Horizon hobby Los05013 User manual

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in dam-

age to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and

responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with

incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and mainte-

nance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon

Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM

or Spektrum technology.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC.

For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

Your new Horizon Hobby vehicle has been designed and built with a combination of

waterproof and water-resistant components to allow you to operate the product in many

“wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your

vehicle should NOT be treated like a submarine. The various electronic components used in the

vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, how-

ever, most of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts

in the electrical cables, will be susceptible to corrosion if additional maintenance is not

performed after running in wet conditions. To maximize the long-term performance of your

vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions

Maintenance” section below must be performed regularly if you choose to run in wet

conditions. If you are not willing to perform the additional care and maintenance

required, then you should not operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and

complying with the following precautions could result in product malfunction

and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you

have all the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before

use. Caution should be taken when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s manual or the

manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean

water or water on salt-covered roads), contaminated or polluted water. Salt water

is very conductive and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certiﬁed

as water-resistant or waterproof. If the motor becomes excessively wet, apply very light

throttle until the water is mostly removed from the motor. Running a wet motor at high

speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of

operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or

larger spur gear. This will increase torque (and motor life) when running in mud, deeper

puddles, or any wet conditions that will increase the load on the motor for an extended

period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the

body removed, place the vehicle upside down and pull full throttle for a few short bursts

until the water has been removed.

CAUTION: Always keep hands, ﬁngers, tools and any loose or hanging objects

away from rotating parts when performing the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can

of compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a

garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove

any water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing

light oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue

to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings

with lightweight motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

As the user of this product, you are solely responsible for operating in a manner that does not

endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside

your control. This interference can cause momentary loss of control, so it is advisable to

always keep a safe distance in all directions around your model as this margin will help avoid

collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor,

electronic speed control and battery, because they generate high temperatures. You may

burn yourself seriously touching them.

• Do not put ﬁngers or any objects inside rotating and moving parts, as this may cause

damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car.Always turn off

the receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio

equipment.

SAFETY PRECAUTIONS AND WARNINGS

2SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

BOX CONTENTS

QUICK START

Please read the entire manual to gain a full understanding of the Baja Rey vehicle, ﬁne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings

and instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline

or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to

initialize. Always power the transmitter ON before the vehicle and power it OFF

after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos

are moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

• Losi®Super Baja Rey®RTR with AVC®Technology: 1/6-Scale 4WD Desert Truck (LOS05013)

• Spektrum™ DX2E 2.4GHz Transmitter (SPM2335)

• Spektrum™ 6-Channel DSMR®AVC2 Surface Receiver (SPMSRS6000)

• Spektrum™18KG Waterproof 1/5-Scale Servo (SPMS904)

• Dynamite®Fuze™ 160A BL WP 1/5-Scale ESC: 8S (DYNS2661)

• Dynamite®Fuze™ Brushless Motor 1200Kv (DYNS1660)

• 4 AA batteries (for transmitter)

TABLE OF CONTENTS

SAFETY PRECAUTIONS AND WARNINGS................................................................2

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS.........................2

QUICK START.............................................................................................................3

CHARGING THE BATTERY.........................................................................................3

BOX CONTENTS.........................................................................................................3

SPEKTRUM DX2E ACTIVE RADIO SYSTEM..............................................................4

SRS6000 AVC TECHNOLOGY RECEIVER ................................................................4

AUX CHANNELS...................................................................................................4

INSTALLING THE TRANSMITTER BATTERIES...........................................................4

SRS6000 STABILITY ASSIST RECEIVER....................................................................4

BINDING/CALIBRATING THE RECEIVER ..................................................................5

DISABLING AVC TECHNOLOGY................................................................................5

INSTALLING THE BATTERY........................................................................................5

DRIVING PRECAUTIONS...........................................................................................6

BEFORE RUNNING YOUR VEHICLE ..........................................................................6

POWERING ON THE VEHICLE ...................................................................................6

PERFORMING A CONTROL DIRECTION TEST..........................................................6

CHANGING THE TRAVEL ADJUST SETTINGS...........................................................6

RUN TIME...................................................................................................................7

POWERING OFF THE VEHICLE..................................................................................7

DYNAMITE FUZE 1200KV BRUSHLESS MOTOR......................................................7

ESC FUNCTIONS........................................................................................................8

TROUBLESHOOTING GUIDE .....................................................................................9

LIMITED WARRANTY ................................................................................................9

WARRANTY AND SERVICE CONTACT INFORMATION ..........................................10

FCC INFORMATION............................................................................................10

IC INFORMATION...............................................................................................10

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION................................10

REPLACEMENT PARTS ......................................................................................37–38

OPTIONAL PARTS....................................................................................................39

EXPLODED VIEWS.............................................................................................39–43

Choose batteries designed to work with the Dynamite®Fuze™ 160A Brushless Waterproof

ESC. We recommend standard LiPo batteries: the Dynamite®7.4V 5000mAh 2S 50C LiPo:

Hardcase with EC5™ connector (DYNB3810EC) or the Dynamite®11.1V 5000mAh 3S 50C

LiPo: Hardcase with EC5™ connector (DYNB3811EC) -or- HV LiPo batteries: the Dynamite®

7.6V 5000mAh 2S 50C LiPo: Hardcase with EC5™ connector (DYNB3855EC) or the

Dynamite®11.4V 5000mAh 3S 50C LiPo: Hardcase with EC5™ connector (DYNB3856EC).

Choose a charger designed to charge Li-Po batteries. We recommend the Dynamite®

Passport Duo 400W Dual AC/DC Touch Charger (DYNC3005) or the Dynamite®Passport

Ultra 100W AC/DC Touch Charger (DYNC3000). Refer to your battery and charger manuals

for usage, safety, and charging information.

CHARGING THE BATTERY

updates and more. Click on the Support tab at WWW.LOSI.COM and follow the product

registration link to stay connected.

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

567810 11

9 12 13

INSTALLING THE TRANSMITTER BATTERIES

1. Push in the battery cover a small amount to release the retaining tab, then remove the cover.

2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in the

transmitter’s battery case.

3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.

CAUTION: If using rechargeable batteries, charge only rechargeable batteries.

Charging non-rechargeable batteries may cause the batteries to burst, resulting in

injury to persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of

used batteries according to national regulations.

For more information on the transmitter, go to www.horizonhobby.com and click

on the support tab for the Spektrum DX2E to download the instruction manual.

SRS6000 AVC TECHNOLOGY RECEIVER

Antenna

Bind/Battery

Aux 4/Disable

Aux 3

Aux 2

Aux 1

Throttle

Steering

AUX CHANNELS

The Aux channels can operate as additional servo channels, or as a power supply for a personal

transponder.

If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational. The

remaining Aux channels can be used to power a personal transponder or lights.

If AVC is disabled (see DISABLING THE STABILITY ASSIST FUNCTION), all 6 channels (including

the Aux channels can operate as servo channels).

SPEKTRUM DX2E ACTIVE RADIO SYSTEM

1. Steering Wheel Controls direction (left/right) of the model

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. BIND Button Puts the transmitter into Bind Mode

4. ON/OFF Switch Turns the power ON/OFF for the transmitter

5. TH REV Reverses function of the speed control when pulled back or pushed forward

6. Indicator Lights

-Solid green light—indicates adequate battery power

-Flashing green light—indicates the battery voltage is critically low. Replace batteries

7. ST REV Reverses the function of the steering when the wheels is turned left or right

8. ST Trim Adjusts the steering center point

9. TH Trim Adjusts the throttle neutral point

10. TH Limiter Limits throttle output to 50, 70 or 100%.

11. 3-Position Switch Used to control a third channel and is preset at -100%/Neutral/100%

12. ST Rate Adjusts the sensitivity of AVC technology

13. Antenna Transmits the signal to the model

ACTIVE VEHICLE CONTROL™ (AVC®)

The Spektrum receiver features Active Vehicle Control™(AVC®) technology that responds

similar to traction control in full-scale vehicles. In addition to traction control,AVC technology

also increases steering stability during high speed driving or while driving over rough terrain.

As you increase the AVC sensitivity, the system increases steering stability and traction control,

similar to reducing the amount of steering rate in a computer transmitter. Reducing the

sensitivity value increases the amount of steering control from the transmitter.The receiver

also enables you to quickly turn AVC on or off if you participate in organized racing.

IMPORTANT: You must use digital servos with the AVC receiver. Do not use analog servos as

they willl reduce the performance of the system and may cause overheating.

AVC®SENSITIVITY

The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the

sensitivity, the AVC®system becomes more sensitive to the vehicle drifting left or right.You

would use maximum sensitivity during high speed driving or drag racing, when you want

the vehicle to stay in a straight line. As the sensitivity value increases, the amount of steering

travel decreases.

Turn the AVC/ST RATE knob counter-clockwise to reduce the

sensitivity.

Turn the AVC/ST RATE knob clockwise to increase the sensitivity

IMPORTANT: The ST RATE knob will only adjust the sensitivity

when the transmitter is bound to a DSMR®AVC® receiver. When the

transmitter is bound to a DSM2®/DSMR non AVC receiver, the ST

RATE knob controls the steering dual rate.

SRS6000 STABILITY ASSIST RECEIVER

4SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

BINDING/CALIBRATING THE RECEIVER

BINDING

Binding is the process of programming the receiver to recognize the GUID (Globally Unique

Identiﬁer) code of a single speciﬁc transmitter. When areceiver is bound to atransmitter/

model memory, the receiver will only respond to that speciﬁc transmitter/model memory.

Your Spektrum DX2E transmitter comes prebound to the vehicle. If you need to

rebind or calibrate, follow the instructions below.

1. With the vehicle on a ﬂat, level surface, insert the Bind Plug in the BIND port on the receiver.

2. Connect a fully charged battery pack to the ESC.

3. Power on the ESC.The orange LED ﬂashes on the receiver, indicating it is in bind mode.

4. Center the ST TRIM and TH TRIM dials on the transmitter.

5. Press and hold the BIND button while powering on the transmitter.

6. Release the BIND button when the orange LED slowly ﬂashes. The transmitter and

receiver are linked when the orange LED is solid.

CALIBRATING (continue from step 6 above)

7. Pull the transmitter trigger to Full Throttle, the orange LED will ﬂash once.

8. Push the transmitter trigger to Full Brake, then return the trigger to center.

9. Turn the transmitter steering wheel to Full Right. The orange LED ﬂashes.

10. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.

The orange LED ﬂashes once.

11. Remove the Bind Plug, then power off the receiver to save the settings.

12. Power off the transmitter.

DISABLING AVC®TECHNOLOGY

If you participate in organized racing, you may be required to turn AVC off. To turn AVC off:

1. Insert a Bind Plug in the BIND port on the receiver.

2. Insert a second Bing Plug in the DISABLE port on the receiver.

3. Connect a fully charged battery pack to the ESC.

4. Power on the ESC.The orange LED ﬂashes, indicating the receiver is in bind mode.

5. Center the ST TRIM and TH TRIM dials on the transmitter.

6. Press and hold the BIND button while powering on the transmitter.

7. Release the BIND button when the orange LED slowly ﬂashes.

The transmitter and receiver are linked when the orange LED is solid.

8. Pull the transmitter trigger to Full Throttle.

9. Push the transmitter trigger to Full Brake, then return the trigger to center.

10. Turn the transmitter steering wheel to Full Right.

11. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.

The orange LED ﬂashes once.

12. Remove the Bind Plugs, then power off the receiver to save the settings.

The receiver will continuously blink to indicate AVC is disabled.

13. Power off the transmitter.

IMPORTANT: You must calibrate the receiver each time it is placed in bind mode.

To activate AVC, see the steps in "Calibrating the Receiver."

FORWARD

BRAKE/REVERSE

LEFT/RIGHT

INSTALLING THE BATTERIES

1. Ensure the ESC is powered OFF.

2. Slide the button to the right to release the battery door.

3. Install the fully charged batteries in the vehicle.

4. Connect the batteries to the ESC.

5. Close the battery door and slide the battery door button to the left to secure it.

6. Power ON the transmitter, then the vehicle.

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the

vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move

forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.

When moving forward, the wheels should maintain a straight line without any steering wheel

input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to

turn the steering wheel.

CHANGING THE TRAVEL ADJUST SETTINGS

1. Hold the trigger in the full brake position and turn the steering wheel to Full Right while

powering on the transmitter. The LED ﬂashes rapidly, indicating the programming mode is

active.

2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust

the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position.Turn the TH TRIM knob

to adjust the full brake end point. Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left position.Turn

the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full right position.Turn the ST

TRIM knob to adjust the right end point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings.

The minimum Travel is 75%, and the Maximum travel is 150%.

IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate

the receiver.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Connect the fully charged battery packs to the ESC.

4. Power on the ESC.

IMPORTANT: The vehicle MUST remain on a ﬂat, level surface and motionless for

at least 5 seconds.

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle

off-road can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when

the battery is discharged can cause the receiver to power off. If the receiver loses power,

you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is

not covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries dis-

charged to a voltage lower than the lowest approved voltage may become dam-

aged, resulting in loss of performance and potential ﬁre when batteries are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck.

Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

BEFORE RUNNING YOUR VEHICLE

1. Check for free suspension movement. All suspension arms and steering components

should move freely. Any binds will cause the vehicle to handle poorly.

2. Charge a battery pack. Always charge the battery pack as per the battery and/or

charger manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim

so that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

6SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating

increases the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed.

The battery connectors may become hot during driving. Batteries will lose performance

and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries

and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airﬂow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

Your vehicle has been equipped with the optimal gearing for the stock platform. It offers an

ideal balance between speed, power and efﬁciency. Should you decide to customize your

vehicle with optional batteries or motors, it may be necessary for you to change the pinion or

spur gear.

Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater

torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with

fewer teeth will reduce torque and increase top speed. Care should be taken when installing

larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor

and ESC. When testing different gearing options, pay close attention to the temperature of

the motor and speed control to ensure you are operating within the temperature range of the

components. The motor or ESC should never be so hot that it cannot be touched. If tempera-

tures are too hot, a different gearing combination with a lower pinion gear and/or higher spur

gear is suggested.

CHANGING THE PINION GEAR/GEAR RATIO

The Super Baja Rey uses a motor mount with pre-set gearing from 16-24T.

1. Remove the lower motor mount chassis plate, the motor, and motor mount.

2. Loosen the set screw and remove the installed pinion gear.

3. Install the motor screws corresponding to the number of teeth on the pinion gear.

4. Place the new pinion gear on the end of the motor shaft, so the setscrew is located over

the ﬂat of the shaft.

5. Position the pinion gear so that the teeth line up with the spur gear and secure the pinion

gear by tightening the set screw.

6. Check the gear mesh to ensure that everything spins properly.

DYNAMITE®FUZE™ 1200KV BRUSHLESS MOTOR

SETTING THE GEAR MESH

The motor gearing is set on the motor mount and uses corresponding holes that match the

number of teeth on the pinion gear. The gear mesh has already been set at the factory. Setting

it is only necessary when changing motors or gears.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When

the gear mesh is too loose, the pinion gear can damage the spur gear. If the mesh is too tight,

speed could be limited and the motor and ESC will overheat.

IMPORTANT: The included 19T pinion gear is suitable for use with a 6S Li-Po battery.

NOTICE: For extreme load surfaces (e.g., sand and tall grass), gear down 1–2 teeth

on the pinion gear to minimize the chance of motor and ESC damage.

POWERING OFF THE VEHICLE

1. Power off the ESC.

2. Power off the transmitter.

3. Remove and charge the batteries.

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

SPECIFICATIONS

Type Sensorless

Constant/Peak 160A/1050A

Resistance 0.0002Ohm

Function Forward with Brake, Forward/Reverse with Brake

Operation Proportional forward, proportional reverse with braking

Input Voltage 3–8s LiPo

BEC Output 6V/8.4V, 6A

Overload Protection

Motor Lock-up protection, Low-voltage cutoff protection,

Thermal protection, Overload protection and fail safe (throttle

signal loss protection)

Dimensions (LxWxH) 70mm x 65mm x 45.5mm

Weight 288g

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.

• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage: The ESC checks the input voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause

(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that

the battery power is not too low for safe operation.

2. Radio Connection: The ESC checks radio signal input when it is powered ON.

If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause

(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

ESC FUNCTIONS

ESC CALIBRATION PROCEDURE

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.

1. Power OFF the ESC.

2. Ensure your transmitter is powered ON, the throttle is not reversed, the

throttle trim is neutral and the throttle travel range is at 100%. Disable

any special functions such as ABS, etc.

3. Press the SET button while powering ON the ESC. Release the button as soon as the red

LED starts to ﬂash.

4. Calibrate the throttle points by pressing the SET button once after each step.

- Neutral (1 ﬂash)—leave the throttle at rest, untouched

- Full throttle (2 ﬂashes)—pull the throttle fully back

- Full brake/reverse (3 ﬂashes)—push the throttle fully forward

5. The motor will run 3 seconds after the last step is completed.

Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside

motor wires. The center wire must remain in the center and cannot be moved to another

motor tab.

ESC PROGRAMMING PROCEDURE

1. Connect a fully charged battery to the ESC.

2. Power ON the ESC using the ESC switch.

3. Hold the SET button for 1 second until the GREEN LED blinks, then release the SET button

to enter programming mode.

4. Press and release the SET button as needed to get to the desired menu option (the GREEN

LED will blink corresponding to the menu item number). Programming menu items 1

through 6 are accessible using the SET button on the ESC.

5. When at the desired menu item, hold the SET button for 3 seconds until the RED LED blinks.

6. Press the SET button to move among the settings based on how many times the RED LED

blinks (Refer to the table for more information).

7. Save the setting by holding the SET button for 3 seconds.

8. Power OFF the ESC switch and repeat the instructions above to change other settings.

DESCRIPTIONS

1. Running Mode

-Forward Only with Brake

Intended for competition use, this mode allows only forward and brake controls.

-Forward/Reverse with Brake

This mode is the basic all-around mode, allowing forward, reverse and brake controls.

To engage reverse while moving forward, apply the brake until the vehicle has come to

a complete stop, release brake, then apply the brake again.While braking or in reverse,

engaging the throttle will result in the vehicle immediately accelerating forward.

2. Li-Po Cells

The default setting is Auto Calc, which will automatically select the detetected number

of cells. Select value 2–5 to manually select a cell count from 3–8 cells.

3. Low Voltage Cutoff

This function helps to prevent battery over-discharge. The ESC continuously monitors the

battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output

power shuts off and the red LED ﬂashes twice repeatedly.

The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,

if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery

pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a

8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po

battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).

4. Bec Voltage

Select either 6 or 8.4 V to run the receiver and servos.

5. Max Brake Force

Adjusts the maximum braking force. A higher value provides stronger braking, but can

also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force

This parameter adjusts the maximum power when travelling in reverse.

7. Start Mode (Punch)

Sets the initial throttle punch when the car accelerates. Level 1 gives a very soft initial

acceleration and level 5 gives a stronger initial acceleration.

8. Timing

Allows for timing value selection according to your motor. Generally, higher timing value

brings out higher power output, but the efﬁciency of the system will be slightly lower with

possible increases in motor and ESC running temperatures.

ENEN

The black-shaded setting is the factory default.

PROGRAMMABLE ITEMS

PROGRAMMABLE VALUE

1 2 3 4 5 6 7 8 9

1 Running Mode Forward with Brake Forward/ Reverse with Brake

2 Li-Po Cells Auto Calc. 3s 4s 6s 8s

3 Low Voltage Cutoff Auto (Low) Auto (Intermediate) Auto (High)

4 BEC Voltage 6.0V 8.4V

5 Max Brake Force 25% 50% 75% 100% Disable

6 Max Reverse Force 25% 50%

7 Start Mode/Punch Level 1 Level 2 Level 3 Level 4 Level 5

8 Timing 0° 3.75° 7.5° 11.25° 15°

8SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate

Battery not charged or plugged in Charge battery/plug in

ESC switch not “On” Turn on ESC switch

Transmitter not “On” or low battery Turn on/replace batteries

Motor runs but wheels

do not rotate

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft ﬂat spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Steering does not work Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity

Servo gears or motor damaged Replace or repair servo

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run

Motor wires not connected properly Check bullet connectors for proper ﬁt

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

ESC gets hot Motor over-geared Use smaller pinion or larger spur gear

Driveline bound up Check wheels and transmission for binding

Poor run time and/or sluggish

acceleration

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Poor range and/or glitching

Transmitter batteries low Check and replace

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the

“Product”) will be free from defects in materials and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due

to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,

installation, operation or maintenance, (iii) modiﬁcation of or to any part of the Product, (iv)

attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product

not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable

technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY

OR REPRESENTATION,AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon

will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be

defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty

claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase

is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,

REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability

of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be

assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,

the user accepts all resulting liability. If you as the purchaser or user are not prepared to

accept the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂict of law principals). This

warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state

to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service.

Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions or assistance, please

visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll

free telephone number referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live

and use the Product in, please use the Horizon Online Service Request submission process

found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)

number. Pack the Product securely using a shipping carton. Please note that original boxes

may be included, but are not designed to withstand the rigors of shipping without additional

protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,

as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.

An Online Service Request is available at http://www.horizonhobby.com/content/_service-

center_render-service-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your product

for service. When calling Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included

items, and a brief summary of the problem.A copy of your original sales receipt must be

included for warranty consideration. Be sure your name, address, and RMA number are clearly

written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a

Li-Po battery, please contact the appropriate Horizon Product Support ofﬁce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying

the proof-of-purchase date. Provided warranty conditions have been met, your Product

will be serviced or replaced free of charge. Service or replacement decisions are at the sole

discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and

payment will be required without notiﬁcation or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notiﬁcation. Service estimates are

available upon request.You must include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you

will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as

Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for

service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of

use and ownership. If received, a non-compliant Product will not be serviced.

Further, the sender will be responsible for arranging return shipment of

the un-serviced Product, through a carrier of the sender’s choice and at the

sender’s expense. Horizon will hold non-compliant Product for a period of 60

days from notiﬁcation, after which it will be discarded.

10/15

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/

4105 Filedstone Rd.

Champaign, Illinois 61822 USA

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales websales@horizonhobby.com

800-338-4639

EU Horizon Technischer Service service@horizonhobby.eu

+49 (0) 4121 2655 100

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

Warranty and Service Contact Information

EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product

is in compliance with the essential requirements and other relevant provisions of the

RED and EMC Directives.

A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the

European Union

This product must not be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by handing it over to a designated

collections point for the recycling of waste electrical and electronic equipment. The separate

collection and recycling of your waste equipment at the time of disposal will help to conserve

natural resources and ensure that it is recycled in a manner that protects human health and

the environment. For more information about where you can drop off your waste equipment for

recycling, please contact your local city ofﬁce, your household waste disposal service or where you

purchased the product.

10 SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • INSTRUCTION MANUAL

FCC Statement

FCC ID: BRWDX2EQ2UC | BRWDASRX12 This device complies with part 15 of the FCC

rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modiﬁcations not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and

found to be compliant with the applicable regulations governing a radio transmitter in the

2.400GHz to 2.4835GHz frequency range.

This equipment has been tested and found to comply with the limits for Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

IC Information

IC: 6157A-DX2EQ2UC | 6157A-AMRX12 This device complies with Industry Canada

licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Antenna Separation Distance

When operating your Spektrum

transmitter, please be sure to

maintain a separation distance of

at least 5 cm between your body

(excluding fingers, hands, wrists,

ankles and feet) and the antenna

to meet RF exposure safety

requirements as determined by

FCC regulations.

The following illustrations show

the approximate 5 cm RF exposure

area and typical hand placement when operating your Spektrum transmitter.

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • MANUALE DI ISTRUZIONI

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

Part # English Deutsch Français Italiano

DYNS1660 Fuze 1/6th BL Motor 1200kv Fuze 1/6th BL Motor 1200kv Moteur Fuze 1200kV BL 4P 1/6 Motore Fuze 1/6 denti BL 1200Kv

DYNS2661 Fuze 160A BL WP 1/5th ESC Zünder 160A BL WP 1/5-Maßstab ESC ESC Fuze 160A BL WP 1/5 ESC Fuze 160A BL WP 1/5 denti

LOS235007 Button Head Screw M3 x 12 mm (10) Rundkopfschraube, M3 x 12 mm (10) Vis à tête bombée, M3 x 12mm (10) Vite a testa tonda M3 x 12 mm (10)

LOS235009 Flat Head Screw M2.5 x 8 mm (10) Flachkopfschraube M2,5 x 8 mm (10) Vis à tête plate, M2.5 x 8mm (10) Vite a testa piana M2.5 x 8 mm (10)

LOS235012 Set Screw M4 x 4 mm Cup Point (10) Stellschraube, M4 x 4mm Ringschneide (10) Vis de ﬁxation, bout civette, M4 x 4mm (10) Vite di fermo M4 x 4 mm punta a tazza (10)

LOS235025 Button Head Screw M3 x 30 mm (10) Rundkopfschraube, M3 x 30 mm (10) Vis à tête bombée, M3 x 30 mm (10) Vite a testa tonda M3 x 30 mm (10)

LOS236001 3.2 mm x 7 mm x .5 mm Washer (10) 3,2 mm x 7mm x 0,5 mm Unterlegscheibe (10) Rondelle 3,2mm x 7mm x 5mm (10) Rondella 3,2 mm x 7 mm x 0,5 mm (10)

LOS250022 Body Button Base and Top (22) Body Button unten und oben (22) Bouton corps haut et bas (22) Base e parte superiore bottone carrozzeria (22)

LOS250023 Interior Set w/ Helmets,Clear Interieurset mit Helmen,Transparent Lot intérieur avec casques, clair Serie interni con caschi, trasparente

LOS250024 Brake and Spare Tire Accessory Set Bremse und Ersatzreifen Zubehörset Ensemble d’accessoires pour pneus de secours et freins Serie accessori freno e pneumatico di riserva

LOS250025 Cab Section, Black Baldachinabschnitt, Schwarz Section cabine, noir Sezione abitacolo, nera

LOS250026 Front Hood, Black Frontklappe, Schwarz Capot avant, noir Cofano anteriore, nero

LOS250027 L/R Rear Fender Set,Black L/R Heck Schutzblechset, Schwarz Lot de protections arrières D/G, noir Serie parafanghi anteriori sinistro/destro, neri

LOS250028 Front Hood, Red Frontklappe, Rot Capot avant, rouge Cofano anteriore, rosso

LOS250029 L/R Rear Fender Set,Red L/R Heck Schutzblechset, Rot Lot de protections arrières D/G, rouge Serie parafanghi posteriori sinistro/destro, rossi

LOS250030 Cab Section, Red Baldachinabschnitt, Rot Section cabine, rouge Sezione abitacolo, rossa

LOS251054 Roll Cage Sides (L&R) Überrollkäﬁgseiten (L&R) Cage de retournement, côtés, D/G Lati scocca di protezione (Sinistro e destro)

LOS251055 Rear Body Mount Bar (L&R) X-Bar Hintere Gehäusehalterungsstange (L&R) X-Balken Crossbar, barre de montage (G/D), corps arrière Barra supporto carrozzeria posteriore (Sinistra e destra),

Barra Trasversale

LOS251056 Rear Bulkhead, Fan Panel, Mud Guards Hintere Spritzwand, Lüfterplatte, Schmutzfänger Cloison arrière, panneau ventilation, garde-boue Paratia posteriore, pannello ventola, parafanghi

LOS251057 Front Bumper & Skid Plate Frontstoßstange und Gleitbrett Pare-choc avant et plaque de protection Paraurti anteriore e piastra protezione

LOS251058 Battery Tray, Door, Lock, EC5 Base Set Akkuhalterung, Tür, Schloss, EC5-Basis-Set Support de batterie, porte, verrou, ensemble de base EC5 Vassoio portabatterie, sportello, blocco, serie base EC5

LOS251059 Steering Servo Mount & Bellcrank Set Lenkservo-Halterung & Umlenkhebelset Support de servo de direction et ensemble levier Supporto servocomandi sterzo e serie leve a gomito

LOS251060 Rear Chassis Brace/ESC Mount Hintere Karosseriestrebe/

Geschwindigkeitsreglerhalterung

Renfort châssis arrière/support variateur ESC Sostegno anteriore telaio/Supporto ESC

LOS251061 Chassis & Motor Cover Plate Karosserie & Motorabdeckplatte Plaque de couvercle châssis et moteur Piastra copertura telaio e motore

LOS251062 Center Chassis Brace & Stand Offs Zentrale Karosseriestrebe & Standoffs Renfort châssis central et douilles Sostegno e supporti centrali telaio

LOS251063 LED Light Bar Front LED-Lichtstange Front Barre d’éclairage à DEL avant Barra anteriore luci LED

LOS251064 LED Light Bar Rear LED-Lichtstange Heck Barre d’éclairage à DEL arrière Barra posteriore luci LED

LOS251065 Steering Hardware Set Hardwaresatz Lenkung Ensemble de matériel de direction Set bulloneria sterzo

LOS251066 Steering Servo Arm, 15T Spline Servolenkarm, 15T Verzahnung Bras du servo de direction, cannelure 15T Braccio servocomandi sterzo, scanalatura 15 denti

LOS251067 Steering Tie Rods (2) Lenkung Zuganker (2) Biellettes de direction (2) Tiranti sterzo (2)

LOS251068 Foam Seal & Spacer Set Schaumdichtung & Distanzstückset Lot mousse d’étanchéité et entretoises Serie sigillanti in materiale espanso e spessori

LOS251069 Roll Cage Top Bar, Front Bar Obere Stange des Überrollkäﬁgs,Vorderstange Cage de retournement, barre supérieure, barre avant Barra superiore, barra anteriore scocca di protezione

LOS252039 Pinion Gear,16T, Mod 1.5 Zahnradgetriebe, 16T, Mod 1,5 Engrenage à pignons, 16R, 1,5M Ingranaggio pignone, 16 denti, mod. 1,5

LOS252040 Pinion Gear 17T, Mod 1.5 Zahnradgetriebe, 17T, Mod 1,5 Engrenage à pignons, 17T, 1,5M Ingranaggio pignone, 17 denti, mod. 1,5

LOS252041 Pinion Gear, 18T, Mod 1.5 Zahnradgetriebe, 18T, Mod 1,5 Engrenage à pignons, 18T, 1,5M Ingranaggio pignone, 18 denti, mod. 1,5

LOS252043 Pinion Gear, 20T, Mod 1.5 Zahnradgetriebe, 20T, Mod 1,5 Engrenage à pignons, 20T, 1,5M Ingranaggio pignone, 20 denti, mod. 1,5

LOS252044 Pinion Gear, 21T, Mod 1.5 Zahnradgetriebe, 21T, Mod 1,5 Engrenage à pignons, 21T, 1,5M Ingranaggio pignone, 21 denti, mod. 1,5

LOS252045 Pinion Gear, 22T, Mod 1.5 Zahnradgetriebe, 22T, Mod 1,5 Engrenage à pignons, 22T, 1,5M Ingranaggio pignone, 22 denti, mod. 1,5

LOS252069 Diff Housing & Gasket Differentialgetriebe-Gehäuse & Dichtung Boîtier différentiel et joint Alloggiamento e guarnizione differenziale

LOS252070 Differential Rebuild Kit Differentialgetriebe-Umbau-Kit Kit de reconstruction du différentiel Kit riparazione differenziale

LOS252071 Axle Housing Set, Rear Achsgehäuse-Set, Heck Lot de carte d’essieu, arrière Serie alloggiamento dell’assale,posteriore

LOS252072 Rear Driveshaft Set Heck Antriebswelle-Set Lot d’arbre d’entraînement arrière Serie posteriore albero di trasmissione

LOS252073 Center Transmission Housing Zentrales Getriebegehäuse Boîtier de transmission centrale Alloggiamento centrale trasmissione

LOS252074 Front Gear Box/Bulkhead Front Getriebekasten/Spritzwand Réducteur avant/Cloison Scatola del cambio anteriore/Paratia

LOS252075 38T Ring & 12T Pinion Gear FR/RR 38T Ring & 12T Zahnradgetriebe FR/RR Bague 38T et engrenage à pignons 12T AV/AR Anello 38 denti e ingranaggio pignone 12 denti FR/RR

LOS252076 Outdrive Set FR/RR (2) Antrieb-Set FR/RR (2) Ensemble sortie AV/AR (2) Serie gruppo di trasmissione FR/RR (2)

LOS252077 20 mm Wheel Hexes and Pins, Black (4) 20 mm Rad Sechskante und Bolzen, Schwarz (4) Hexagones de roue et broches 20mm, noir (4) Dadi esagonali e perni ruota 20 mm, neri (4)

LOS252078 Wheel Nut, Black (4) Radmutter, Schwarz (4) Écrou de roue, noir (4) Dado ruota, nero (4)

LOS252079 Pinion Gear, 19T, 1.5M, 8mm Shaft Zahnradgetriebe, 19T, 1,5M, 8mm Welle Engrenage à pignons, arbre de 19T, 1,5M, 8mm Pignone, 19 denti, 1,5M, albero da 8mm

LOS252080 Center Transmission Gear Set Zentrales Übersetzungsgetriebe-Set Lot de transmission centrale Serie centrale ingranaggi trasmissione

LOS252081 Stub Axle, Rear (2) Achswellenstumpf, Heck (2) Porte-fusée, arrière (2) Fusello di ruota, posteriore (2)

LOS252082 Dogbone,Rear Axle (2) Dogbones, Hinterachse (2) Cardans à boules goupillées, essieu arrière (2) Cardano spinato (dogbone), assale posteriore (2)

LOS252083 Motor Mount Motorhalterung Support moteur Supporto motore

LOS252084 Center Drive Shaft, Front Zentrales Antriebswelle, Front Arbre d’entraînement central, avant Albero di trasmissione centrale, anteriore

LOS252085 FrontAxle Set (2) Vorderachsenset (2) Lot d’essieu avant (2) Serie assali anteriori (2)

LOS252086 Diff Locker Differentialgetriebefach Verrouillage différentiel Dispositivo di blocco del differenziale

LOS252087 Center Diff Outdrive Set (2) Zentrales Differentialantrieb-Set (2) Lot de sortie de différentiel centrale (2) Serie gruppo di trasmissione centrale (2)

LOS254033 Shock Rebuild Kit (4) Stoßdämpfer-Umbau-Kit (4) Kit de reconstruction amortisseurs (4) Kit riparazione ammortizzatore (4)

LOS254034 Shock & Rod Ends,Spring Cups (12) Stoßdämpfer- und Gelenkköpfe, Federteller (12) Amortisseur et embouts de bielle,cuvettes de ressort (12) Ammortizzatore ed estremità aste, coppe a molla (12)

LOS254035 Shock Pistons Stoßdämpferkolben Pistons amortisseurs Pistoni ammortizzatori

LOS254036 Trailing Arms (2) Hinterachsträger (2) Bras oscillants (2) Bracci longitudinali (2)

LOS254037 Front SuspensionArm Set Upper/Lower (L&R) Front Querlenker-Set Oberer/Unterer (L&R) Bras de suspension avant conﬁguration élevée/basse (G/D) Serie braccetti sospensione anteriore Superiore/Inferiore

(sinistro e destro)

LOS254038 Front Spindle Set (L&R) Front Spindelsatz (L&R) Lot de fusées avant (G/D) Serie fuso anteriore (L&R)

SUPER BAJA REY®DESERT TRUCK: 1:6 4WD RTR, AVC

SUPER BAJA REY® DESERT TRUCK: 1:6 4WD RTR, AVC • MANUALE DI ISTRUZIONI

Part # English Deutsch Français Italiano

LOS254039 Upper Arm/Shock Mount, Front Oberer Arm/Stoßdämpferhalterung, Front Bras supérieur/support amortisseurs, avant Braccetto superiore/supporto ammortizzatore, anteriore

LOS254040 ShockTower, Upper/Lower Track Rod Mount Stoßdämpferbrücke, obere/untere

Spurstange-Halterung

Support d’amortisseurs,support tige de renfort élevé/bas Torre ammortizzatore, supporto asta tracciato superiore/

inferiore

LOS254041 Shock Body & Collar Set, Front (2) Stoßdämpfergehäuse & Hülsenset, Front (2) Corps antichoc et ensemble bagues,avant (2) Serie collare e corpo ammortizzatore, anteriore (2)

LOS254042 Shock Body & Collar Set, Rear (2) Stoßdämpfergehäuse & Hülsenset, Heck (2) Corps antichoc et ensemble bagues, arrière (2) Serie collare e corpo ammortizzatore, posteriore (2)

LOS254043 Front & Rear Sway Bar Set Front & Heck Schwingen-Set Lot de barre stabilisatrice avant et arrière Serie barre stabilizzatrici anteriore e posteriore

LOS254044 Shock Shaft, Front (2) Kolbenstange, Front (2) Butées de suspension avant (2) Albero ammortizzatore, anteriore (2)

LOS254045 Shock Shaft, Rear (2) Kolbenstange, Heck (2) Butées de suspension arrière (2) Albero ammortizzatore,posteriore (2)

LOS254046 Front Spring, Med, Silver (2) Frontfeder, Med, Silber (2) Ressort avant, moy, argent (2) Molla anteriore, media, argento (2)

LOS254047 Rear Spring, Med, Silver (2) Heckfeder, Med, Silber (2) Ressort arrière, moy, argent (2) Molla posteriore, media, argento (2)

LOS254048 Front Hinge Pin and Brace Set Front Scharnierstift und Klammersatz Lot d’axes de charnière avant Set piastrine e perni cerniere anteriore

LOS254049 Upper Trailing Arm Links (2) Oberer Flügelarmverbindung (2) Liaisons bras oscillant supérieur (2) Collegamenti bracci longitudinali superiori (2)

LOS254050 Shock Stand Off, Front (2) Stoßdämpfer-Standoff, Front (2) Butées de douilles, avant (2) Distanziatore ammortizzatore, anteriore (2)

LOS254051 Pivot Ball Set Schwenkkugel-Set Lot billes pivot Serie sfere perno

LOS254052 Hinge Pin Screw, Outer (4) Scharnierbolzenschraube, äußere (4) Vis de charnière, sortie (4) Vite perno cerniera, esterna (4)

LOS255009 Cap Head Screw, Stl, BO, M3 x 16 mm (10) Inbusschraube, Stl, BO, M3 x 16 mm (10) Vis d’assemblage creuse,stl, BO, M3 x 16mm (10) Vite a testa cilindrica, acciaio, BO, M3 x 16 mm (10)

LOS255011 Button Head Screw, Stl, BO, M4 x 30 mm (10) Rundkopfschraube, Stl, BO, M4 x 30 mm (10) Vis à tête bombée,stl, BO, M4 x 30mm (10) Vite a testa tonda, acciaio, BO, M4 x 30 mm (10)

LOS255012 Button Head Screw, Stl, BO, M4 x 35 mm (10) Rundkopfschraube, Stl, BO, M4 x 35 mm (10) Vis à tête bombée,stl, BO, M4 x 35mm (10) Vite a testa tonda, acciaio, BO, M4 x 35 mm (10)

LOS255013 Button Head Screw, Stl, BO, M4 x 65 mm (10) Rundkopfschraube, Stl, BO, M4 x 65 mm (10) Vis à tête bombée,stl, BO, M4 x 65mm (10) Vite a testa tonda, acciaio, BO, M4 x 65 mm (10)

LOS255014 Button Head Screw, Stl, BO, M4 x 14 mm (10) Rundkopfschraube, Stl, BO, M4 x 14 mm (10) Vis à tête bombée,stl, BO, M4 x 14mm (10) Vite a testa tonda, acciaio, BO, M4 x 14 mm (10)

LOS255016 Flat Head Screw, Stl, BO, M4 x 10 mm (10) Flachkopfschraube, Stl, BO, M4 x 10 mm (10) Vis à tête plate, stl,BO, M4 x 10mm (10) Vite a testa piana, acciaio, BO, M4 x 10 mm (10)

LOS255017 Flat Head Screw, Stl, BO, M4 x 16 mm (10) Flachkopfschraube, Stl, BO, M4 x 16 mm (10) Vis à tête plate, stl,BO, M4 x 16mm (10) Vite a testa piana, acciaio, BO, M4 x 16 mm (10)

LOS255018 Flat Head Screw, Stl, BO, M4 x 25 mm (10) Flachkopfschraube, Stl, BO, M4 x 25 mm (10) Vis à tête plate, stl,BO, M4 x 25mm (10) Vite a testa piana, acciaio, BO, M4 x 25 mm (10)

LOS255019 Flat Head Screw, Stl, BO, M4 x 14 mm (10) Flachkopfschraube, Stl, BO, M4 x 14 mm (10) Vis à tête plate, stl,BO, M4 x 14mm (10) Vite a testa piana, acciaio, BO, M4 x 14 mm (10)

LOS255020 Flat Head Screw, Stl, BO, M4 x 18 mm (10) Flachkopfschraube, Stl, BO, M4 x 18 mm (10) Vis à tête plate, stl,BO, M4 x 18mm (10) Vite a testa piana, acciaio, BO, M4 x 18 mm (10)

LOS255021 Set Screw, Stl, BO, Flat Point,M4 x 6 mm (10) Stellschraube, Stl, BO, Flat Point, M4 x 6 mm (10) Vis de ﬁxation, stl,BO, bout plat, M4 x 6mm (10) Vite di fermo, acciaio, BO, punta piana, M4 x 6 mm (10)

LOS255022 Set Screw, Stl, BO, Flat Point,M5 x 30 mm (10) Stellschraube, Stl, BO, Flat Point, M5 x 30 mm (10) Vis de ﬁxation, stl,BO, bout plat, M5 x 30mm (10) Vite di fermo, acciaio, BO, punta piana, M5 x 30 mm (10)

LOS255024 Flat Nut, Stl, M4 (10) Flache Mutter, Stl, M4 (10) Écrou plat, stl, M4 (10) Dado piano, acciaio, M4 (10)

LOS257006 10 x 19 x 5 mm Ball Bearing (2) 10 x 19x5 mm Kugellager (2) Roulement à billes 10 x 19 x 5mm (2) Cuscinetto a sfera 10 x 19 x 5 mm (2)

LOS257007 4 x 8 x 3mm Ball Bearing (4) 4 x 8x3mm Kugellager (4) Roulement à billes 4 x 8 x 3mm (4) Cuscinetto a sfera 4 x 8 x 3mm (4)

LOS45019 Desert Claw Tire with Foam (2) Desert Claw-Reifen mit Schaumstoff (2) Pneu DesertClaw avec mousse (2) Pneumatico Desert Claw con materiale espanso (2)

LOS45020 Wheels, Silver (2) Räder, Silber (2) Roues, argent (2) Ruote, argento (2)

LOSA6942 8 x 16 mm Sealed Ball Bearing (4) 8 x 16mm abgedichtetes Kugellager (4) Roulement à billes hermétique 8 x 16mm (4) Cuscinetto a sfera sigillato 8 x 16 mm (4)

SPM2335 DX2E Active 2-CH DSMR Radio w/ SR310 DX2E Aktives 2-Kanal DSMR Funkgerät mit SR310 Radio DX2EActive 2canaux DSMR avec SR310 Radiocomando DX2EActive 2 canali DSMR con SR310

SPMS904 S904 1/6 Scale WP Digital Servo S904 1/6 Maßstab WP Digitaler Servo Servo numérique WP à l’échelle 1/6 S904 Servocomando digitale S904 scala 1/6 WP

SPMSRS6000 SRS6000 DSMR AVC Surface Rx SRS6000 DSMR AVC Oberﬂächenempfänger SRS6000 DSMR AVC SurfaceRx Ricevitore di superﬁcie SRS6000 DSMR AVC

TLR255003 Cap Head Screw, M2.5 x 6 mm (10) Inbusschraube, M2,5 x 6 mm (10) Vis d’assemblage creuse, M2.5 x 6mm (10) Vite a testa cilindrica M2.5 x 6 mm (10)

TLR255008 Button Head Screw, M4 x 16 mm (10) Rundkopfschraube, M4 x 16 mm (10) Vis à tête bombée, M4 x 16mm (10) Vite a testa tonda M4 x 16 mm (10)

TLR255009 Button Head Screw, M4 x 20 mm (10) Rundkopfschraube, M4 x 20 mm (10) Vis à tête bombée, M4 x 20mm (10) Vite a testa tonda M4 x 20 mm (10)

TLR255010 Button Head Screw, M4 x 25 mm (10) Rundkopfschraube, M4 x 25 mm (10) Vis à tête bombée, M4 x 25mm (10) Vite a testa tonda M4 x 25 mm (10)

TLR255013 Flat Head Screw, M4 x 12 mm (10) Rundkopfschraube, M4 x 12 mm (10) Vis à tête plate, M4 x 12mm (10) Vite a testa piana M4 x 12 mm (10)

TLR255014 Flat Head Screw, M4 x 20 mm (10) Rundkopfschraube, M4 x 20 mm (10) Vis à tête plate, M4 x 20mm (10) Vite a testa piana M4 x 20 mm (10)

TLR255015 Setscrew, Cup Point, M4 x 5 mm (10) Stellschraube, Ringschneide, M4 x 5 mm (10) Vis de ﬁxation, bout cuvette, M4 x 5mm (10) Vite di fermo, a M4 x 5 mm (10)

TLR5901 Button Head Screw, M3 x 6 mm (10) Rundkopfschraube, M3 x 6 mm (10) Vis à tête bombée, M3 x 6mm (10) Vite a testa tonda M3 x 6 mm (10)

TLR5902 Button Head Screw, M3 x 8 mm (10) Rundkopfschraube, M3 x 8 mm (10) Vis à tête bombée, M3 x 8mm (10) Vite a testa tonda M3 x 8 mm (10)

TLR5903 Button Head Screw, M3 x 10 mm (10) Rundkopfschraube, M3 x 10 mm (10) Vis à tête bombée, M3 x 10mm (10) Vite a testa tonda M3 x 10 mm (10)

TLR5904 Button Head Screw, M3 x 12 mm (10) Rundkopfschraube, M3 x 12 mm (10) Vis à tête bombée, M3 x 12mm (10) Vite a testa tonda M3 x 12 mm (10)

TLR5906 Button Head Screw, M3 x 35 mm (10) Rundkopfschraube, M3 x 35 mm (10) Vis à tête bombée, M3 x 35mm (10) Vite a testa tonda M3 x 35 mm (10)

TLR5909 Button Head Screw, M3x16 mm (10) Rundkopfschraube, M3 x 16 mm (10) Vis à tête bombée, M3 x 16mm (10) Vite a testa tonda, M3x16 (10)

TLR5911 Button Head Screw, M3 x 20 mm (10) Rundkopfschraube, M3 x 20 mm (10) Vis à tête bombée, M3 x 20mm (10) Vite a testa tonda, M3 x 20 mm (10)

TLR5932 Cap Head Screw, M3 x 10 mm (10) Inbusschraube, M3 x 10 mm (10) Vis d’assemblage creuse, M3 x 10mm (10) Vite a testa cilindrica M3 x 10 mm (10)

TLR5933 Cap Head Screw, M3 x 12 mm (10) Inbusschraube, M3 x 12 mm (10) Vis d’assemblage creuse, M3 x 12mm (10) Vite a testa cilindrica M3 x 12 mm (10)

TLR5963 Flathead Screw, M3 x 12 mm (10) Flachkopfschraube, M3 x 12 mm (10) Vis à tête plate, M3 x 12mm (10) Vite a testa piana, M3 x 12 mm (10)

TLR5964 Flathead Screw, M3 x 16 mm (10) Flachkopfschraube, M3 x 16 mm (10) Vis à tête plate, M3 x 16mm (10) Vite a testa piana, M3 x 16 mm (10)

TLR6289 Set Screw, M3 x 5 mm (10) Stellschraube, M3 x 5 mm (10) Vis de ﬁxation, M3 x 5mm (10) Vite di fermo, M3 x 5 mm (10)

VTR235005 M2 x 10 mm Cap Head Screw (10) M2 x 10 mm Inbusschraube (10) Vis d’assemblage creuse, M2 x 10mm (10) Vite testa cilindrica M2 x 10 mm (10)

VTR236044 M5 Nylock Flanged Serrated Nut (10) M5 Nylock gezahnte Flanschmutter (10) Écrou dentelé bridé Nylock M5 (10) Dado autobloccante ﬂangiato dentellato M5 (10)

VTR236078 4.3 mm x 9 mm x 0.8 mm Washer (10) 4,3 mm x 7mmx 0,8 mm Unterlegscheibe (10) Rondelle 4,3mm x 9mm x 0,8mm (10) Rondella 4,3 mm x 9 mm x 0,8 mm (10)

DYNB3810EC 7.4V 5000mAh 2S50C LiPo, Hardcase: EC5 7,4 V 5000 mAh 2S50C LiPo, Hartschale: EC5 Li-Po 7,4V 5000mAh, 2S, 50C, coffret: EC5 Batteria Li-Po 7,4V 5000mAh 2S50C, custodia rigida: EC5

DYNB3811EC 11.1V 5000mAh 3S50C LiPo, Hardcase 11,1 V 5000 mAh 3S50C LiPo, Hartschale Li-Po 11,1V 5000mAh,3S, 50C, coffret Batteria Li-Po 11,1V 5000mAh 3S50C, custodia rigida

DYNB3855EC HD7.6V 5000mAh 2S50C LiPo Case 7,6 V 5000 mAh 2S50C LiPo Schale Boîtier Li-Po 7,6V 5000mAh, 2S, 50C Batteria Li-Po HD7,6 V 5000mAh 2S50C, custodia

DYNB3856EC HD11.4V 5000mAh 3S 50C LiPo Case HD11.4V 5000mAh 3S 50C LiPo Schale Boîtier Li-Po HD 11,4V 5000mAh 3S 50C Batteria Li-Po HD11,4 V 5000mAh 3S 50C, custodia

DYNC3005 Passport 400W Dual ACDC Touch Dynamite Passport 400W Dual ACDC Touch Passport400W Dual CA/CC Touch Caricabatterie con touch-screen doppia alimentazione

CA/CC Passport 400W

DYNC3010 UltraForce 220WTouch Charger UltraForce 220W Touch-Akkuladegerät UltraForce 220W TouchCharger Caricabatterie con touch-screen UltraForce 220W

Part # English Deutsch Français Italiano

LOS350002 Cab Section, Clear Baldachinabschnitt,Transparent Section cabine, clair Sezione abitacolo, trasparente

LOS350003 Front Hood, Clear Frontklappe,Transparent Capot avant, clair Cofano anteriore, trasparente

LOS350004 L/R Rear Fender Set, Clear L/R Heck Schutzblechset, Transparent Ensemble protections arrières D/G, clair Serie parafanghi posteriori sinistro/destro, trasparenti

SPM6730 Spektrum Tx Storage Bag Spektrum Tx Aufbewahrungstasche Sac d’entreposage SpektrumTx Borsa stoccaggio SpektrumTx

SPM6740 Optional Speedometer DX2E Optional Tachometer DX2E Compteur de vitesse facultatif DX2E Tachimetro opzionale DX2E

SPM6741 Optional Bluetooth Module DX2E Optional Bluetooth-Modul DX2E Module Bluetooth facultatif DX2E Modulo Bluetooth opzionale DX2E

SPM6742 TM1500 Telemetry Module TM1500 Telemetriemodul Module de télémétrie TM1500 Modulo telemetria TM1500

SPM6743 Spektrum DX2E Active Speedo Bundle Spektrum DX2E Active Tachometer-Bündel Lot de tableaux de bord Speedo DX2E Active Bundle tachimetro Spektrum DX2E Active

SPM6744 Spektrum DX2E Active Dashboard Bundle Spektrum DX2E Active Armatur-Bündel Lot de tableaux de bord Spektrum DX2E Active Bundle cruscotto Spektrum DX2E Active

SPM6745 DX2E Active Phone Mount DX2E Active Telefonhalterung Support de téléphone DX2E Active Supporto telefono DX2E Active

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

38 SUPER BAJA REY®DESERT TRUCK: 1:6 4WD RTR, AVC

EXPLODED VIEW

EXPLOSIONSZEICHNUNG

VUE ÉCLATÉE DES PIÈCES

VISTA ESPLOSA DELLE PARTI