Hoover TurboPOWER FoldAway U5167900 User manual

HOOVER_
TurboPOWER"
FoldAway TM Upright
Thank you for
your purchase!
Owner's Manual
ENGLISH -I, pp. 1-12
ESPANOL -I, pag. 15-21
FRANGAIS -i, p. 22-28
www.hoover.com

Review this manual before
operating cleaner
Thank you fer cheosing a HOOVER®
PJease enter the COMPLETE model and serial numbers in the spaces provided.
The numbers are located on the bottom of your cJeaner.
Modem
Seda[ number
Hint: Attach your sames receipt to this owner's manual
Verification of date of purchase may be required for warranty service
of your HOOVER product.
Be sure to film out and return the product registration card included with your
cleaner (see back cover).
product,
HOOVER_CLEANER _
_2ev _oHz izoA v
a_LT _4_3a
Getting Started ...................................... 3
How to use ............................................ 4
Cleaner Description .......................... 4
Cleaning TooJs .................................. 6
If You Have aProbmem ........................ 11
Clearing B!ockages .................... 11o12
Important Safeguards .......................... 2
Maintenance
Authorized Service .......................... 1!
Cleaning FHters .............................. 7-8
Emptying Dirt Cup ............................ 7
Lubrication ...................................... 10
Replacing Agitator Brush Roll ...... 10
Replacing Be_t .............................. 9-10
Replacing Headlight .......................... 8
Therma_ Protector .............................. 10
Warranty .............................................. 12
© 2003 The Hoover Company
www.hoover.com
J! Safe
When using an e_ectrica{ appliance, a_ways follow
basic precautions, including the following:
READ ALL iNSTRUCTIONS BEFORE USING THiS APPLIANCE
m
m To reduce the risk of fire, electric shock, or injury:
Do not use outdoors or on wet surfaces.
Close supervision is necessary when any appliance is used by or near children.
Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.
Keep hair, Joose c_otbing, fingers, feet and all parts of body away from openings,
rotating agitator and other moving parts. Do not operate cleaner in bare feet or
when wearing open toe shoes or sandals.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or
hot ashes.
Do not use to pick up fiammabte or combustible matedats such as gasoline or fine
wood sandings or use in areas where they may be present.
Avoid picking up hard, sharp objects with the cleaner. They may damage the
cJeaner,
* Always turn off this appliance before connecting or disconnecting hose,
* Do not use without dirt cup or filters in place. Empty dirt cup and clean filters fre=
quent_y when picking up very fine materials such as powder.
Use extra care when cleaning on stairs.
Do not put any object into openings. Do not use with any opening b_ocked; keep
free of dust, _int, hair, or anything that may reduce air flow.
*Do not pull or carry by cord, use cord as a hand,e, dose door on cord or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away
from heated surfaces.
A_ways disconnect cord from eJectdca_ out_et before servicing the cleaner.
Unplug cleaner when not in use. Turn off aH controls before unplugging.
Do not unplug by pulling on cord. To unplug, grasp the p_ug, not the cord. Never
handle p_ug or appliance with wet hands.
The use of an extension cord is not recommended.
Do not use with damaged cord or plug. ff appliance is not working as it should, has
been dropped, damaged, _eft outdoors, or dropped into water, take it to a Hoover
Factory Service Center or Authorized Hoover Warranty Service Dea_er (Depot).
Use vacuum cleaner only for its intended use as described in the instructions.
Use only attachments recommended by The Hoover Company; others may cause
hazards.

If you need any assistance:
Visit our website at www.hoover.com. Click on the "Service" button
to find the service outlet nearest you OR
Call 1-800-944-9200 for an automated referral of service outlet
locations (U.S. only) OR
Call 1-330-499-9499 to speak with a representative in our Consumer
Response Center.
Please do not return this product to the store.
Carton contents
*Packed inside
extension wand
Your cleaner comes fully
assembled with the
tools and hose stored on
board.
Remove any tape or packing material
from the cleaner.
A. Cleaner
B. Hose, cleaning tools and wands
(packed on cleaner)
Using fold down handle
BLrJ
jc
Raise upper handle (A) to upright posi-
tion until it locks in place. Press upper handle release button (B) back to fold handle to storage position. Cord clip
To help keep the cord out of the way
while cleaning, position cord into cord
clip (C).
Continued -_ 3

Cleaner description
r.M
10
11
9
13
14--
18-----
12
Operate cleaner only at voltage specified on data
plate on bottom of cleaner.
This cleaner is intended for household use.
1. FoldAway TM handle
2. Upper handle release
button
3. Dirt cup handle/latch
4. Carrying handle
5. Dirt cup filter chamber
6. Pleated filter (inside filter
chamber)
7. Dirt cup
8. Headlight
9. Stair cleaning handle:
located under the
headlight.
10. Hood
11. Carpet height adjustment
knob: rotate knob to cor-
rect setting for height of
carpet being cleaned.
12. Handle release pedal:
step on pedal to lower
handle to operating or low
positions.
13. Hose
14. Furniture nozzle
15. Dusting brush
16. Extension wand
17. Crevice wand: stores
inside wand
18. Cord hooks: wrap
cord around hooks for
storage. The top hook
rotates to the left for
easy cord release.
19. ON/OFF switch: locat-
ed on left rear corner
of cleaner body
Polarized plug
Toreduce the risk of electric shock, this
appliance has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit,
contact a qualified electrician to install the
proper outlet. Do not change the plug in
any way.
ON-OFF switch
Plug cord into electrical outlet.
Toturn cleaner ON, push switch (A) toward
front of cleaner.
To turn cleaner OFF, push toward back of
cleaner.
Handle positions
The handle of your cleaner has three posi-
tions; upright when using cleaning tools;
operating position for general operation
on carpet and floors; low for reaching
under low furniture. Step on handle release
pedal to lower handle.

Transporting cleaner
Put handle in upright position. Tilt
cleaner back on rear wheels. Push
forward.
Carrying handle
Use the carrying handle to lift the
cleaner.
Carpet height
adjustment
The cleaning of carpet and rugs takes
place at the nozzle (B).
When it is necessary to raise and lower the
nozzle for various carpet pile heights, turn
the carpet height adjustment knob (C) to
the desired setting.
For ease in turning the knob, place handle
in upright position and tilt cleaner back
slightly.
Settings
For maximum cleaning performance,
tile following carpet height settings are
recommended.
• Low setting: for all types of carpet and
hard floors.
Note: Ifthe cleaner is difficult to push,
rotate knob to the next higher setting.
• Medium and High settings: for deeper
pile carpet where easier pushing effort is
desired, while maintaining good cleaning
performance.
{_iiJiiiii_¸
Cleaning lightweight
flexible rugs
Stand on one end of rug and move
cleaner toward other end or edge.
Before reaching edge, push down on
handle. This will lift up the nozzle (front
of cleaner) as shown and will prevent
rug from clinging to cleaner. Continue to
lift up nozzle so that when you have
reached the edge, it is completely off
the rug. Move cleaner back to start
again, lower nozzle, and use only for-
ward strokes.
Stair cleaning
A stair cleaning handle has been
designed for ease in using your cleaner
on stairs. With handle in operating posi-
tion, place fingers under edge of stair
cleaning handle and guide cleaner with
other hand on upper handle.
As an alternative, you may use the hose
and furniture nozzle for stair cleaning.
Clean from bottom to top.
When using cleaning tools, the agita-
tor will continue to rotate.
CAUTION: To avoid personal injury or
unnecessary wear to carpet, and to
prevent the cleaner from falling,
always place it at the bottom of the
stairs.
Continued -_ 5

Cleaning tools
Tools allow for cleaning surfaces above
the floor and for reaching hard to clean
areas.
The cleaner is ready for tool use when
handle is in upright position.
CAUTION: Agitator continues to
rotate while cleaner handle is in
upright position. Avoid tipping clean-
er or setting it on furniture, fringed
area rugs or carpeted stairs during
tool use.
E
G
)1
Select proper tool
D. Dusting brush may be used for
carved furniture, table tops, books,
lamps, lighting fixtures, venetian blinds,
baseboards, shutters, and registers.
E. Furniture nozzle may be used for
upholstered furniture, draperies, mat-
tresses, clothing, automobile interiors,
and carpeted stairs.
F. Crevice wand (stores inside exten-
sion wand) can be used in tight spaces,
corners and along edges in such places
as dresser drawers, upholstered furni-
ture, stairs and baseboards. It can also
be used for extra reach with the dusting
brush and/or extension wand.
G. Extension wand is used to give
extra length to your hose. Use it with any
of the above tools.
Remove hose
When using cleaning tools, cleaner
handle should be in the upright posi-
tion. Also, turn cleaner OFF before
disconnecting and connecting the
hose (H).
Remove hose end from cleaner base.
Attach wand and tools
The tools are attached to the hose or the
wand in the same manner.
Push tool firmly onto hose; twist tool slightly
to tighten or loosen connection.
Attach second wand or tool to the wand in
the same manner.
Replacing hose
When you are finished cleaning with the
tools, use the end of the hose to push
the cover (I) down and push hose onto
opening.
Twist hose end slightly to tighten the
connector.
Extra reach hose
The extra reach hose provides easier
cleaning of stairs and hard to reach
places. Follow the steps below for attach-
ing and detaching hose.
JK
Turn cleaner OFF before disconnecting
and connecting hose.
Remove hose end from cleaner base.
Align end of extra reach hose with projec-
tions (J) with slots (K) on end of attached
hose.
Slide hose into slots and twist hose to
lock it into place. (To detach hose,
reverse procedure.)
Attach wands or tools to the other end of
hose.
How to clean tools
To clean the hose, wipe off dirt with a
cloth dampened in a mild detergent.
Rinse with a damp cloth.
Cleaning tools may be washed in warm
water with a detergent. Rinse and air dry
before using.

Familiarizeyourselfwiththesehome
maintenancetasksasproperuseand
careofyourcleanerwillensurecontin-
uedcleaningeffectiveness.
Dirt cup
When to empty
It is recommended that the dirt cup be
emptied before the dirt reaches the dirt
opening on back of dirt cup (Fig. 4-2) or
after every use if preferred.
CAUTION: Very fine materials, such
as face powder or cornstarch, may
seal the filter and cause loss of suc-
tion. When using the cleaner for this
type of dust, empty the cup and clean
the filters often.
How to empty
Remove filter chamber (B) from dirt cup.
The dirt cup assembly consists of the
following parts:
Dirt cup (A)
Filter chamber (B)
Pleated filter (C)
Lid (D)
Dirt cup carry handle/latch (E)
Filter chamber release latch (F)
While the cleaner is in operation, the
screen at the bottom of the filter chamber
will stop larger debris from entering the
pleated filter chamber. This larger debris
will be seen collecting in the the dirt cup.
The pleated filter will collect fine particles
that have passed through the screen.
Disconnect cleaner from electrical
outlet. Do not use the cleaner without
dirt cup or filters in place.
Pull dirt cup handle (E) down. Remove
dirt cup.
Holding the carry handle (E), empty dirt
cup into wastebasket.
Filter assembly
How to clean filter
assembly
!;a
Press latch (F) on front of filter chamber
and remove lid. The pleated filter is
attached to the lid.
The screen (I) on the bottom of the
chamber can be cleaned with a soft
brush.
Empty filter chamber. Holding lid, tap bottom of filter against
edge of wastebasket until dust particles
stop falling from filter.
Do not tap the soft, pleated part of the
filter. It could damage the filter.
Do not rinse or wash the filter.
Continued -_ 7

Although not necessary, the filter can be
removed from the lid for cleaning.
Pull filter off lid and tap bottom of filter.
To replace, firmly press filter onto lid until
it stops.
Replace lid and filter on filter chamber.
Replace chamber on dirt cup.
Place bottom of cup behind tab (H) and
press cup into cleaner.
Rotate dirt cup handle (E) up to lock cup
in place.
Final filter
Cleaning final filter
The final filter assists in returning clean
air to the room.
Remove dirt cup.
Press latch (J) and remove filter grid.
Lift out filter (K) and hand wash in cold
water with a mild detergent.
Let filter air dry then reposition. Replace
filter grid and dirt cup.
Should you want to replace this filter, ask
for HOOVER part no. 38766008.
Do not operate cleaner without any of
the filters in place.
Headlight replacement
What to buy
This cleaner uses a 12 volt, wedge base
type 912 bulb, HOOVER part No.
27313107.
_5J_1
Disconnect cleaner from electrical
outlet.
Remove dirt cup as described in Fig.
3-2.
Insert a flat screwdriver into slot and
remove the access door (L).
Pull old bulb straight out of socket.
Push new bulb straight into socket until
locked in place.
Excessive force is not required.
\
Snap access door into place.
Reposition dirt cup (Fig. 3-10).

Belt replacement
The belt on your Hoover cleaner causes
the agitator to rotate and is important for
the effective operation of the cleaner.
The belt is located under the hood of the
cleaner and should be checked from
time to time to be sure it is in good con-
dition.
When to replace
Disconnect cleaner from electrical
outlet.
To check belt, remove hood and agitator
cover as shown in Figs. 3-16 through 3-
18. Replace belt if it is stretched, cut or
broken.
What to buy
To assure effective operation, use only
genuine HOOVER belts with your
cleaner. When purchasing a new belt,
ask for HOOVER part No. 40201190.
How to replace
Disconnect cleaner from electrical
outlet.
With the handle in the upright position,
tilt cleaner back until it rests on floor.
Remove the 2 screws near the front of
the brush roll cavity.
Press on handle release pedal (M) and
lower the nozzle so it is flat.
Remove hose end (Fig. 2-11 ).
Remove 2 screws at rear of hood.
Lift hood off cleaner. Remove the 2 screws behind the
agitator cover.
Remove agitator cover (N).
Remove agitator and used belt.
Discard used belt.
With lettering to the outside of belt, slide
new belt along side of cleaner cavity
and over motor pulley (0).
Insert agitator through belt and place
belt in belt guide (P).
,,R
Grasp agitator firmly and fit it into posi-
tion by first sliding end opposite the belt
into the rectangular slot (Q) on side of
cleaner.
Pull other side of agitator (R) into place.
Turn agitator, making sure belt is not
pinched between agitator and cleaner
body. The belt must rotate freely inside
the belt guide. If the agitator does not
turn, reposition belt in the belt guide.
Continued -_ 9

Replace agitator cover (N) and 2
screws. Replace hood, 2 screws and hose. Raise nozzle up and replace the 2 screws on the bottom.
The agitater brush roll
When te replace
When agitator brushes are worn, the
agitator should be replaced.
];o check condition of brushes, discon-
nect cleaner from electrical outlet.
Move edge of a card across bottom
plate while turning agitator. To maintain
cleaning effectiveness, replace agitator
if brushes do not touch card.
What to buy
When purchasing a new agitator, ask for
HOOVER part no. 48414110.
How to replace
Disconnect cleaner from electrical
outlet.
Remove hood and agitator cover as
described in the "Belt replacement"
section.
Discard old agitator.
Continue following the directions in the
"Belt replacement" section to replace
belt, new agitator, agitator cover and
hood.
The motor is equipped with bearings
that contain sufficient lubrication for the
life of the motor. The addition of lubricant
could cause damage. Therefore, do
not add lubricant to motor bearings.
The agitator brush roll is equipped with
two ball bearings that should be lubd=
cated periodically by a Hoover Factory
Service Center or an Authorized Hoover
Warranty Service Dealer (Depot).
Thermal protector
An internal thermal protector has been
designed into your cleaner to protect it
from overheating=
When the thermal protector activates,
the cleaner will stop running. If this
happens, proceed as follows:
I. Turn the cleaner OFF and distort=
nect it from the electrical outlet.
2=Check filters for dirt accumulation.
3=Refer to "Clearing blockages"
section.
4. When cleaner is unplugged and
the motor sools for 30 minutes, the
thermal protector automatically resets
and cleaning may continue.
If the thermal protector continues to
activate after following the above steps,
your cleaner may need servicing
(see"Service" section).
10