EN
SR-71 Blackbird® Twin 40mm EDF
4
IMPORTANT: After you set up your model, always rebind the transmitter and
receiver to set the desired failsafe positions.
If your transmitter allows it, enable the throttle cut feature. Always engage throttle
cut before approaching the aircraft.
Dual Rates
Low rate is recommended for the initial ights.
NOTICE: To ensure AS3X®technology functions properly, do not lower rate
values below 50%.
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After rst ights, you may adjust exponential in your transmitter.
Transmitter Telemetry Setup
If the transmitter that you intend to use with this aircraft is not displaying telemetry
data, visit Spektrumrc.com and update your rmware. With the latest rmware
installed on your transmitter the telemetry option should now be functional on your
transmitter.
Transmitter Setup
DX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> at the bottom of the list.
The system asks if you want to create a new model, select Create
3. Set Model Type: Select Airplane Model Type by choosing the airplane.
The system asks you to conrm model type, data will be reset. Select YES
4. Set Model Name: Input a name for your model le
5. Select <Main Screen>, Click the scroll wheel to enter the Function List
6. Set D/R (Dual Rate) and Expo; Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% -Low Rates: 70%, Expo 5%
7. Set D/R (Dual Rate) and Expo; Elevator
Set Switch: SWITCH C
Set High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
8. Set Throttle Cut; Switch: Switch H, Position: -100%
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrtum Airware app is open.
Select the orange pen icon in the upper left corner of the screen, the system
asks for permission to Turn Off RF, select PROCEED
2. Select the three dots in the upper right corner of the screen,
select Add a New Model
3. Select Model Option, choose DEFAULT, select Airplane.
The system asks if you want to create a new acro model, select Create
4. Select the last model on the list, named Acro.
Tap on the word Acro and rename the le to a name of your choice
5. Tap and hold the back arrow icon in the upper left corner of the screen to
return to the main screen
6. Go to the Model Adjust menu
7. Set Dual Rates and Expo; Select Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% -Low Rates: 70%, Expo 5%
8. Set Dual Rates and Expo; Select Elevator
Set Switch: SWITCH C
Set High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
9. Set Throttle Cut; Switch: Switch H, Position: -100%
NX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> near the bottom of the
list. Select Airplane Model Type by choosing the airplane, select Create
3. Set Model Name: Input a name for your model le
4. Select <Main Screen>, Click the scroll wheel to enter the Function List
5. Set Rates and Expo; Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% -Low Rates: 70%, Expo 5%
6. Set Rates and Expo; Elevator
Set Switch: SWITCH C
Set High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
7. Set Throttle Cut; Switch: Switch H, Position: -100%
