HP 647590-B21 User manual

The HP FlexFabric 10Gb 2-port 554M adapter supports Virtual Connect Flex-10 that allows each 10Gb port to be divided into four
physical NICs to optimize bandwidth management for virtualized servers. When connected to a Data Center Bridging (DCB) capable
switch, Fibre Channel over Ethernet (FCoE) and Ethernet I/O are separated and routed to the corresponding network. For iSCSI storage,
the HP 554M supports full protocol offload to provide better CPU efficiency when compared to software initiators, thus enabling the
server to handle increased virtualization workloads and compute-intensive applications. This combination of high-performance
network and storage connectivity reduces cost and complexity and provides the flexibility and scalability to fully optimize Gen8
BladeSystem servers. The HP 554M delivers the performance benefits and cost savings of converged network connectivity for HP
BladeSystem servers. The dual-port HP 554M optimizes network and storage traffic with hardware acceleration and offloads for
stateless TCP/IP, TCP Offload Engine (TOE), Fibre Channel over Ethernet (FCoE) and iSCSI.
HP FlexFabric 10Gb 2-port 554M Adapter
Models
HP FlexFabric 10Gb 2-port 554M Adapter 647590-B21
NOTE: The HP 554M on each server blade connects to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000
Enclosure) or bays 2-4 (HP BladeSystem c3000 Enclosure).
NOTE: The HP 554M adapter requires a minimum of 2 GB of server memory.
NOTE: The HP 554M adapter supports linking at 1Gbps or 10Gbps when not connected to a Flex-10 device. The HP
554M adapter will only support 1Gbps when connected to a 1Gb Ethernet interconnect.
Kit Contents HP FlexFabric 10Gb 2-port 554M Adapter
Quick install card
Product warranty statement
Drivers, user guide, and utilities via: http://www.hp.com
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Overview
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 1

HP ProLiant Server
Support
HP ProLiant BL420c Gen8
HP ProLiant BL460c Gen8
HP ProLiant BL465c Gen8
HP ProLiant BL660c Gen8
Supported Interconnect
Modules
HP Virtual Connect Flex-10 Ethernet Module
HP Virtual Connect FlexFabric 10Gb/24-port Module
HP 1/10Gb Virtual Connect Ethernet Module
HP 1/10Gb-F Virtual Connect Ethernet Module HP
HP 6120XG Blade Switch
HP 6120G/XG Blade Switch
HP 6125G/XG Ethernet Blade Switch
HP 1:10Gb Ethernet BL-c Switch
Cisco Catalyst 3120G Blade Switch for HP
Cisco Catalyst 3120X Blade Switch for HP
Cisco Catalyst 3020 Blade Switch
Cisco Fabric Extender B22HP for HP
HP GbE2c Layer 2/3 Ethernet Blade Switch
HP 10GbE Pass-Thru Module
HP 1GbE Pass Thru Module
NOTE: Except for the HP Virtual Connect Flex-10 Ethernet Module, HP Virtual Connect Flex Fabric Module,
HP 6120XG, HP 10GbE Pass-Thru Module and the Cisco B22 Fabric Extender, all other supported
interconnects are limited to 1Gb per port connection.
Tape Drive Support
(Nearline Tape Products)
D2D
VLS
ESL libraries
EML libraries
ESL G3 library
MSL G3 libraries (2024, 4048, 8096)
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Compatibility
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 2

Performance
Product Features Industry-leading throughput and latency performance
Supports Gen8 c-Class ProLiant BladeSystem servers
Type A Mezzanine Adapter
Dual 10Gb ports provide up to 40Gb full duplex per adapter
Hardware acceleration and offloads for stateless TCP/IP, TCP Offload Engine (TOE), Fibre Channel
over Ethernet (FCoE) and iSCSI
802.1p, 802.1q, 802.1qau, 802.3ad, 802.3ae, 802.3ap (10GBase-KX4) and 802.3x
Jumbo frames support
Supports HP's FlexFabric and Flex-10 technologies that allow setting any bandwidth from 100Mb to
10Gb on up to four physical function NICs or Flex NICs per port when combined with the 10Gb Flex-
10 Virtual Connect module. One of the Flex NICs can be configured to support FCoE or accelerated
iSCSI.
Each FlexNIC and FlexHBA is recognized by the server as a PCIe physical function device with
adjustable speeds from 1Gb to 10Gb in 100Mb increments
Supports receive-side scaling (RSS) for efficient distribution of network receive processing across
multiple CPUs in multiprocessor systems.
Includes 128 MB of onboard memory.
Supports the Preboot eXecution Environment (PXE
Supports SR-IOV
Dual-port 10 Gigabit
Ethernet Throughput
(theoretical bandwidth)
The 20 Gbps full duplex Ethernet transfer rate per port (40 Gbps aggregate full duplex) delivers
outstanding network performance that improves response time and removes bottlenecks.
Fibre Channel over
Ethernet (FCoE)
Combines the functionality of an industry-standard NIC with a proven Fibre Channel software stack to
seamlessly converge network and storage traffic over a shared lossless Ethernet network based on IEEE
DCB standards.
HP Virtual Connect Flex-
10 10Gb Ethernet Module
for the c-Class
BladeSystem
Evolve 10Gb at your own speed! When paired with the HP Virtual Connect Flex-10 10Gb Ethernet
Modules, take advantage of four Flex NICs, which are PCI Physical Function devices that are OS/ Hypervisor
independent.
Server ROM recognizes them as individual NICs
Speeds can be set per NIC from 100Mb to 10Gbs in 100Mb increments
Three fold increase in number of network connections per port.
Up to four physical function NICs per port.
Ideal for virtualized server environment, especially for dedicated bandwidth application like virtual
machine migration from one physical server to another physical server.
Jumbo Frames The HP 554M adapter supports jumbo frames (also known as extended frames) with a maximum
transmission unit (MTU) of up to 9K bytes when running Ethernet and/or iSCSI I/O, which is over five times
the size of standard 1500-byte Ethernet frame. Eight KB jumbo frames are supported when running
Ethernet and FCoE I/O concurrently. Jumbo frames can help achieve higher throughput and better CPU
utilization. Jumbo frames are particularly useful for database transfers and tape backups.
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Standard Features
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 3

802.1p QoS Tagging IEEE quality of service (QoS) 802.1p tagging allows the adapter to mark or tag frames with a priority level
across a QoS-aware network for improved traffic flow.
802.1Q VLANs The HP 554M adapter supports the IEEE 802.1Q virtual local area network (VLAN) protocol that allows each
physical port or FlexNIC to be assigned to a VLAN for added network segmentation and enhanced security
and performance. VLANs increase security by isolating traffic between users. Limiting the broadcast traffic
to within the same VLAN domain also improves performance.
Network Adapter
Teaming
The HP 554M adapter support for NIC teaming helps IT administrators increase network fault tolerance and
improve workload balance. These capabilities optimize availability, improve performance and help reduce
costs.
TCP/IP Stateless
Offloading
For overall improved system response, the HP 554M adapter supports standard TCP/IP stateless
offloading techniques including:
TCP/IP checksum offload (TCO) moves the TCP and IP checksum offloading from the CPU to the
network adapter.
Large send offload (LSO), also known as TCP segmentation offload (TSO), allows TCP segmentation
to be handled by the adapter rather than the CPU.
Single-Root I/O
Virtualization
Single-Root I/O Virtualization (SR-IOV) provides a mechanism to bypass the host system hypervisor in
virtual environments providing near metal performance and server efficiency. SR-IOV provides mechanism
to create multiple Virtual Functions (VFs) to share single PCIe resources. The device is capable of SR-IOV,
and requires Server BIOS support, controller firmware, and OS support.
TOE TCP/IP Offload Engine (TOE) moves the processing of data in the TCP protocol stack from the server
CPU to the network card, freeing CPU cycles for other duties.
RDMA Not Supported
iSCSI The HP 554M adapter supports accelerated iSCSI and iSCSI INT 13 Boot.
Warranty HP branded hardware options qualified for BladeSystem c-Class and p-Class servers are covered by a
global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel
Partners. The HP branded hardware option diagnostic support and repair is available for one year from
date of purchase, or the length of the server they are attached to, whichever is greater. Support for
software and initial setup is available for 90 days from date of purchase. Additional support may be
covered under the warranty or available for an additional fee. Enhancements to warranty services are
available through HP Care Pack services or customized service agreements.
Additional information regarding worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Standard Features
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 4

Service and Support HP Technology Services
HP Technology Services offers you consultants and support experts to solve your most complex
infrastructure problems. We help keep your business running, boost availability and avoid downtime.
Protect your business beyond warranty with HP Care Pack Services
When you buy HP Options, it's also a good time to think about what level of service you may need. HP Care
Pack services provide total care and support expertise with committed response choices designed to meet
your IT and business need.
HP Foundation Care services deliver scalable support-packages for HP industry-standard servers and
software. You can choose the type and level of service that is most suitable for your business needs. New
to this portfolio is HP Collaborative Support. If you are running business critical environments, HP offers
Proactive Care or Critical Advantage. These services help you deliver high levels of application availability
through proactive service management and advanced technical response.
Here is the support service recommendation from the Foundation Care and Proactive Care portfolio. For
customized support service solution, HP can work with you to tailor a service solution for your unique
support requirements using broader services portfolio of Foundation Care and Proactive Care.
Recommended Services Recommended HP Care Pack Services for optimal satisfaction with your HP product
3-Year HP 24x7 4 hour Response, Hardware Support Onsite Service
Provides you with rapid remote support and if required an HP authorized representative who will arrive on
site any time and day of the year to begin hardware maintenance service within 4 hours of the service
request being logged.
http://h20195.www2.hp.com/V2/GetPDF.aspx/5982-6547EEE.pdf
OR
3-Year HP 24x7 4 hour Response, HP Collaborative Support
Offers customers a single point of contact for server problem diagnosis, hardware problem resolution, and
basic software problem diagnosis, fault isolation, and resolution if available to HP. If the problem is with
HP HW, the representative will arrive on site any time and day of the year to begin hardware maintenance
service within 4 hours of the service request being logged. In case, the issue is with HP or supported third-
party software product and cannot be resolved by applying known fixes, HP will contact the third-party
vendor and create a problem incident on your behalf.
HP ProLiant Server Hardware Installation
Provides for the basic hardware installation of HP branded servers, storage devices and networking
options to assist you in bringing your new hardware into operation in a timely and professional manner.
http://h20195.www2.hp.com/V2/GetPDF.aspx/5981-9356EN.pdf
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Service and Support
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 5

Related Services Related HP Care Pack Services to enhance your HP product experience
3-Year HP 24x7 4 hour Response, Proactive Care or Critical Advantage
Helps optimize your systems and delivers high levels of application availability through proactive service
management and advanced technical response. A skilled Technical Manager will own your query or issue
end to end until resolved, delivering a single point of contact for you.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA3-2140ENW.pdf
OR
3-Year HP 6-hour Onsite Call-to-Repair, HP Collaborative Support
Offers customers a single point of contact for server problem diagnosis, hardware problem resolution to
return the hardware in operating condition within 6 hours of the initial service request to the HP Global
Solution Center, and basic software problem diagnosis, fault isolation, and resolution if available to HP. In
case, the issue is with HP or supported third-party software product and cannot be resolved by applying
known fixes, HP will contact the third-party vendor and create a problem incident on your behalf.
HP Proactive Select Service
Provides a flexible way to purchase HP best-in-class consultancy and technical services. You can buy
Proactive Select Service Credits when you purchase your hardware and then use the credits over the next
12 months.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA2-3842ENN.pdf
Insight Remote Support Provides 24 X 7 remote monitoring, proactive notifications, and problem resolution. Learn more
http://www.hp.com/go/insightremotesupport
HP Support Center Personalized online support portal with access to information, tools and experts to support HP business
products. Submit support cases online, chat with HP experts, access support resources or collaborate with
peers. Learn more http://www.hp.com/go/hpsc
HP's Support Center Mobile App * allows you to resolve issues yourself or quickly connect to an agent for
live support. Now, you can get access to personalized IT support anywhere, anytime.
HP Insight Remote Support and HP Support Center are available at no additional cost with a HP warranty,
HP Care Pack or HP contractual support agreement.
*HP' Support Center Mobile App is subject to local availability.
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Service and Support
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 6

Parts and materials HP will provide HP-supported replacement parts and materials necessary to maintain the covered
hardware product in operating condition, including parts and materials for available and recommended
engineering improvements. Supplies and consumable parts will not be provided as part of this service;
standard warranty terms and conditions apply. Parts and components that have exceeded their maximum
supported lifetime and/or the maximum usage limitations as set forth in the manufacturer's operating
manual or the technical product data sheet will not be provided, repaired or replaced as part of this service.
Warranty / Service
Coverage
For ProLiant servers and storage systems, this service covers HP-branded hardware options qualified for
the server, purchased at the same time or afterward, internal to the enclosure, as well as external
monitors up to 22" and tower UPS products; these items will be covered at the same service level and for
the same coverage period as the server unless the maximum supported lifetime and/or the maximum
usage limitation has been exceeded. Coverage of the UPS battery is not included; standard warranty terms
and conditions apply.
The defective media retention service feature option applies only to Disk or eligible SSD/Flash Drives
replaced by HP due to malfunction. It does not apply to any exchange of Disk or SSD/Flash Drives that have
not failed. SSD/Flash Drives that are specified by HP as consumable parts and/or that have exceeded
maximum supported lifetime and/or the maximum usage limit as set forth in the manufacturer's operating
manual or the technical data sheet are not eligible for the defective media retention service feature option.
For more information To learn more on services for HP ESSN Options, please contact your HP sales representative or HP
Authorized Channel Partner. Or visit: http://www.hp.com/services/proliant or
www.hp.com/services/bladesystem
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Service and Support
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 7

Additional c-Class
BladeSystem Adapters
FlexibleLOM Adapters
HP FlexFabric 10Gb 2-port 554FLB Adapter 647586-B21
HP Flex-10 10Gb 2-port 530FLB Adapter 656590-B21
Mezzanine Adapters
HP Flex-10 10Gb 2-port 530M Adapter 631884-B21
HP Flex-10 10Gb 2-port 552M Adapter 674764-B21
HP 10Gb
interconnects
HP Virtual Connect Flex-10 10Gb Ethernet Module for c-Class BladeSystem 455880-B21
HP 6125G/XG Ethernet Blade Switch 658250-B21
HP 6120XG Blade Switch 516733-B21
HP 10GbE Ethernet Pass-Thru Module for c-Class BladeSystem 538113-B21
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Related Options
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 8

General Specifications Network processor Emulex BE3
Data rate Two ports, each at 20 Gbps full duplex; 40 Gbps aggregate full duplex
theoretical bandwidth.
Onboard memory 128MB
Bus type PCI Express v2.0 (Gen 2) x8
Form factor Type A Mezzanine Card
IEEE Compliance 802.1p, 802.1q, 802.1qau, 802.3ad, 802.3ae, 802.3ap (10GBase-KX4) and
802.3x
Power and Environmental
Specifications
Operating Temperature 0°C to 55°C / 32°F to 131°F
Humidity 10% to 90% non-condensing
Power requirement 8.6W idle and 10W maximum
Emissions classification FCC Class A
Agency approvals USA FCC (CFR 47 part 15) and UL 60950
Canada ICES-003 and CSA60950
Japan VCCI
Korea MIC (RRL), EMC Registration
Australia ACA, AS/NZS3548/EN55022:1998, EN55024:1998
European Union EN55022:1998 (CISPR 22), EN55024:1998, and
IEC60950:1999 (EN60950:2000)
RoHS Compliance 6 of 6
Safety UL Mark (USA and Canada)
CE Mark
EN 60590
Operating System
Support
Microsoft :
Microsoft Windows Server 2008 SP2, R2 (x86 and x64)
Microsoft Windows Hyper-V, R2 SP1
Linux :
RHEL 5, 6
SLES 10, 11
Solaris :
Solaris 10 (x86 and x64)
Virtualization :
VMware ESX/ESXi 4.1 and ESXi 5.0
NOTE: For more operating system support & certification information, please visit:
http://h10018.www1.hp.com/wwsolutions/index.html .
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Technical Specifications
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 9

Environment-friendly
Products and Approach
End-of-life Management
and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to:
http://www.hp.com/go/green . To recycle your product, please go to:
http://www.hp.com/go/green or contact your nearest HP sales office.
Products returned to HP will be recycled, recovered or disposed of in a
responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide
treatment information for each product type for use by treatment facilities.
This information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green . These instructions may be
used by recyclers and other WEEE treatment facilities as well as HP OEM
customers who integrate and re-sell HP equipment.
© Copyright 2013 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Windows is a US registered trademark of Microsoft Corporation.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
QuickSpecs
HP FlexFabric 10Gb 2-port 554M Adapter
Technical Specifications
DA - 14221 Worldwide — Version 10 — December 7, 2013 Page 10