.
Damage can occur if the compressor is re-
started too soon after shutdown.This feature
_i)rces tile compressor to wait [k:)ra few
minutes beti)re restarting.
J During the wait time, the display will flash
Message flashes until safe the message Cool On (or Heat On if you
restart time has elapsed have a heat pump).When the safe wait tin-m
has elapsed, the message stops flashing and
the COlnpressor turns on.
15

Operating Manual
A®.j - " o" "" o " A "I
Adaptive Intelligent Recove W eliminates guesswork when setting your schedule. It
allows the thermostat to "learn" how long your fi_rnace and air conditioner take to
reach the temperature you want.
Just set your program schedule to the time you want the house to reach your
desired temperature.The thermostat then turns on the heatH_g or cooling at just the
right time to reach your scheduled temperature at your scheduled trine.
For example: Set the Wake tH_aeto 6 am, and the temperature to 70°.The heat will
come on before 6 am, so the temperature is 70 ° by the time you wake at 6.
Note." When Adaptive intelligent Recovery is in effect, the thermostat
will display "In Recovery".
16

FocosPROTM TH61 lOD/TH6220D Programmable Thermostat
Press and pull to remove Batteries are optional (to provide backup
N power) your was run
if thelomostat wired to
on AC power when installed.
]install [}esh batteries immediately when the
REPLACE8A'rI"ER¥warning begins flashing.The
warning flashes about two months [)eft)re the
batteries are depleted.
Even if the warlmlg does not appear, you
InsertfreshAAalkaline should replace batteries once a year, or beR:)re
batteries, then reinstall leavh_g home R:)r more than a ll3onth.
batteryholder _ If batteries are hlserted within two mhmtes,
the time and day will not have to be reset.All
other settings are permanently stored h_
memow; and do not require batte W power.
17

Operating Manual
Ill you have difficulty with your thermostat, please try tile suggestions below. Most
problems can be corrected quickly and easily.
Display is blank * Check circuit breaker and reset if necessary.
, Make sure power switch at heating & cooling system is on.
, Make sure furnace door is closed securely.
• If thermostat is battery powered, make sure fresh AA alkaline batteries
are correctly installed (see page 17).
Temperature Make sure heating and cooling temperatures are set to acceptable ranges:
settings de not , Heat: 40° to 90°F (4.5 ° to 32°C).
change , Cool: 50° to 99°F (10 ° to 37°C).
To restore Follow these steps to restore Energy Star default settings (see page 10):
Energy Star _1Press SETCLOCK/DAY/SCHEDULE.
default settings 2 Press SETSCHEDULE.
3 Press DONEand NEXTat the same time for 4 seconds.
18