Hougen 08180 User manual

The 08180 Kit is used to install a Tapping Attachment onto the HMD917 "Slot Drive" spindle. The Slot Drive
assembly will have one 5/16-18 x 3/8 set screw at the top of the arbor body.
Locate and remove the 1/4-28 X 1/4 Button Head
Cap Screw from the Coolant Inducer with a 5/32"
Hex Wrench.
Rotate the Arbor Body so the 5/16-18 x 3/8 set screw
inside, aligns with the hole in the Coolant inducer. Insert
the 5/32" Hex Wrench and turn the inside set screw 1 full
turn counterclock-wise or until loose.
Remove both 3/8-24 x 3" Hex Bolts from the Front
Support Bracket using a 9/16 wrench. Now the
entire Arbor Body Assembly can be removed.
Continued
08180 TAPPING ATTACHMENT KIT
For use on Hougen Drill Models HMD917
5/16-18 x 3/8
Set Screw
Slide the Slot Drive Adapter and Tap-Matic Assembly
up onto the Motor Spindle at the base of the Motor.
While holding the Assembly up, tighten the 5/16-18 x
3/8 Set Screw supplied with the Kit.
Install the 1/4-20 x 2-1/2 Set Screw and 1/4-20 Lock
Nut into the Stop Block as shown. Mount the Stop
Block Assembly to the Magnet with the supplied 3/8-
24 Hex Bolts and tighten with a 9/16" Wrench.
Install the Stop Arm to the Tap-Matic Assembly with
the 3 Button Head Screws supplied with the Tap-Matic.
Thread the Slot Drive Adapter into the top of the
Tap-Matic Assembly and install the 5/16-18 x 3/8 Set
Screw into the side of the Slot Drive Adapter.
12
34
56
3/8-24 X 3”
Front Support Bracket Bolts

Collet
Collet Retainer Tap
Jaws
Select the correct size Collet for the Tap that will be
used and install it into the bottom of the Tap-Matic.
Collet 10807 - Taps #10 thru 1/2"
Collet 10808 - Taps 1/2" thru 3/4"
Thread the Collet Retainer onto the Tap-Matic
holding the Collet in place. Do not tighten the Collet
Retainer until the next step.
Install the appropriate Tap up thru the Collet Retainer
until the at sides of the Tap are in the Jaws of the Tap-
Matic. Tighten the Jaws so the Tap is held. Then tighten
the Collet Retainer with the supplied wrenches.
Adjust the long Stop Screw to the appropriate depth and lock
in place with the lock nut.
CAUTION
When the Tap is working down into the material the Stop Arm will rotate
and make contact with the Drill Housing on the opposite side that is shown.
When the Tap direction changes and the Tap is working out of the material
it will rotate again to the opposite side. Keeps hands clear of the Stop Arm
while operating.
Stop Arm
Stop Screw
Operating the Tapping Attachment
MUST TAP IN LOW GEAR 250RPM
1. Produce the Correct size hole for the Tap you
are using.
2. Install the Tap-Matic unit using the instructions
above.
3. Position the machine so the Tap is centered
and just above the hole.
4. Applied Slick-Stik Lube or a alternative oil
appropriate for tapping.
5. Lock the magnet in position and verify the Tap
is still centered over the hole.
6. Start the Motor using the Operating Instruction
in the Operators Manual.
7. Rotate the Feed Handles down until the Tap
pulls thru the material.
8. When the Tap-matic Assembly makes contact
with the Stop Screw the gears will disengage
and the Tap will stop turning.
9. While rotating Feed Handles to bring the
Tap-Matic UP, the Tap will engage and turn
counter clockwise.
10. Rotate the Feed Handles until the Tap is clear
of the work piece and push the Motor OFF button.
MOTOR
10937 TAPPING ATTACHMENT KIT
Set-Screw
Spindle Adapter
Approx. 1.625”
3.875” when the Motor is in the UP position
with 4” of stroke down. Magnet
Tapping Attachment
Included in the Kit
Approx. 6”
78
9
Hougen Manufacturing, Inc.
P.O. Box 2005 • Flint, MI 48501-2005
3001 Hougen Drive • Swartz Creek, MI 48473
Phone [phone] • Fax [phone]
www.hougen.com • [email protected]
© 2014 Hougen Manufacturing, Inc.
FORM 08183