manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Hoselink
  6. •
  7. Lighting Equipment
  8. •
  9. Hoselink L462 User manual

Hoselink L462 User manual

Other Hoselink Lighting Equipment manuals

Hoselink L451 User manual

Hoselink

Hoselink L451 User manual

Hoselink L450 User manual

Hoselink

Hoselink L450 User manual

Hoselink L245 User manual

Hoselink

Hoselink L245 User manual

Popular Lighting Equipment manuals by other brands

Life 39.9F70020C quick start guide

Life

Life 39.9F70020C quick start guide

EuroLite LED ML-20 user manual

EuroLite

EuroLite LED ML-20 user manual

LIGMAN OD-50141 installation manual

LIGMAN

LIGMAN OD-50141 installation manual

Home Accents Holiday 1002461144 instructions

Home Accents Holiday

Home Accents Holiday 1002461144 instructions

Experia IRiS Ripple Light instruction manual

Experia

Experia IRiS Ripple Light instruction manual

Erco Gecko Mounting instructions

Erco

Erco Gecko Mounting instructions

Inter-lux ZTA.100.Surface Installation and maintenance instructions

Inter-lux

Inter-lux ZTA.100.Surface Installation and maintenance instructions

Whelen Engineering Company TN Series installation guide

Whelen Engineering Company

Whelen Engineering Company TN Series installation guide

IKEA BJÖRKSPIREA manual

IKEA

IKEA BJÖRKSPIREA manual

Toolland PM 6640 instruction manual

Toolland

Toolland PM 6640 instruction manual

GTD GTD-LP200 user manual

GTD

GTD GTD-LP200 user manual

LIVARNO home 1105-W-UK manual

LIVARNO home

LIVARNO home 1105-W-UK manual

ProLights EclPar IPMFC user manual

ProLights

ProLights EclPar IPMFC user manual

Velvet EVO Series user manual

Velvet

Velvet EVO Series user manual

IDTOLIGHT GENT installation instructions

IDTOLIGHT

IDTOLIGHT GENT installation instructions

MAYTONI S35 installation manual

MAYTONI

MAYTONI S35 installation manual

MaxLite MLFP14DP4535 user manual

MaxLite

MaxLite MLFP14DP4535 user manual

SLV Elektronik 550621 instruction manual

SLV Elektronik

SLV Elektronik 550621 instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

Solar Party Garland Lights |
Warm White | 25 Bulbs | DAZZLE
For more information visit
hoselink.com.au
or call
1300 900 617
youtube.com/hoselink
MODEL: L462
Solar Party Garland Lights |
Warm White | 25 Bulbs | DAZZLE
MODEL: L462
Cultivating ConnectionsCultivating Connections
User ManualUser ManualUser Manual
REMOTE -
Once the light as been turned on with the ‘ON/OFF’ button on the back of
the panel, you can now use the remote to control the lights. The infrared
remote has a range of up to 3m and must be pointed at the solar panel for
maximum effectiveness. The red power button located in the top left corner
of the remote can be used to toggle the lights on and off.
Use the mode buttons numbered 1-5 to change the lighting mode. Adjust the
brightness of the lights with the two buttons on the bottom of the remote. The
lights will come pre-set to the automatic function, with the day/night sensor
turned on. This means they will automatically turn on at dusk and off at dawn.
If you do not want the light to come on automatically, you can set the lights
to ‘Manual Mode’ by pressing the green ‘M’ button in the top right corner of
the remote. This will deactivate the day/night sensor. This mode is useful if you
only want the lights on at certain times, like when entertaining, or to avoid
wasting its charge. To reactivate the day/night sensor and to turn the
automatic function back on, simply press the ‘AUTO’ button on the remote.
When in ‘Manual Mode’ you can also set a time delay to switch the lights off.
Once the lights are on, press ‘3H’ for a 3-hour delay or ‘6H’ for a 6-hour delay.
The lights will then turn off after the selected amount of time has passed.
Remote comes with 3-volt CR2025L battery included. To replace the remote’s
battery, undo the screw on the back of the remote. Once undone, hold in the
side clip on the battery compartment and pull to remove it. Swap the batteries
and return the compartment to the remote, then tighten the screw back into
place. Dispose of used batteries correctly and safely. Keep out of reach of children.
WARNING - KEEP BUTTON BATTERIES OUT OF REACH OF CHILDREN
• These batteries can cause severe or fatal injuries in 2 hours or less, due to
chemical burns and potential perforation of the esophagus, if it is swallowed
or placed inside any part of the body.
• Never allow children to replace the button batteries in any device.
• If it is suspected a button/coin battery has been swallowed or otherwise placed
inside any part of the body, a person should contact the Australian Poisons
Information Centre on 13 11 26 immediately for 24/7 fast, expert advice.
• Regularly examine devices and make sure the battery compartment is
correctly secured, e.g. that the screw or other mechanical fastener is
tightened. Do not use if compartment is not secure.
• Dispose of used button batteries immediately and safely out of reach of children.
A battery can still be dangerous even when it can no longer power the device.
• Tell others about the risk associated with button batteries and how to keep
their children safe.
Kit Contents
1 x Solar Party Garland Lights | Starter Set | Warm White
These decorative string lights can be used to create a
party atmosphere or relaxing ambience in your space.
Lighting Modes
Solar Party Garland Lights include 5 lighting modes:
- Constant light
- Slow flash
- Quick flash
- Pulsating light
- Fading pulse
Adjust the lighting mode by pressing the ‘MODE’ button
located on the back of the solar panel until the desired
setting is reached or use the mode buttons on the remote.
In its default setting, the built-in intelligent light sensor
detects darkness, automatically illuminating the lights at
dusk and turning them off at dawn. This setting can also
be turned off with the remote, allowing you to use the
lights on a manual setting.
Activate the Light
STEP 1 Find a suitable location
Pick a sunny position for the solar panel as it needs access
to direct sunlight for optimum results; preferably 6-8 hours
a day. Keep in mind the distance between the panel to
the first bulb will be maximum 770mm.
STEP 2 Activate the lights
When first removed from the box, the light will need to be
turned on. Use the ‘ON/OFF’ button located on the back of
the solar panel. If not using the included remote, the ‘MODE’
button can also be used to select which setting you want.
Product Installation - Option 1
Ground spike.
Slot the ground spike into the tube on the back of the
solar panel, then push the spike into the ground.
Product Installation - Option 2
Wall or fence mount.
STEP 1 Mark the holes
Mark out holes with a marker pen.
STEP 2 Drill the holes
Using a 6mm drill piece for masonry installation, drill the two holes.
STEP 3 Hammer the plugs
Gently hammer the plugs into place and then secure the
screws tightly.
FOR TIMBER
Drill 3mm pilot holes to guide screws into place (plastic
plugs are not required).
Using the Remote
A On /Off
BManual Mode
CConstant Light
DSlow Flash
EQuick Flash
FPulsating Light
GFading Light
HAutomatic Mode
I3 Hour Delay
J 6 Hour Delay
KDecrease Brightness
LIncrease Brightness
A B
C D
E F
G H
I J
K L