HP f800g User manual

1
Battery warning
The battery for this car camcorder is sealed internally. DO NOT
attempt to disassemble the camcorder and remove the battery.
Always charge using the provided system. Improper charging of the
battery may result in explosion.
The battery is designed for this camcorder and is not customer
replaceable.
Batteries may explode if exposed to na ed fire. Never expose the
car camcorder in a fire.
Recycle the camcorder observing local regulations.
Notes on Installation
1. Install the device near the rear-view mirror to obtain the best
open-field view. Do NOT install the camcorder in a location that will
obstruct your required driving view.
2. Ma e sure that the lens is within the wiping range of the
windscreen wiper to ensure a clear view even when it rains.
3. Do not touch the lens with your fingers. Finger grease may be left
on the lens and will result in unclear videos or snapshots. Clean the
lens on a regular basis.
4. Do not install the device on a tinted window. Doing so may damage
the tint film.
5. Ma e sure that the installation position is not hindered by the
tinted window.

2
1Introduction
1.1 Package Contents
The pac age contains the following items. In case there is any missing or
damaged item, contact your dealer immediately.
Camcorder Brac et
CD-ROM Quic start guide Car adapter

3
1.2 Product Overview
No. Item No. Item
1 Brac et Soc et 6 GPS Antenna
2 Memory Card Slot 7 Wide Angle Lens
3 Power Switch 8 Spea er
4 LED Indicator 9 Microphone
5 USB / Power Connector 10 LCD Touch Panel
Top and Bottom Views
Side (Left and Right) Views
Front View
Rear View
2
8
9
1
10
4
5
7
6
3

4
2etting Started
2.1 Inserting the Memory Card
Insert memory card with the gold section facing upward and the screen
of the camcorder facing upward too, as illustrated. Push the memory
card in until a clic sound is heard, indicating the card is in position.
To remove the memory card
Push to eject the memory card out of the slot.
Note:
1. Do not remove or insert the memory card when the camcorder is turned on. This
may damage the memory card.
2. Please use a Class 6 or higher rating Micro SD card, max. up to 32GB.
3. Please format the micro SD cards before the initial use.
4. When removing the memory card, be careful that the card may spring out and get
lost. The memory slot has this spring-out feature for easy removal of the card.

5
2.2 Installing in Vehicles
2.2.1 Mount to Windshield
1. Push the brac et into brac et slot on top of
camcorder, until a clic sound is heard.
2. With the suction-cup laying flat,
position the suction-cup on the
windshield.
3. Hold the base firmly on the windshield
and press down the clamp to mount the
car holder to the windshield. Ma e sure
the base is securely loc ed in place.

6
2.2.2 Adjust the Camcorder position
1. Loose the nob to swivel the
camcorder vertically.
2. Loose the nob to swivel the
camcorder horizontally up to
360°.
3. Then tighten the nob to ma e sure the camcorder is securely
loc ed in place.
Knob
Knob

7
2.3 Connecting to Power
Use only the supplied car adapter to power up the camcorder and
charging the built-in battery.
1. Connect one end of car adapter to USB/Power connector port on the
camcorder.
2. Plug the other end of the car adapter to the cigarette lighter soc et
of your vehicle. Once the vehicle engine is started, the camcorder
automatically powers on.
Note:
This product shall be installed near the rear mirror, at the center of windshield, if
possible, for optimal viewing.

8
2.4 Powering the Camcorder On / Off
2.4.1 Auto Power On/Off
Once the vehicle engine is started, the camcorder automatically turns on.
If the Automatic Record function is enabled, the recording will
automatically start right after the camcorder powers on.
2.4.2 Manual Power On/Off and Reset
2.4.2.1 Manual Power On
Slide the power switch and ma e sure that the power switch loc s on the
memory card slot.
On
2.4.2.2 Power Off
The power switch to the edge and ma e sure that the memory slot is
released and the camcorder starts power off sequence. Do not power on
the camcorder when it is in the power-off sequence, or the recorded file
may become corrupt.
O
ff

9
2.5 Initial Settings
Before using the camcorder, we recommend you to enable the
Automatic Record function and set up the correct Date and Time.
2.5.1 Setting the Universal Time Code (UTC)
Depending on your location, you may need to change the current UTC
setting of the camcorder so that the correct date and time are updated
when a GPS signal is detected.
* Be sure to adjust for daylight saving time (DST) by adding +1 hour to the UTC offset.
** These areas may observe half hour increments and daylight saving time (DST).

10
3Using the Car Recorder
3.1 Recording Videos
3.1.1 LDWS (Lane Departure Warning Systems)
When LDWS is enabled after satellite positioning, camcorder will give a
voice alert and display an alarm screen if vehicle speed reaches or
exceeds 50 m/h (31 mile/h) and the vehicle deviates from the original
lane.
To set the LDWS (Lane Departure Warning Systems), do the following:
1. Ensure the camcorder is
connected to the power adapter
and is receiving power.
2. Touch to enter Main
Menu.
3. Touch to switchover to
Driving Safety Main Menu.
4. Touch / to select
for entering LDWS function menu,
then touch again to
enable the function (on).
5. Touch to return to record screen.
6. After enabling LDWS, the screen will display align icon ,
please adjust the camcorder so that the horizontal line and the eye
level are overlapped and the slash lines are centered in the driving
lane. Ma e sure that align icon will not be obscured (e.g. hood)
during installation, it may cause misjudgment if the endpoint is
obscured.

11
Eye Level
Horizon
Vanishing Point
7. When satellite positioning is in ready state, camcorder will give a
voice alert and an alarm screen if vehicle speed reaches or exceeds
50 m/h (31 mile/h) and the vehicle deviates from the original lane.
Note:
1. LDWS is only applicable when satellite positioning is in ready state. Ma e sure
satellite positioning of your camcorder is ready if you want to activate this function.
Satellite positioning function is dependent on the model purchased.
2. When enable the LDWS, please follow this self-aligned approach in order to increase
the accuracy.
3. The all Driving Safety functions such as LDWS, Speed Cam Alert, Speed Limit Alert,
Driver Fatigue Alert and Collision Detection will be disabled, if the product doesn’t
connect with the external power supply.

12
3.1.2 Motion Detection
If Motion Detection is activated, when the camcorder is powered on, a
message “Wait for 10 seconds to enter Motion Detection or touch the
screen to power off” will be displayed on the screen. This means the
system will enter Motion Detection automatically in 10 seconds; when
the camcorder detects any motion in front of lens, Video Record will be
activated for a duration the same as the length setting.
To set the motion detection, do the following:
1. Touch to enter main
menu.
2. Touch to switch over
to Driving Safety Main Menu.
3. Touch / to select
for entering Motion
Detection menu, touch
again to activate (on).
4. Touch to return to record screen.
Note:
1. When the battery is fully charged and is in good condition, Motion Detection can
record continuously for about 30 minutes.
2. As the camcorder is used, the battery storage capacity will decrease gradually. This
is a normal phenomenon for the battery.

13
3.1.3 Emergency Recording
Start the Emergency Recording, do the following:
1. During video recording, touch
to enter emergency
recording mode, the “Emergency”
message will be shown
immediately on the lower left
corner of the screen, and the
recorded file will be protected.
2. Touch again, to halt the recording.
Note:
1. If the Collision Detection function is enabled and a collision is detected, the
camcorder will automatically trigger the emergency recording.
2. The emergency recording file is created as a new file, which will be protected to
avoid being overwritten by normal looping recording. 8G (or above) memory card
can save up to 8 emergency video files. The alert message of “Emergency files are
full” will pop up on the screen when the emergency recording files are full, and the
oldest emergency file will be automatically deleted when a new emergency
recording file is created.

14
3.2 Playing Videos and Viewing Pictures
3.2.1 Playing Videos and Emergency Recording
Playbac video record files as follows:
1. Touch to enter main menu.
2. Touch to switch over to File / Position menu.
3. Touch / to enter Video/
Emergency function menu.
4. Touch / to browse for
required video file, touch selected preview of video to enter
Playbac Mode
5. Touch repetitively to return to Record Screen.

15
3.2.2 Viewing Pictures
View pictures as follows:
1. Touch to enter Main Menu.
2. Touch to switch over to File / Position main menu.
3. Touch to enter Picture
function menu.
4. Touch / to browse for required picture files, touch
selected preview of picture to enter Picture Playbac Mode.
5. Touch repetitively to return Record Screen.

16
3.2.3 Deleting Files
To delete file(s), do the following:
1. Touch to enter Main Menu.
2. Touch to switch over to File / Position main menu.
3. Touch / / to enter Video/Picture/Emergency menu.
4. Touch / to browse for required video or picture file; touch
selected preview image to enter Video/Picture Playback Mode.
5. Touch to enter File Deletion menu, select / to
delete one file or all files; touch / to confirm or cancel
the selection.
Item Description
Delete One Delete the current file.
Delete All Delete all files.
6. Touch repetitively to return to Record Screen.
Note:
Deleted files cannot be recovered. Ensure the files have bac up before deletion.

1
Avertissement sur la batterie
Rechargez toujours avec le système fourni. Une mauvaise gestion
de la batterie peut causer des explosions.
Ne démontez ou percez jamais la batterie, et évitez les
courts circuits.
Les piles peuvent exploser si elles sont exposées à des flammes
nues. Ne jetez jamais les piles au feu.
Jetez les piles usées en respectant les réglementations locales.
Ne remplacez jamais la batterie par vous-même, demandez à
votre revendeur de le faire pour vous.
Remarques au sujet de l'installation
1. Installez l'appareil vers le rétroviseur afin d'obtenir la meilleure
vue.
2. Assurez vous que l'objectif est dans la surface de balayage de
l'essuie glace du pare brise afin de bénéficier d'une vue claire
même lorsqu'il pleut.
3. Ne jamais toucher l'objectif avec vos doigts. Des empreintes de
doigts peuvent rester visibles sur l’objectif et les photos ou les clips
vidéo peuvent ainsi être flous. Nettoyez souvent l'objectif.
4. Ne pas installer l'appareil sur une vitre teintée. Vous risqueriez
d'endommager le film teinté.
5. Assurez vous que la position d'installation n'est pas entravée par la
vitre teintée.

2
1ntroduction
1.1 Contenu de la boîte
Cet emballage contient les éléments suivants. Si l'un de ces éléments est
absent ou endommagé, contactez votre revendeur immédiatement.
Enregistreur de voiture Support
CD ROM Guide de démarrage
rapide Adaptateur de voiture

3
1.2 Présentation du produit
N° Élément N° Élément
1 Emplacement du support 7 Objectif grand angle
2 Fente pour carte mémoire 8 Transmission Wi Fi
3 Bouton d'alimentation 9 Haut parleur
4 Voyant DEL 10 Microphone
5 Connecteur USB /
d'alimentation
11 Écran tactile LCD
6 Antenne GPS
Vue de dessus et de
dessous
Vue de côté
(gauche et droite)
Vue de devant
Vue de derriére
2
8
9
3
10
4
5
7
6
1