HouseWarmer HWFMC-72UH-1 User manual

Page 1
INSTRUCTIONS MUST BE LEFT WITH OWNER FOR FUTURE REFERENCE AFTER INSTALLATION.
INSTALLATION INSTRUCTIONS
MANTEL
SURROUNDS AND
MANTEL SHELF
COMBO UNIT
HWFMC-72UH-1
SURROUNDS
HWFMS-48(UO,W)-1
MANTELSHELVES
HWMS-60(UO,W)-1
HWMS-72(UO,W)-1
Recommended for use with most replaces from 32 to
42 inches wide and up to 38 inches tall. Reference your
replace manufacturer’s instructions for clearance to
combustible requirements.
Mantel Modication Instructions
1. When modifying the surround (HWFMS48(UO,W)) to match
the HWMS60(UO,W) mantelshelves, the cuts shown in
Figure 1 give the best appearance. No modication is
necessary for the HWFMC72.
12”
12” 12”
Figure 1
Note: Top and side trim will need to be cut to t these modi-
cations.

M10537-0-0710Page 2 Empire Comfort Systems Inc. • 918 Freeburg Avenue • Belleville, IL 62220
Mantel Installation Instructions
1. Align and attach the breast board to the right and left side
assemblies. See Figure 2. Breast board ends should be at
against the inside edges of the side assemblies and ush at the
top of the side assemblies. Use of a square is recommended to
ensure a 90° installation.
BREAST BOARD
LEFT SIDE
ASSEMBLY
RIGHT SIDE
ASSEMBLY
1-1/4” SCREWS
Figure 2
2. Attach the 42” wall cleat 49-1/2” above the oor. Ensure that
the wall cleat is level. See Figure 3.
FLOOR
WALL CLEAT
49-1/2”
1-1/4” SCREWS
Figure 3
3. Attach the surround assembly to the wall cleat using two
nishing nails through the breast board. See Figure 4.
Figure 4
4. Attach the top inside edge trim to the bottom of the breast
board using two nishing nails. See Figure 5.
BREAST BOARD
TOP INSIDE
EDGE TRIM
Figure 5
5. Attach the side inside edge trim to the left and right side
assemblies using two nishing nails on each side. See
Figure 6.
INSIDE EDGE TRIM
Figure 6

M10537-0-0710 Page 3Empire Comfort Systems Inc. • 918 Freeburg Avenue • Belleville, IL 62220
6. Center and attach the 42” wall cleat 4-5/8” above the sur-
round using two 1-1/4” drywall screws. See Figure 7.
4-5/8”
UPPER WALL CLEAT
Figure 7
7. Align and attach the mantelshelf to wall cleat using two
nishing nails. If mounting HWMS(60,72)(UO,W) only,
see the rebox manufacturer’s instructions for clearance to
combustible requirements. See Figure 8.
Figure 8

M10537-0-0710Page 4 Empire Comfort Systems Inc. • 918 Freeburg Avenue • Belleville, IL 62220
HOUSEWARMER is a registered trademark of
Empire Comfort Systems Inc.
www.housewarmerproducts.com
EMPIRE
EMPIRE
Comfor t Systems
Manufactured by:
Empire Comfort Systems Inc.
918 Freeburg Ave. Belleville, IL 62220
PH: 877-459-1583
FAX: [phone]
1
2
1
3
45
6
7
PARTS LIST
Common
Index No. Part No. Description Quantity
Supplied
1 M10577 Wall Cleat 2
UO Models
2 M10547 Mantelshelf - 60” 1
2M10539 Mantelshelf - 72” 1
3 M10557 Breast Board 1
4 M10565 Side Assembly - Left 1
5 M10558 Side Assembly - Right 1
6 M10568 Trim - Top 1
7 M10566 Trim - Side 2
UH Models
218491 Mantelshelf - 72” 1
3 M10570 Breast Board 1
4 M10580 Side Assembly - Left 1
5 M10572 Side Assembly - Right 1
6M10599 Trim - Top 1
7M10597 Trim - Side 2
W Models
2M10596 Mantelshelf - 60” 1
2 M10545 Mantelshelf - 72” 1
3 M10601 Breast Board 1
4M10579 Side Assembly - Left 1
5 M10571 Side Assembly - Right 1
6, 7 M10582 Trim Set 1
Hardware Packs
Part Number Models Used On
M10536 HWFMC72UH and HWFMS48(UO,W)
M10603 HWMS(60,72)(UO,W)
Hardware included in packs Quantity Included
M10536 M10603
1-1/4” Screw
8 2
Finishing Nail 10 2