Hoshizaki DCM-60KE-HC User manual

DCM-60KE-HC
DCM-60KE-P-HC
DCM-120KE-HC
DCM-120KE-P-HC
L1L032201 (122018)
DCM-60KE-HC
Telford 70 Sta󰀨ord Park 7, Telford, Shropshire TF3 3BQ UK
INSTRUCTION MANUAL
(original instructions)
NOTICE D’UTILISATION
(instructions traduites)
BEDIENUNGSANLEITUNG
(Übersetzung)
GEBRUIKSAANWIJZING
(vertaalde instructies)
MANUAL DE INSTRUCCIONES
(instrucciones traducidas)
MANUALE D’ISTRUZIONI
(traduzione)
CUBELET ICE DISPENSER
DISTRIBUTEUR DE CUBELETS
CUBELETEISDISPENSER
CUBELET-IJSDISPENSER
DISPENSADOR DE CUBITOS DE HIELO
DISTRIBUTORE DI GHIACCIO IN CUBETTI

ENGLISH
FRANCAIS
IMPORTANT SAFETY INFORMATION ...................................................................................................1
I. INSTALLATION INSTRUCTIONS.......................................................................................................3
1. CONSTRUCTION .........................................................................................................................3
2. ACCESSORIES ............................................................................................................................3
3. UNPACKING.................................................................................................................................3
4. LOCATION....................................................................................................................................4
5. INSTALLATION.............................................................................................................................4
6. ELECTRICAL CONNECTIONS.....................................................................................................5
7. WATER SUPPLY AND DRAIN CONNECTIONS..........................................................................5
II. OPERATING INSTRUCTIONS ...........................................................................................................6
1. START UP.....................................................................................................................................7
2. DISPENSING ICE .........................................................................................................................8
3. FRONT COVER ............................................................................................................................8
4. PORTION CONTROL ...................................................................................................................8
5. SWITCH LOCK FUNCTION..........................................................................................................9
6. SHUT DOWN ................................................................................................................................9
7. PREPARING THE ICE DISPENSER FOR LONG STORAGE....................................................10
III. MAINTENANCE ................................................................................................................................10
1. CLEANING..................................................................................................................................10
2. INSPECTION AND MAINTENANCE...........................................................................................12
3. BEFORE CALLING FOR SERVICE............................................................................................12
4. DISPOSAL ..................................................................................................................................13
5. WARRANTY................................................................................................................................13
SPECIFICATIONS..................................................................................................................................14
INFORMATIONS DE SECURITE IMPORTANTES................................................................................15
I. CONSIGNES D’INSTALLATION.......................................................................................................17
1. CONSTRUCTION .......................................................................................................................17
2. ACCESSOIRES ..........................................................................................................................17
3. DEBALLAGE...............................................................................................................................17
4. EMPLACEMENT.........................................................................................................................18
5. INSTALLATION...........................................................................................................................19
6. BRANCHEMENTS ELECTRIQUES............................................................................................19
7. BRANCHEMENTS D’ARRIVEE ET DE VIDANGE D’EAU .........................................................20
II. CONSIGNES D’UTILISATION ..........................................................................................................20
1. MISE EN MARCHE.....................................................................................................................22
2. DISTRIBUTION DE GLACONS ..................................................................................................22
3. PANNEAU AVANT......................................................................................................................22
4. COMMANDE DE PORTIONS DE GLACE..................................................................................22
5. FONCTION DE VERROUILLAGE DES COMMUTATEURS ......................................................23
6. ARRET ........................................................................................................................................24
7. PREPARATION DU DISTRIBUTEUR DE GLACONS EN VUE D’UN ENTREPOSAGE DE
LONGUE DUREE........................................................................................................................24
III. ENTRETIEN......................................................................................................................................25
1. NETTOYAGE ..............................................................................................................................25
2. INSPECTION ET ENTRETIEN ...................................................................................................27
3. AVANT D’APPELER UN REPARATEUR....................................................................................27
4. MISE AU REBUT ........................................................................................................................28
5. GARANTIE..................................................................................................................................28
SPECIFICATIONS..................................................................................................................................29

DEUTSCH
NEDERLANDS
WICHTIGE SICHERHEITSHINWEISE...................................................................................................30
I. INSTALLATIONSANLEITUNG..........................................................................................................32
1. KONSTRUKTION........................................................................................................................32
2. ZUBEHÖR...................................................................................................................................32
3. AUSPACKEN ..............................................................................................................................32
4. AUFSTELLORT...........................................................................................................................33
5. INSTALLATION...........................................................................................................................34
6. ELEKTRISCHE ANSCHLÜSSE..................................................................................................34
7. WASSERZULAUF- UND WASSERABLAUFANSCHLÜSSE......................................................35
II. BEDIENUNGSANLEITUNG..............................................................................................................35
1. INBETRIEBNAHME ....................................................................................................................36
2. EISAUSGABE .............................................................................................................................37
3. FRONTABDECKUNG .................................................................................................................37
4. PORTIONSKONTROLLE............................................................................................................37
5. FUNKTION DES SPERRSCHALTERS.......................................................................................38
6. AUSSCHALTEN..........................................................................................................................38
7. MASSNAHMEN FÜR DIE LANGFRISTIGE LAGERUNG DES EISSPENDERS........................39
III. WARTUNG........................................................................................................................................40
1. REINIGUNG................................................................................................................................40
2. INSPEKTION UND WARTUNG ..................................................................................................41
3. VOR ANRUF DES KUNDENDIENSTES.....................................................................................42
4. ENTSORGUNG...........................................................................................................................43
5. GEWÄHRLEISTUNG ..................................................................................................................43
TECHNISCHE DATEN...........................................................................................................................44
BELANGRIJKE VEILIGHEIDSINFORMATIE.........................................................................................45
I. INSTALLATIE-INSTRUCTIES...........................................................................................................47
1. CONSTRUCTIE ..........................................................................................................................47
2. TOEBEHOREN ...........................................................................................................................47
3. UITPAKKEN................................................................................................................................47
4. PLAATSING ................................................................................................................................48
5. INSTALLATIE..............................................................................................................................49
6. ELEKTRISCHE AANSLUITINGEN .............................................................................................49
7. AANSLUITING VAN WATERTOEVOER- EN WATERAFVOERLEIDINGEN.............................50
II. BEDIENINGSINSTRUCTIES ............................................................................................................50
1. OPSTARTEN ..............................................................................................................................51
2. IJSAFGIFTE................................................................................................................................52
3. VOORPANEEL............................................................................................................................52
4. PORTIEREGELING ....................................................................................................................52
5. FUNCTIE BLOKKERINGSSCHAKELAAR..................................................................................53
6. UITZETTEN.................................................................................................................................54
7. DE IJSDISPENSER GEREEDMAKEN VOOR LANGDURIGE OPSLAG ...................................54
III. ONDERHOUD...................................................................................................................................55
1. REINIGEN...................................................................................................................................55
2. INSPECTIE EN ONDERHOUD...................................................................................................57
3. VOORDAT U BELT VOOR SERVICE.........................................................................................57
4. VERWIJDERING.........................................................................................................................58
5. GARANTIE..................................................................................................................................58
SPECIFICATIES.....................................................................................................................................59

ESPAÑOL
ITALIANO
INFORMACIÓN IMPORTANTE DE SEGURIDAD.................................................................................60
I. INSTRUCCIONES DE INSTALACIÓN..............................................................................................62
1. CONSTRUCCIÓN.......................................................................................................................62
2. ACCESORIOS ............................................................................................................................62
3. DESEMBALAJE ..........................................................................................................................62
4. UBICACIÓN ................................................................................................................................63
5. INSTALACIÓN ............................................................................................................................63
6. CONEXIONES ELÉCTRICAS.....................................................................................................64
7. SUMINISTRO DE AGUA Y CONEXIONES DE DRENAJE ........................................................64
II. INSTRUCCIONES DE UTILIZACIÓN ...............................................................................................65
1. PUESTA EN MARCHA ...............................................................................................................66
2. DISPENSACIÓN DE HIELO .......................................................................................................67
3. CUBIERTA DELANTERA............................................................................................................67
4. CONTROL DE FRAGMENTOS ..................................................................................................67
5. FUNCIÓN DE BLOQUEO DEL INTERRUPTOR ........................................................................68
6. DESCONEXIÓN..........................................................................................................................69
7. PREPARACIÓN DEL DISPENSADOR DE HIELO PARA UN ALMACENAMIENTO
PROLONGADO...........................................................................................................................69
III. MANTENIMIENTO ............................................................................................................................70
1. LIMPIEZA....................................................................................................................................70
2. REVISIÓN Y MANTENIMIENTO.................................................................................................72
3. ANTES DE LLAMAR AL SERVICIO TÉCNICO ..........................................................................72
4. ELIMINACIÓN.............................................................................................................................73
5. GARANTÍA..................................................................................................................................73
ESPECIFICACIONES ............................................................................................................................74
INFORMAZIONI IMPORTANTI SULLA SICUREZZA ............................................................................75
I. ISTRUZIONI PER L’INSTALLAZIONE..............................................................................................77
1. COMPONENTI............................................................................................................................77
2. ACCESSORI ...............................................................................................................................77
3. DISIMBALLAGGIO......................................................................................................................77
4. UBICAZIONE ..............................................................................................................................78
5. INSTALLAZIONE ........................................................................................................................79
6. COLLEGAMENTI ELETTRICI.....................................................................................................79
7. COLLEGAMENTO DI ALIMENTAZIONE DELL’ACQUA E COLLEGAMENTO DI SCARICO....80
II. ISTRUZIONI DI FUNZIONAMENTO.................................................................................................80
1. AVVIO .........................................................................................................................................82
2. DISTRIBUZIONE DEL GHIACCIO..............................................................................................82
3. COPERCHIO ANTERIORE.........................................................................................................82
4. COMANDO DOSAGGIO.............................................................................................................82
5. FUNZIONE DI BLOCCO DEGLI INTERRUTTORI......................................................................83
6. ARRESTO...................................................................................................................................84
7. PREPARAZIONE DELLA MACCHINA PER IL RIMESSAGGIO PROLUNGATO ......................84
III. MANUTENZIONE..............................................................................................................................85
1. PULIZIA.......................................................................................................................................85
2. CONTROLLO E MANUTENZIONE.............................................................................................87
3. PRIMA DI RIVOLGERSI ALL’ASSISTENZA...............................................................................87
4. SMALTIMENTO ..........................................................................................................................88
5. GARANZIA..................................................................................................................................88
SPECIFICHE..........................................................................................................................................89

1
ENGLISH
IMPORTANT SAFETY INFORMATION
Throughout this manual, notices appear to bring your attention to situations which could result in
death, serious injury, or damage to the unit.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTICE Indicates a hazardous situation which, if not avoided, could result in damage
to the unit.
HYGIENE Indicates important precautions for hygiene and food safety.
IMPORTANT Indicates important information about the use and care of the unit.
This icemaker uses HFC-free refrigerant (propane) and HFC-free foam insulation that are non-
ozone-depleting and environmentally sustainable materials having very low global warming
potential.
WARNING
This icemaker contains ammable refrigerant in its cooling unit; maintenance and recharging
must therefore only be carried out by authorized technicians.
The refrigerant contained in this icemaker is ammable and sealed in the refrigeration system.
Although the refrigerant does not leak out under normal usage, take utmost care when
handling this icemaker so as not to cause any damages to the system.
In the case of accidental damage to the refrigeration system causing refrigerant leak:
* Do not create a source of ignition in the area.
* Do not operate electrical switches or plugs in the area.
* Do not use naked ame.
* Immediately ventilate the area by opening doors and/or windows.
* Call service engineer.
IMPORTANT
This booklet is an integral and essential part of the product and should be kept and preserved
by the user.
Please read carefully the guidelines and warnings contained herein as they are intended to
provide the installer/user with essential information for the proper installation and the continued
safe use and maintenance of the product.
Please preserve this booklet for any further consultation that may be necessary.

2
ENGLISH
WARNING
This is a commercial ice dispenser, and should be destined only to be used for the purpose for
which it has been expressly designed.
Any other use should be considered improper and therefore dangerous. The manufacturer
will not be held liable or responsible for any damage caused by improper, incorrect and
unreasonable use.
The installation, and relocation if necessary, must be carried out by qualied personnel,
in accordance with current regulations, according to the manufacturer’s instructions.
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.
Do not use mechanical devices or other means to accelerate the defrosting process, other
than those recommended by the manufacturer.
The use of any electrical appliance involves the observance of some fundamental rules. In
particular:
*Instances of high humidity and moisture increase the risk of electrical short circuits and
potential electrical shocks. If in doubt, disconnect the ice dispenser.
*Do not damage the power cord or pull it in order to disconnect the ice dispenser from the
electrical supply network.
*If the supply cord and/or the plug should need to be replaced, it should only be done by a
qualied service engineer.
*Do not touch the electrical parts or operate the switches with damp hands.
*This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, it can however be used
by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge providing they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.
*Children shall not play with the appliance.
*Cleaning and user maintenance shall not be made by children without supervision.
* Do not attempt to modify the ice dispenser. Only qualied personnel may disassemble or
repair the appliance.

3
ENGLISH
I. INSTALLATION INSTRUCTIONS
1. CONSTRUCTION
Magnet Catch Control Panel
Spout
Water Pipe
Front Cover Switch
2. ACCESSORIES
CD 1
Grille 1
Inlet Hose 1
Drain Hose 1
Hose Clamp 1
Brush 1
3. UNPACKING
WARNING
Children should not be allowed in reach of the packaging elements (plastic bags and expanded polystyrene) as they are
potential sources of danger.
DCM-60/120KE-HC DCM-60/120KE-P-HC
* Grille faces up or down depending
on models.
Air Outlet
(Ventilation Louver)
Operation Switch
Drain Pan
Grille*
Dispensing Outlet
Power Cord
Push Lever
(DCM-60/120KE-HC only)
Dispense Switch
(DCM-60/120KE-P-HC only)
Operation Panel
Front Cover
Ice Making Switch
Adjustable Leg
Air Inlet (bottom)
Air Filter
Drain Hose
CD Grille BrushHose ClampInlet Hose

4
ENGLISH
CAUTION
Do not lift or manoeuvre the carton by using the shipping bands.
When moving the unit by hand, hold the unit bottom.
Do not hold the lter to lift up the unit. The condenser ns inside may cause injury.
Always wear protective gloves when carrying the unit.
When handling the carton or the unpacked unit, work in pair to prevent injury.
NOTICE
Remove shipping carton, tape(s) and packing. If packing material is left in the ice dispenser, it will not work properly.
To prevent damage, do not tilt the ice dispenser more than 45°.
1) After removing the packaging, make sure that the ice dispenser is in good condition. If in doubt, please do not use the ice
dispenser but apply to professionally qualied personnel.
2) Remove the protective plastic lm from the exterior. If the ice dispenser is exposed to the sun or to heat, remove the lm after
the ice dispenser cools.
3) Remove the package of accessories. Check the contents according to “2. ACCESSORIES”.
4. LOCATION
WARNING
This ice dispenser is not intended for outdoor use.
The ice dispenser should not be located next to ovens, grills or other high heat producing equipment.
This appliance is not suitable for installation in an area where a water jet could be used.
CAUTION
The location should provide a rm and level foundation for the ice dispenser.
NOTICE
Do not place anything on top of the ice dispenser to obstruct the ventilation louver.
IMPORTANT
Normal operating ambient temperature should be within 5°C to 40°C. Water connection is cold water only. Operation of the ice
dispenser, for extended periods, outside of these normal temperature ranges may a󰀨ect production capacity.
Allow the clearance specied below for proper air circulation and ease of maintenance and/or service should they be required.
Top View Side View
Rear
ICE DISPENSER
Front
Left Right Rear
Front
Top
ICE
DISPENSER
15cm
15cm
15cm 15cm
15cm
In some high humidity environments, condensation may form inside the machine and drip onto the oor. Do not install where
the oor can be a󰀨ected by water.
5. INSTALLATION
CAUTION
Incorrect installation can cause harm to people, animals or other items, for which the manufacturer cannot be held
responsible.
Keep the adjustable leg height within 0 to 15 mm to prevent reduction in leg strength or injury caused by a falling adjuster.

5
ENGLISH
* Place the ice dispenser on a rm level surface at counter top height.
* Turn the leg adjusters to level the unit in both the left-to-right and front-to-rear directions
(tilt limit: within 1 cm).
6. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This ice dispenser requires an earth that meets the national and local electrical code requirements.
To prevent possible severe electrical shock to individuals or extensive damage to the unit, install a proper earth wire to the ice
dispenser.
Disconnect the main power supply before any maintenance, repairs or cleaning is undertaken.
* This appliance requires a separate 220 - 240VAC, 13A supply. The electrical supply must be protected by a suitable circuit
breaker.
* Usually an electrical permit and services of a licensed electrician are required.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter
E or by the symbol or coloured Green or Green-and-Yellow. The wire which is coloured Blue must be connected to the
terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured Red.
* Should the socket outlets in the installation site not be suitable for the plug supplied with your product, the plug must be
removed (cut o󰀨 if it is moulded on plug) and an appropriate plug tted.
If the non-rewirable plug has been cut from the power supply cord, it must be disposed of. There should be no attempt to
reuse it. Inserting such a plug into a socket elsewhere presents a serious risk of electrical shock.
* The non-rewirable plug must never be used without a fuse cover being tted.
The correct replacement for the detachable fuse cover is identiable from the manufacturer’s reference number stamped on
the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki Parts/Service Centres.
Fuses should be rated at 13A and approved to BS 1362.
7. WATER SUPPLY AND DRAIN CONNECTIONS
WARNING
Connect to potable cold water supply only.
* The connections to the mains water supply must be made in accordance with the countries’ current requirements of the Water
Supply or Water Fittings Regulations.
* To avoid performance reduction or malfunction caused by scaling, the water supply should have a hardness of not more
than 50 mg/L and a silica content of not more than 30 mg/L. Otherwise, installation of a proper water treatment device will be
required.
Leg
Adjuster
Shorter
Longer

6
ENGLISH
* Water supply pressure should be minimum 0.05 MPa (0.5 bar) and maximum 0.78 MPa (8 bar). If the pressure exceeds 0.78
MPa (8 bar), use a proper pressure reducing valve. Do NOT throttle back the supply tap.
* A plumbing permit and services of a licensed plumber may be
required in some areas.
* The ice dispenser drain is gravity ow, so ensure drain hose has
an adequate pitch or fall.
* Drain lines should not be installed directly to the sewer system. A
vertical air gap of a minimum of 5 cm should be between the end
of the drain hoses from the ice dispenser and the oor drain.
* Be sure to use the new hose-sets supplied with the appliance.
Do not reuse any old hose-sets.
1) Attach the angled end of exible inlet hose (accessory) to the
G3/4 fitting at the bottom of the ice dispenser as indicated,
ensuring rubber sealing washer is correctly positioned. Hand
tighten su󰀩ciently to provide leak free joint.
2) Attach the other end of inlet hose to the water tap, noting washer is correctly positioned
before hand tightening as above. It is a wise precaution to have a stop valve within easy
reach.
3) Attach the grey exible drain hose (accessory) to the tting at the bottom of the drain pan.
Use the hose clamp (accessory) to obtain a leak free joint.
II. OPERATING INSTRUCTIONS
CAUTION
Do not put your hands into the dispensing outlet. The icemaking mechanism may
suddenly move, resulting in injury.
NOTICE
All parts are factory-adjusted. Improper adjustments may result in failure.
If the unit is turned o󰀨, wait for at least 3 minutes before restarting the ice dispenser to prevent damage to the compressor.
Periods of 5 to 6 hours without dispensing ice could result in wet ice or an ice bridge forming in the storage bin. Always
turn o󰀨 the ice making switch, and remove ice from the storage bin within 2 hours. Soggy and sticky ice should be removed
continuously as produced.
This ice dispenser is programmed to suspend ice dispensing action when the push lever/dispense switch is continuously pressed
for more than 2 minutes. Also, pressing and releasing the push lever/dispense switch repeatedly for extended periods may cause
the protector to stop the ice dispenser.
HYGIENE
This ice dispenser is designed to produce edible ice. To keep the ice dispenser hygienic, follow the instructions in “III. 1.
CLEANING”.
Drain Hose
Hose Clamp
Water Supply
Inlet G3/4
Drain Outlet
Drain
5cm air gap
Inlet Hose
Water Supply Tap
Inlet Hose

7
ENGLISH
IMPORTANT
To prevent ice and/or water from scattering or splashing:
[DCM-60/120KE-HC]
* Use a container with more than a 7 cm opening.
* Place the container about 1 cm below the dispensing outlet
when pressing the push lever to dispense ice and/or water.
[DCM-60/120KE-P-HC]
* Use a container with more than a 7 cm opening and more than
a 12 cm height.
* Place the container in the round centre of the grille when
pressing the dispense switch to dispense ice and/or water.
Clean out the storage bin once a day, or stored ice may melt and refreeze, causing mechanical problems. For e󰀩cient use of
ice, turn o󰀨 the ice making switch before shutting down the ice dispenser. Ice remains available until the storage bin becomes
empty, and water is always available.
[1] [2] [3] [4]
Control Panel
[1] Display
PORTION: Lights up when portion control is activated
BIN FULL: Lights up when storage bin is full
DRAIN: Lights up during drain cycle
Indicates error code “E” in case of error
[2] Drain Switch
[3] Lock Switch
[4] Portion Control Switch
Operation Panel
[1] Service Call Lamp (red)
[2] Lock Lamp (white)
[3] Ice Making Lamp (white)
[4] Water Switch
[5] Ice & Water Switch
[6] Ice Switch
[7] Dispense Switch
1. START UP
1) Plug in the ice dispenser.
2) Open the water supply tap.
3) Move the operation switch, located on the right side of the ice dispenser, to the “ON” position. The display on the control panel
shows the current operating status.
4) Move the ice making switch, located on the right side of the ice dispenser, to the “ON” position. The ice making lamp on the
operation panel lights up, and the ice dispenser starts the automatic ice making process in 5 minutes.
5) Check the water supply and drain connections for water leaks.
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[DCM-60/120KE-HC] [DCM-60/120KE-P-HC]
Min 7 cm
Min
12 cm
Place in
round centre
Min 7 cm
About
1 cm

8
ENGLISH
6) After 10 minutes, push the ice switch on the operation panel.
7) Press the push lever/dispense switch, and check for proper ice dispensing action.
8) The ice dispenser stops the ice making process automatically in 1 hour or so when the storage bin is lled with ice, and
restarts when ice is used.
Note: Soggy and sticky ice may be produced depending on water conditions.
2. DISPENSING ICE
1) Select your dispensing choice by pushing ice switch, ice & water switch, or water switch on the operation panel (factory
adjusted to ice & water). The selected switch lights up.
2) Position a container, and dispense a desired amount of ice and/or water.
[DCM-60/120KE-HC]
Ice and/or water keeps being dispensed while the push lever is pressed.
[DCM-60/120KE-P-HC]
Ice and/or water keeps being dispensed while the dispense switch is held down, or a preset amount is dispensed when the
dispense switch is pressed once (portion control).
3. FRONT COVER
The front cover is equipped with a safety device. When the front
cover is removed, the ice switch, ice & water switch, and water
switch ash and no dispensing action is available.
After accessing the control panel for adjustments, replace the front
cover in its correct position.
NOTICE
To prevent damage to the magnet provided inside, do not drop the front
cover from a height.
1) To remove, hold the notches on both sides of the front cover, and pull it
toward you.
2) To replace, hold both sides of the front cover, insert the hooks into the
holes, and securely attach it to the magnet catch.
4. PORTION CONTROL
Pushing the portion control switch on the control panel activates the preset
portion control for ice and/or water dispensing. The portion control is
deactivated in the default setting.
The amount of ice dispensed in the portion control depends on water quality
and storage bin level. The amount of water dispensed in the portion control
depends on water pressure.
Model Default Setting Adjustable Range
DCM-60KE-HC
DCM-120KE-HC
Ice: 40g
Water: Not adjustable
Ice: 20 - 990g (in 10g steps)
Water: Not adjustable
DCM-60KE-P-HC
DCM-120KE-P-HC
Ice: 40g
Water: 120mL
Ice: 20 - 990g (in 10g steps)
Water: 20 - 990mL (in 10mL steps)
[a] Activating portion control
1) Remove the front cover.
2) Press the portion control switch on the control panel. The display illuminates “PORTION”.
3) To deactivate the portion control, press the portion control switch again. The display goes o󰀨.
Notch (both
sides)
Front Cover
2
1
Front Cover
Magnet
Catch
Front Cover
Hole (two)
Hook

9
ENGLISH
4) Replace the front cover in its correct position.
[b] Adjusting portion control
1) Remove the front cover.
2) Press and hold the portion control switch on the control panel for 3 seconds. The display shows the current portion control
setting for ice dispensing.
3) Press the ashing ice (-) switch or water (+) switch on the operation panel to adjust the amount of ice. The value in the display
decreases or increases by “1” every time the switch is pressed (e.g. “06” = 60g).
[DCM-60/120KE-HC]
4) Press the portion control switch on the control panel. The display illuminates “PORTION”.
5) Replace the front cover in its correct position.
[DCM-60/120KE-P-HC]
4) Press the portion control switch on the control panel. The display goes o󰀨 and illuminates the setting again when it is stored.
Then, the display shows the current portion control setting for water dispensing.
5) Press the ashing ice (-) switch or water (+) switch on the operation panel to adjust the amount of water. The value in the
display decreases or increases by “1” every time the switch is pressed (e.g. “15” = 150mL).
6) Press the portion control switch on the control panel. The display goes o󰀨 and illuminates the setting again when it is stored.
Then, the display illuminates “PORTION”.
7) Replace the front cover in its correct position.
5. SWITCH LOCK FUNCTION
Pushing the lock switch on the control panel locks the ice switch, ice & water switch, and water switch operations. The switch
lock function is deactivated in the default setting.
1) Remove the front cover.
2) Select your dispensing choice by pushing ice switch, ice & water switch, or water switch on the operation panel. The selected
switch ashes. Press the lock switch on the control panel. The lock lamp on the operation panel lights up.
3) To deactivate the switch lock function, press the lock switch again. The lock lamp goes o󰀨.
4) Replace the front cover in its correct position.
6. SHUT DOWN
This ice dispenser must be shut down and drained every day at the end of service hours.
1) Move the ice making switch, located on the right side of the ice dispenser, to the “OFF” position.
[DCM-60/120KE-HC]
2) Check that the lock lamp on the operation panel is o󰀨. If it is on, press the lock switch on the
control panel to deactivate the switch lock function.
3) Press the ice switch on the operation panel. The ice switch lights up.
4) Place a large container right under the dispensing outlet, and keep pressing the push lever until
no more ice is dispensed.
5) Remove the front cover.
[DCM-60/120KE-P-HC]
2) Press and hold the ice switch, ice & water switch, and water switch at the same time for 3 seconds. The dispense switch
ashes, and the continuous dispensing becomes available.
Note: To deactivate the continuous dispensing, move the ice making switch to the “ON” position or remove the front cover.

10
ENGLISH
3) Place a large container right under the dispensing outlet, and press the dispense
switch once. The ice dispenser keeps dispensing ice for 2 minutes.
Note: To stop dispensing ice within 2 minutes, press the dispense switch again.
4) Press the dispense switch again to check no more ice is dispensed.
5) Remove the front cover. The dispense switch stops flashing, and the continuous
dispensing is deactivated.
[All models]
6) Press the drain switch on the control panel. The display illuminates “DRAIN” during the drain cycle of about 30 seconds.
7) After about 30 seconds, check that the display is o󰀨.
8) Replace the front cover in its correct position.
9) Move the operation switch, located on the right side of the ice dispenser, to the “OFF” position.
10) Unplug the ice dispenser.
11) Close the water supply tap.
NOTICE
When restarting the ice dispenser, make sure that more than 3 hours have passed since the ice making switch was moved to
the “OFF” position, then follow the instructions in “1. START UP”.
7. PREPARING THE ICE DISPENSER FOR LONG STORAGE
NOTICE
This ice dispenser will not work at subfreezing temperatures. To prevent damage to the water supply line, drain the ice
dispenser when air temperature is below zero.
HYGIENE
When shutting down the ice dispenser for two or more days, drain the ice dispenser to prevent contamination in the water
circuit.
1) Follow the instructions in “6. SHUT DOWN”.
2) Remove the inlet hose from the water supply tap, and drain the hose.
3) Ask for draining of the ice dispenser by professional qualied personnel.
III. MAINTENANCE
1. CLEANING
WARNING
Before carrying out any cleaning or maintenance operations, unplug the ice dispenser from the electrical supply network.
This appliance must not be cleaned by use of a water jet.
CAUTION
When using a neutral cleaner or sodium hypochlorite, thoroughly read and understand the instructions provided to prevent
potential health problems.
NOTICE
Ask a trained service person to clean and sanitise the ice dispenser water system at least twice a year and to check and clean
the condenser at least once a year.
To prevent possible damage, do not clean the plastic parts with water above 40°C or in a dishwasher.

11
ENGLISH
[a] Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use a damp cloth containing a neutral cleaner to wipe o󰀨
grease or dirt.
[b] Front Panel, Spout, Push Lever, Ice Dispensing Outlet Cleaning/Sanitisation (Daily)
1) Remove the front cover by holding the notches on
both sides and pulling it toward you. See “II. 3. FRONT
COVER”.
2) Loosen the band to disconnect the water pipe (A).
3) Hold the hooks on both sides of the spout, and pull it
toward you.
4) Either mix 1 litre of water with 4 ml of 5.25% sodium
hypochlorite solution in a suitable container, or the
recommended Hoshizaki sanitiser as directed.
5) Soak a clean cloth with the solution, and wipe the front
cover.
6) Soak the spout in the solution for more than 3 minutes.
Use the accessory brush to clean the water pipe (B).
Rinse thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
7) Soak a clean cloth with the solution, and wipe the parts
around the ice dispensing outlet and the push lever.
8) Replace the spout by holding the hooks on both sides
and inserting them into the holes.
9) Use the band to reconnect the water pipe (A) to the
spout.
10) Replace the front cover by holding both sides, inserting the hooks into the holes, and securely attaching it to the magnet
catch. See “II. 3. FRONT COVER”.
11) The remaining solution can be used to sanitise utensils.
Note: Do not wipe dry or rinse after sanitising, but allow to air dry.
[c] Grille, Drain Pan Cleaning/Sanitisation (Daily)
1) Either mix 1 litre of water with 4 ml of 5.25% sodium
hypochlorite solution in a suitable container, or the
recommended Hoshizaki sanitiser as directed.
2) Lift the grille o󰀨 the drain pan.
3) Soak the grille in the solution for more than 3 minutes.
Rinse thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
4) Use the accessory brush to clean the three drain holes in the drain pan.
5) Place the grille in its correct position and direction.
Water Pipe (A)
Band
Hook
(both sides)
Spout
Front Cover
Water Pipe (B)
Spout
Brush
2
Water Pipe (A)
Band
Push Lever Ice Dispensing
Outlet
1
Hole (both
sides)
Hook
(both sides)
Spout
DCM-60/120KE-HC
Grille must be lower
than the top of drain
pan.
DCM-60/120KE-P-HC
Grille must be level
with the top of drain
pan.
Drain Pan Top
Grille
Lift
o󰀨

12
ENGLISH
[d] Air Filter
CAUTION
To prevent injury, be careful not to touch the condenser ns when removing the air lter.
Plastic mesh air lters remove dirt or dust from the air, and keep the condenser from
getting clogged. If the lters get clogged, the ice dispenser’s performance will be
reduced. Remove and clean the air lter(s) at least twice per month:
1) Pull out the air lter from the bottom of the drain pan.
2) Clean the air lter by using a vacuum cleaner. When severely clogged, use warm
water and a neutral cleaner to wash the air lter.
3) Rinse and dry the air lter thoroughly.
NOTICE
After cleaning, be sure to place the air lter back in position with the handle facing down.
2. INSPECTION AND MAINTENANCE
NOTICE
To achieve optimum ice dispenser performance, the following parts need periodic inspection and maintenance:
Extruding head (upper bearing)
Housing (lower bearing)
Mechanical seal
[a] Inspection
These parts should be inspected after two years from installation or 10,000 hours of operation, whichever comes rst, and once
a year afterwards. Replacement of these parts is required if wear exceeds factory recommendations.
Their service life, however, depends on water quality and environment. More frequent inspection and maintenance are
recommended in bad or severe water conditions.
Consult with your local Hoshizaki service agent about inspection and maintenance service.
[b] Replacement
The extruding head (upper bearing) and mechanical seal must be replaced after four years from installation or 20,000 hours of
operation, whichever comes rst, to prevent the risk of serious accidents or failures. Contact your local Hoshizaki service agent
for replacement.
When the total operating time reaches 20,000 hours, the service call lamp on the operation panel lights up and the display
on the control panel ashes “PC”. Then, after 500 hours, the unit shuts down to ensure safety and the service call lamp starts
ashing. Contact your local Hoshizaki service agent for replacement as soon as the service call lamp lights up.
Once the unit shuts down after 500 hours and the service call lamp starts ashing, the operation can be resumed by turning o󰀨
the operation switch and turning it back on. But the unit shuts down again after 500 hours. To resume the operation, contact
your local Hoshizaki service agent for the required replacement.
Replacement of the housing (lower bearing) may be required depending on water quality and wear condition.
3. BEFORE CALLING FOR SERVICE
WARNING
Do not damage the refrigerant circuit.
Air Filter
Handle

13
ENGLISH
[a] Error Code Indication
If the error code “E” is indicated on the display, before calling for service, check the following.
Code Remedy
E0 Possibility of water leaks. Turn OFF operation switch, and turn it ON again. If error code appears again, call for
service.
E1 Low ice production. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
E2 Water supply circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for
service.
E3 Gear motor failure. Turn OFF operation switch, and turn it ON again after 10 minutes. If error code appears again, call
for service.
E4 Abnormal high side pressure. Clean air lter. Check that ice dispenser is properly installed. Turn OFF operation switch,
and turn it ON again. If error code appears again, call for service.
E5 Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
Eb Electric circuit failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
Ed Operation board communication error. Turn OFF operation switch, and turn it ON again. If error code appears again,
call for service.
EE Gear motor failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EF Supply voltage is too low. Check that voltage is in required range and ice dispenser is not sharing a single receptacle
with other appliances. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EL Bin control switch failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
EP Model setting number error. Turn OFF operation switch, and turn it ON again. If error code appears again, call for
service.
EU Controller board failure. Turn OFF operation switch, and turn it ON again. If error code appears again, call for service.
[b] No Error Code Indication
If the ice dispenser does not work properly or does not work at all with the ice making lamp on the operation panel ashing and
no error code is indicated on the display, before calling for service, check that:
* The power is supplied to the unit.
* The water is turned on.
* The air lter is clean.
For further assistance or advice, contact your local Hoshizaki service agent.
4. DISPOSAL
Comply with local regulations regarding disposal of this appliance and its refrigerant gas.
Correct disposal of this product:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device, use the return and collection
systems or contact the retailer where the product was purchased. They can take this product for environmental safe
recycling.
5. WARRANTY
Hoshizaki warrants to the original owner/user that all Hoshizaki branded products shall be free of defects in material and/or
workmanship for the duration of the “warranty period”. The warranty shall be e󰀨ective for two years from the date of installation.
Hoshizaki’s liability under the terms of the warranty are limited and shall exclude routine servicing, cleaning, essential
maintenance and/or repairs occasioned by misuse and installations not in accordance with Hoshizaki guidelines.
Warranty repairs should be completed by an approved Hoshizaki dealer or service agency using genuine Hoshizaki components.
To obtain full details of your warranty and approved service agency, please contact your dealer/supplier, or the nearest Hoshizaki
Service o󰀩ce:

14
ENGLISH
Hoshizaki UK - UK, Ireland
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Deutschland - Germany, Switzerland, Austria
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki France - France
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Nederland & België - Netherlands, Belgium,
Luxembourg
TEL: [phone] (Nederland)
TEL: [phone] (België)
FAX: [phone]
[email protected] (Nederland)
[email protected] (België)
Hoshizaki Iberia - Spain, Portugal
TEL: [phone]
FAX: [phone]
[email protected]
Hoshizaki Europe B.V. - all other countries within Europe and
Africa
TEL: [phone]
FAX: [phone]
[email protected]
SPECIFICATIONS
Model DCM-60KE-HC DCM-60KE-P-HC
Type Air-cooled, cubelet ice, push lever type Air-cooled, cubelet ice, dispense switch type
Power Supply 1 phase 220-240 50Hz 1 phase 220-240 50Hz
Electric Consumption 280W (ambient 32°C, water 21°C) 280W (ambient 32°C, water 21°C)
Ice Production per 24h 60kg (ambient 10°C, water 10°C) 60kg (ambient 10°C, water 10°C)
Dimensions 350mm(W) x 585mm(D) x 695(-710)mm(H) 350mm(W) x 585mm(D) x 695(-710)mm(H)
Refrigerant R290, 85g R290, 85g
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 45kg (Gross: 54kg) Net: 45kg (Gross: 54kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.78 MPa (0.5 - 8 bar) 0.05 - 0.78 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 6% Rated voltage ± 6%
Model DCM-120KE-HC DCM-120KE-P-HC
Type Air-cooled, cubelet ice, push lever type Air-cooled, cubelet ice, dispense switch type
Power Supply 1 phase 220-240 50Hz 1 phase 220-240 50Hz
Electric Consumption 400W (ambient 32°C, water 21°C) 400W (ambient 32°C, water 21°C)
Ice Production per 24h 125kg (ambient 10°C, water 10°C) 125kg (ambient 10°C, water 10°C)
Dimensions 350mm(W) x 585mm(D) x 815(-830)mm(H) 350mm(W) x 585mm(D) x 815(-830)mm(H)
Refrigerant R290, 95g R290, 95g
Insulation Foam Blowing Agent HFC-free HFC-free
Weight Net: 55kg (Gross: 64kg) Net: 55kg (Gross: 64kg)
Ambient Temp 5 - 40°C 5 - 40°C
Water Supply Temp 5 - 35°C 5 - 35°C
Water Supply Pressure 0.05 - 0.78 MPa (0.5 - 8 bar) 0.05 - 0.78 MPa (0.5 - 8 bar)
Voltage Range Rated voltage ± 6% Rated voltage ± 6%
Note: The above specications are for the representative models.

15
FRANCAIS
INFORMATIONS DE SECURITE IMPORTANTES
Tout au long de ce manuel, des avis attirent votre attention sur des situations qui pourraient
entraîner la mort, des blessures graves ou des dégâts à l’appareil.
AVERTISSEMENT Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des blessures graves voire mortelles.
ATTENTION Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des blessures mineures ou modérées.
AVIS Signale une situation dangereuse qui, si elle n’est pas évitée, peut
entraîner des dégâts à l’appareil.
HYGIENE Signale des précautions importantes à prendre en matière d’hygiène et
de sécurité alimentaire.
IMPORTANT Signale des informations importantes sur l’utilisation de l’appareil et son
entretien.
La machine à glace emploie du uide frigorigène exempt de HFC (propane) et une isolation en
mousse exempte de HFC, non nocifs pour la couche d’ozone, ainsi que des matériaux durables
qui ont très peu d’impact sur le réchau󰀨ement mondial.
AVERTISSEMENT
L’unité de refroidissement de la machine à glace contenant des uides frigorigènes inammables,
son entretien et son rechargement ne doivent être réalisés que par des techniciens agréés.
Le uide frigorigène de cette machine à glace est inammable et est enfermé dans le système
de réfrigération. Bien que le fluide frigorigène ne présente aucun risque de fuite dans des
conditions d’utilisation normales, manipulez la machine à glace avec la plus grande précaution
an d’éviter d’endommager le système.
En cas de fuite de fluide frigorigène résultant d’un dommage accidentel au système de
réfrigération :
* Interdire toute étincelle ou corps incandescent dans le voisinage.
* N’utiliser aucun interrupteur ni prise électrique dans le voisinage.
* Ne pas utiliser de amme nue.
* Ventiler immédiatement la pièce en ouvrant les portes et/ou fenêtres.
* Appeler un technicien de réparation.
IMPORTANT
Ce livret est un élément essentiel qui fait partie intégrante du produit et il doit être conservé
soigneusement par l’utilisateur.
Veuillez lire attentivement les conseils et les avertissements qui s’y trouvent, car ils ont pour
but de fournir à l’installateur et à l’utilisateur des informations essentielles pour une installation
correcte, une utilisation en toute sécurité et un entretien adéquat du produit.
Veuillez conserver précieusement ce livret pour toute référence ultérieure.

16
FRANCAIS
AVERTISSEMENT
Ce distributeur de glaçons a été conçu pour des applications commerciales ; il ne peut être
utilisé qu’aux ns auxquelles il est expressément destiné.
Toute autre utilisation doit être considérée comme inappropriée et donc dangereuse.
Le fabricant décline toute responsabilité pour les dégâts provoqués par une utilisation
inappropriée, incorrecte et abusive.
L’installation, et le transfert le cas échéant, doivent être effectués par un personnel
qualié, conformément aux réglementations en vigueur et aux consignes du fabricant.
Veillez à ce que les ouvertures de ventilation de l’enceinte de l’appareil et de la structure
intégrée ne soient pas obstruées.
Pour accélérer le processus de décongélation, ne pas utiliser d’équipements mécaniques ni
des méthodes autres que celles recommandées par le fabricant.
L’utilisation de tout appareil électrique implique le respect de certaines règles fondamentales.
En particulier :
*En cas de forte humidité, les risques de court-circuit et d’électrocution augmentent. En cas
de doute, débrancher le distributeur de glaçons.
*Ne pas endommager le cordon d’alimentation et ne pas tirer sur le cordon d’alimentation pour
débrancher le distributeur de glaçons.
*Si le cordon et la fiche d’alimentation électrique sont à remplacer, l’opération doit être
e󰀨ectuée par un technicien qualié.
*Ne pas toucher les pièces électriques ou les commutateurs avec les mains humides.
* Cette machine n’est pas prévue pour une utilisation par des personnes (y compris des
enfants) aux capacités physiques, sensorielles ou mentales réduites, ou manquant
d’expérience ou de connaissances. Elle peut cependant être utilisée par des enfants d’au
moins 8 ans et des personnes aux capacités physiques, sensorielles ou mentales réduites,
ou manquant d’expérience ou de connaissances, si une personne responsable de leur
sécurité les surveille ou leur a indiqué les consignes d’utilisation de la machine.
*Les enfants ne doivent pas jouer avec la machine.
*Le nettoyage et l’entretien régulier ne doivent pas être effectués par des enfants sans
surveillance.
* Ne pas tenter de modier le distributeur de glaçons. Cet appareil ne peut être démonté ou
réparé que par du personnel qualié.