Horrex UCS curved User manual

Montagehandleiding
UCS curved
Installation Manual

4HORREX MONTAGEHANDLEIDING

5
Package contents 6
1 Symbols 7
2 Options 8
3 Safety instructions 9
4 Use 10
5 Installation 11
5.1 Check before installing 11
5.2 Installation 11
5.3 Use 12
5.4 Maintenance 13
6 Warranty 17
7 Recycling 17
8 Technical data 18
Table of content

6HORREX MONTAGEHANDLEIDING
Package contents
PRODUCTONDERDELENGEREEDSCHAP
S
C
R
E
W
D
R
I
V
E
R
6X*
S
C
R
E
W
3
.
5
*
2
5
S
C
R
E
W
3
.
5
*
2
5
4X
C
O
R
N
E
R
C
A
P
C
O
R
N
E
R
C
A
P
* Systems smaller than 900 mm have 4 wall screws and no Z-clips.
* Systems wider than 900 mm have 6 wall screws and 2 Z-clips.
0X*
Z
-
C
L
I
P
S
Z
-
C
L
I
P
S
1X UCS system
M
E
A
S
U
R
I
N
G
T
A
P
E

7
Caution!
Not following or incorrectly following these instruction can lead to
serious injuries.
Note!
Not following or incorrectly following these instructions can lead to
damage or reduced functionality of the product.
Info
Additional information about the product.
Symbols
1

8HORREX MONTAGEHANDLEIDING
Options
2
Product dimensions Colors
B 314 x H 414 mm RAL9001 of RAL9005
B 524 x H 534 mm RAL9001 of RAL9005
B 594 x H 499 mm RAL9001 of RAL9005
B 734 x H 544 mm RAL9001 of RAL9005
B 784 x H 499 mm RAL9001 of RAL9005
B 852 x H 349 mm RAL9001 of RAL9005
B 994 x H 484 mm RAL9001 of RAL9005
B 1019 x H 499 mm RAL9001 of RAL9005
Spare parts
Clicker
Cord package
Z-clips
Corner cap

9
Please follow the prescribed safety instructions from the vehicle
manufacturer at all times.
Horrex is not responsible for damage caused in the following
situations:
• Incorrect assembly or connection to the product;
• Damage to the product due to mechanical influences;
• Modifications to the product without the permission of the
producer;
• Use for purposes other than described in the manual.
3Safety instructions
Info
If you do not have enough technical knowledge for the
installation, then have the product installed by a special-
ist.

10 HORREX MONTAGEHANDLEIDING
4Use
This product can only be used in vehicles with a minimum wall
thickness of 26 mm, so that the screws do not protrude on the out-
side of the wall.
Use only in combination with the supplied parts or additional parts
from Horrex. This can be found in chapter 2 of this manual.
Het is niet toegestaan het product te gebruiken voor doeleinden It is
not permitted to use the product for purposes other than the usage
shown below.

11
5Installation
5.1 Check before installing
Check before installing if there is enough space available to install
the product, if the UCS does not block any other products after
installing, and if the wall thickness is enough for the supplied screws.
For safety reason, please note the presence of wiring and electrical
components in the installation area. When drilling and/or screwing,
pay particular attention to wiring out of sight.
5.2 Installation
Follow the following steps to install the product.
A: Z-clips are provided when the product is wider than 900
mm. Mount these Z-clips at the right distance from the hole
for the window. For DC windows, this distance is 16 mm from
the window hole. For RK, mount them directly against the
rubber. For PV, the Z-clip should fall around the window hole.
The Z-clips are not applicable for S7 windows.
Distribute the Z-clips evenly over both horizontal sides. Fasten
the Z-clips with the supplied screws.
Note!
In the case of the screws not sticking in the wall, you
should use wall plugs. Pay attention that you do not drill
through the wall when doing this.
Info
It is advised to let a second person assist you when in-
stalling a bigger product.

12 HORREX MONTAGEHANDLEIDING
B: Place the product, with the blackout cassette at the bottom,
against the wall. When Z-clips have been used, make sure that
the profile falls around the clips well. If no Z-clips were used,
align the product neatly on the window.
C: Fasten the UCS against the wall with one screw per corner.
There are two possible screw holes per corner piece. Choose
the hole that is easiest to reach. Use the supplied screws for
this.
D: Click the corner caps on every corner piece.
5.3 Use
The blackout and mesh pull bar of the UCS is stepless adjustable in
height. The pull bars can be moved up and down with one hand.
The blackout pull bar and the mesh pull bar can be clicked together
for extra closure.
Note!
Make sure the UCS is not closed for a long time as this
will cause the material to slacken. If a vehicle is standing
still for a long time, make sure that the material is raised
slightly on both sides but is not clicked together. This
ensures that the blind is ventilated on both sides (to
prevent mold).
Caution!
Risk of damage due to heat build-up between the UCS
and the window panel. If the sun is shining strongly,
close the eclipse material to a maximum height of two
thirds.

13
5.4 Maintenance
Carefully clean the product with a damp cloth regularly.
Note!
Do not use any sharp objects or chemical cleaning
products that could damage the product.

14 HORREX MONTAGEHANDLEIDING
A
?? ??
16 mm.
1/2 1/2
1/3 1/3 1/3

15
B
C

16 HORREX MONTAGEHANDLEIDING

17
6
7Recycling
If possible, carefully separate the packaging material from this
product and discard it in the appropriate bins for recycling.
If you want to dispose of the product itself, ask an employee at
your local waste disposal station how to do this in accordance with
applicable regulations.
Please do not dispose of the product with household, garden and
kitchen waste.
Warranty
A standard 2-year warranty applies to this product. If the product is
defective, first contact your dealer or point of sale.
Distributors of original Horrex products and accessories can be
found on our website:
https://www.horrex.nl/consumers
If you cannot find a solution, or if you have other questions, com-
ments or suggestions, please send a message to: [e-mail]

18 HORREX MONTAGEHANDLEIDING
8Technical
data
Component Material
Basic profile Aluminum
Pull bar Aluminum
Other plastic
components
PA6 / PA6.6
Blackout PET with
aluminumlaag
Mesh Polyester

19

20 HORREX MONTAGEHANDLEIDING

21

Horrex BV
Taanderijstraat 19
3133 ET Vlaardingen
TEL [phone]
www.horrex.nl
[e-mail]
www.drivingchangeint.com