HP i2000 Manual

processor installation
hp workstation i2000
Manufacturing Part Number: A6037-90060
Edition: E0801
Printed in U.S.A.

hp workstation i2000
2
TABLE OF CONTENTS
WARNINGS
SAFETY AND REGULATORY REQUIREMENTS
PURPOSE OF THIS GUIDE
1. WORKSTATION INSTRUCTIONS ...................................................................... 10
1.1 accessing the system ..................................................................................... 10
1.2 installing an Itaniumprocessor in an hp workstation i2000 ...................... 15
1.2.1 removing the processor ........................................................................ 15
1.2.2 installing the processor .......................................................................... 17
1.2.3 replacing the power pod...................................................................... 19
1.3 installing a second Itaniumprocessor in a workstation............................ 20
1.4 reassembling your workstation ...................................................................... 20
1.4.1 reinstalling the processor board ........................................................... 20
1.5 workstation support ........................................................................................ 23

hp workstation i2000
3
Figures
Figure 1. Removing the Four- (4) Chassis Screws ................................................ 10
Figure 2. Bezel Interlock Clips................................................................................ 11
Figure 3. Internal System View after Side Door Removal ................................... 12
Figure 4. Power Supply Door in Opened Position ............................................... 13
Figure 5. Processor Power Harness ....................................................................... 14
Figure 6. Processor Assembly Removal................................................................ 14
Figure 7. Processor Assembly ................................................................................ 15
Figure 8. Removing the Power Pod...................................................................... 16
Figure 9. Removing the Processor ........................................................................ 16
Figure 10. Replacing the Processor ...................................................................... 17
Figure 11. Properly Seating the Processor............................................................ 18
Figure 12. Top View of Processor and Cross-Torque Pattern ............................. 18
Figure 13. Installing the Power Pod....................................................................... 19
Figure 14. Correct Reinstallation of E-PAC........................................................... 21
Figure 15. E-PAC Inserted over Memory Cards................................................... 21
Figure 16. E-PAC Installation.................................................................................. 22
Figure 17. Power Supply Door Locking Tab ......................................................... 23

hp workstation i2000
4

hp workstation i2000
5
WARNING!
Please read all warnings and instructions BEFORE operating the system. Avoid Injury: To avoid
personal injury when unpacking the system, use only a mechanical assist unit to lift it off the
shipping pallet. The system weighs approximately 84 lbs.
WARNINGS
The following cautionary notices apply whenever you remove the access cover to access components inside
the system. Before you proceed, please read the following Warning section carefully.
The power supply in this product contains no user-serviceable parts. Refer
servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact
type required.
The DC push-button on/off switch on the system does not turn off system AC
power. To remove AC power from the system, you must unplug each AC power
cord from the wall outlet or power supply.
SAFETY STEPS: Whenever you remove the chassis covers to access the inside
of the system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by using the push-button on/off power switch on the system.
3. Unplug all AC power cords from the system or from wall outlets.
4. Label and disconnect all cables connected to the I/O connectors or ports on the
rear of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an anti-static
wrist strap attached to chassis ground of the system—any unpainted metal
surface—when handling components.
6. Do not operate the system with the chassis covers removed.
After you have completed the six SAFETY steps above, you can remove the
system covers. To do this:
1. Unlock the system from the side using the keys provided.
2. Remove the thumbscrews to remove the side cover.
Continued

hp workstation i2000
6
WARNINGS (continued)
For proper cooling and airflow, always reinstall the chassis covers before turning on
the system. Operating the system without the covers in place can damage system
parts. To install the covers:
1. Check first to make sure you have not left loose tools or parts inside the system.
2. Check that cables, add-in boards, and other components are properly installed.
3. Attach the covers to the chassis with the screws removed earlier, and tighten
them firmly.
4. Lock the system to prevent unauthorized access inside the system.
5. Connect all external cables and the AC power cord to the system.
The microprocessor, heat sink and Power Pod may be hot if the system has been
running. Also, there may be sharp pins and edges on some board and chassis
parts. Contact should be made with care. Consider wearing protective gloves.
Danger of explosion if the battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the equipment manufacturer. Discard
used batteries according to manufacturer’s instructions.
The system is designed to operate in a typical office environment. Choose a site
that is:
1. Clean and free of airborne particles (other than normal room dust).
2. Well ventilated and away from sources of heat including direct sunlight.
3. Away from sources of vibration or physical shock.
4. Isolated from strong electromagnetic fields produced by electrical devices.
5. In regions that are susceptible to electrical storms, we recommend you plug your
system into a surge suppresser and disconnect telecommunication lines to your
system during an electrical storm.
6. Provided with a properly grounded wall outlet.
7. Provided with sufficient space to access the power supply cords, because they
serve as the product’s main power disconnect.

hp workstation i2000
7
WARNING
Do not open the power supply. Risk of electric shock. Refer servicing
of the power supply to qualified service personnel.
CAUTION
Before removing the access cover for any reason, observe these
cautionary guidelines.
• Turn off all peripheral devices.
• Turn off the system by pressing the power button on the front of the chassis. Then
unplug the AC power cord from the chassis or wall outlet.
• Label and disconnect all peripheral cables connected to the I/O connectors or
ports on the back of the chassis.
• Provide some electrostatic discharge (ESD) protection by wearing an anti-static
wrist strap attached to chassis ground—any unpainted metal surface—when
handling components.
CAUTION
The power button on the front panel does not disconnect the AC power.
To remove power from the system, you must unplug the AC power cord
from the AC supply or from the computer chassis.
CAUTION
ESD can damage disk drives, boards, and other parts. Perform all
procedures in this chapter only at an ESD workstation. If one is not
available, provide some ESD protection by wearing an anti-static wrist
strap attached to chassis ground
 any unpainted metal surface  on
your system when handling parts.
Always handle boards carefully. They can be extremely sensitive to
ESD. Hold boards only by their edges. Do not touch the connector
contacts. After removing a board from its protective wrapper or from the
system, place the board component side up on a grounded, static free

hp workstation i2000
8
surface. If you place the board on a conductive surface, the battery
leads may short out. If they do, this will result in a loss of CMOS data
and will drain the battery. Use a conductive foam pad if available but
not the board wrapper. Do not slide the board over any surface. For
proper cooling and airflow, always install the chassis side cover before
turning on the system. Operating it without the cover in place can
damage system parts.
safety and regulatory requirements
Read all instructions before using the system. Save all the safety and regulatory instructions. The
Federal Communications Commission at the time of distribution has not approved this
workstation.
This product is not, and may not be, offered for sale or lease, or sold until the written approval of
the FCC and Product Safety Certification have been obtained.

hp workstation i2000
9
purpose of this guide
The purpose of this guide is to provide detailed instructions on installing an Itanium
processor (for replacement or adding a second processor) in an hp workstation i2000.
Each section is intended to build on the previous section and should be preformed in the
order listed. If this kit is used in conjunction with another upgrade kit, the instructions
following the Removing the Processor section may overlap. Please read all instructions
prior to beginning any upgrade.
This processor kit contains:
• One- (1) Itaniumprocessor
• One- (1) heat sink (attached to processor)
.

hp workstation i2000
10
1. workstation instructions
1.1 accessing the system
NOTE
Due to the weight of the workstation system (approximately 84 lbs.), care must
be taken when maneuvering the system during assembly and disassembly.
CAUTION
The DC push-button on/off switch on the system does not completely turn off system AC power.
To remove AC power from the system, you must unplug each AC power cord from the wall outlet
or power supply.
Before servicing, first identify the component(s) that must be added or removed from the
system. If replacing components, such as hard drives, CD-ROMs, or the LS-120 floppy
drive, the front bezel (large plastic section on the front of the system) must be removed
for access to the bays, as well as side access within the system. In cases not involving the
peripherals or front panel ports, the bezel can remain in place. Use the following steps to
access or open the system:
1. Starting with the system in an upright (normal) position, and resting on an anti-
static surface, loosen the four- (4) Phillips-head screws from the rear (as shown in
Figure 1).
Figure 1. Removing the Four- (4) Chassis Screws