HP Kayak XA05 User manual

HP Kayak XA
PC Workstation
User’s Guide
ashaki.bk : cover.fb4 Page 1 Wednesday, July 15, 1998 6:13 PM

Notice
The information contained in this document is subject to change without
notice.
Hewlett-Packard makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. Hewlett-Packard shall not be liable for errors
contained herein or for incidental or consequential damages in connection with
the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written
consent of Hewlett-Packard Company.
Adobe® Reader © 1987-1997 Adobe Systems Incorporated. All rights reserved.
AdobeTM and AcrobatTM are trademarks of Adobe Systems Incorporated.
CompuServe® is a registered trademark of CompuServe Incorporated.
Labtec® is a registered trademark of Labtec Enterprises, Inc.
Matrox® is registered trademark of Matrox electronic Systems Ltd.
MGATM is a trademark of Matrox Graphics, Inc.
Microsoft®, MS®, MS-DOS®, Windows®, and Windows NT® are U.S.
registered trademarks of Microsoft Corporation.
Netscape® is a trademark of Netscape Communications Corporation.
PentiumTM is a trademark of Intel Corporation.
SoundBlasterTM is a trademark of Creative Technology Limited.
Hewlett-Packard France
Performance Desktop Computing Operation
38053 Grenoble Cedex 9
France
1998 Hewlett-Packard Company
ashaki.bk : notice.fb4 Page ii Wednesday, July 15, 1998 6:13 PM

User’s Guide
ashaki.bk : title.fb4 Page iii Wednesday, July 15, 1998 6:13 PM

iv English
Who This Manual Is For
This manual is for anyone who wants to:
•Set up the PC Workstation for the first time.
•Configure the PC Workstation.
•Add accessories to the PC Workstation.
•Troubleshoot problems on the PC Workstation.
•Find out where to get more information and support.
Important Safety Information
WARNING If you have any doubt that you can lift the PC Workstation or display
safely, do not try to move it without help.
For your safety, always connect the equipment to a grounded wall
outlet. Always use a power cord with a properly grounded plug, such as
the one provided with this equipment, or one in compliance with your
national regulations. This PC Workstation is disconnected from the
power by removing the power cord from the power outlet. This means
the PC Workstation must be located close to a power outlet that is easily
accessible.
For your safety, never remove the PC Workstation’s cover without first
removing the power cord from the power outlet, and any connection to
a telecommunications network. Always replace the cover on the
PC Workstation before switching it on again.
To avoid electric shock, do not open the power supply. There are no
user-serviceable parts inside.
To avoid electric shock and harm from to your eyes by laser light, do not
open the laser module. The laser module should be serviced by service
personnel only. Do not attempt to make any adjustment to the laser
unit. refer to the label on the CD-ROM for power requirements and
wavelength. This product is a class 1 laser product.
ashaki.bk : title.fb4 Page iv Wednesday, July 15, 1998 6:13 PM

English v
Important Ergonomic Information
It is strongly recommended that you read the ergonomic information
before using your PC Workstation. If you are using Windows NT 4.0,
open the Start menu in the task bar and select Programs-HP Info.
Then double-click the help topic “Working in Comfort”.
ashaki.bk : title.fb4 Page v Wednesday, July 15, 1998 6:13 PM

vi English
ashaki.bk : title.fb4 Page vi Wednesday, July 15, 1998 6:13 PM

Contents
English vii
1 Setting Up and Using Your HP PC Workstation . . . . . . . . . . . . . 1
2 How to Install Accessories In Your HP PC Workstation . . . . . 21
3 Troubleshooting Your HP PC Workstation . . . . . . . . . . . . . . . . 29
4 Hewlett Packard Support and Information Services. . . . . . . . 41
Regulatory Information and Warranty . . . . . . . . . . . . . . . . . . . 49
ashaki.bk : ashaki.toc Page vii Wednesday, July 15, 1998 6:13 PM

viii English
ashaki.bk : ashaki.toc Page viii Wednesday, July 15, 1998 6:13 PM

1
Setting Up and Using Your HP
PC Workstation
ashaki.bk : ashak-1.fb4 Page 1 Wednesday, July 15, 1998 6:13 PM

1 Setting Up and Using Your HP PC Workstation
Unpacking Your Kayak PC Workstation
2English
Unpacking Your Kayak PC Workstation
WARNING If you are in any doubt that you can lift the PC Workstation and the
display safely, do not try to move them without help.
1When you receive your PC Workstation, unpack all of the
components.
NOTE Device drivers and HP utilities are preloaded on your system and
provided on a Drivers, Utilities and Documentation CD-ROM. This
CD-ROM also includes tips for re-installing the operating system.
2Place the PC Workstation on a sturdy desk with easily accessible
power outlets and enough space for the keyboard, mouse, and any
other accessories.
3Position the PC Workstation so that its rear connectors are easily
accessible.
Installation Tools No tools are required to install your PC Workstation. However, if you
plan to install a disk drive or an accessory board inside your
PC Workstation, you will need a flat-blade screwdriver. For more
information on installing accessories, refer to "How to Install
Accessories In Your HP PC Workstation", on page 19.
ashaki.bk : ashak-1.fb4 Page 2 Wednesday, July 15, 1998 6:13 PM

English 3
1 Setting Up and Using Your HP PC Workstation
Connecting the Mouse, Keyboard, Display and Printer
Connecting the Mouse, Keyboard, Display and Printer
Connect the mouse, keyboard, and display to the back of the
PC workstation. The connectors are shaped to go in one way only.
Tighten the display cable attachment screws.
NOTE The Universal Serial Bus (USB) connectors can be used for USB
accessories. Most USB accessories are automatically configured as soon
as they are physically attached to the PC Workstation. USB accessories
are not supported by all operating systems.
Mouse Connector (lower)
2 USB Connectors
(refer to note below)
Serial Port A
Parallel Connector
Display Connector
Keyboard Connector (upper)
Serial Port B
ashaki.bk : ashak-1.fb4 Page 3 Wednesday, July 15, 1998 6:13 PM

1 Setting Up and Using Your HP PC Workstation
Connecting to a Network (Selected Models Only)
4English
Connecting to a Network (Selected Models Only)
Your PC Workstation may be equipped with a 10BT/100TX LAN
interface adapter.
The LAN adapter supports both 10 Mbit/s and 100 Mbit/s operations
and automatically detects which network type is being used.
1Connect the RJ-45 plug on your network cable to the LAN connector
on your LAN PC Workstation Adapter. Push the plug into the
connector until the plug clicks into place.
2Attach the other end of the LAN cable to a hub (or into a wall socket
that is connected to a hub).
Let your network administrator know that you are connecting your
PC Workstation to the network.
For further instructions on configuring your network connection,
refer to the Upgrade and Configuration Guide available on HP’s
Web site.
Refer also to the online Network Administrator’s Guide
(downloadable from HP’s Web site) for further instructions on
setting up your PC Workstation for a LAN connection.
ashaki.bk : ashak-1.fb4 Page 4 Wednesday, July 15, 1998 6:13 PM

English 5
1 Setting Up and Using Your HP PC Workstation
Connecting Audio Accessories
Connecting Audio Accessories
Your PC Workstation has a Headphone Out jack and a Microphone In
jack on the Audio Front Panel. A LINE IN jack, LINE OUT jack, MIC IN
jack, and MIDI/Joystick connector are located on the backplate of the
audio board.
Audio Front Panel
NOTE
The internal speaker and LINE OUT
jack on the audio board backplate
are deactivated when you use the
Headphones jack on the Audio
Front Panel.
The internal speaker is deactivated
when you use the LINE OUT jack.
External speakers should have a
built-in power supply.
The audio accessories shown
here (microphone, speakers, and
audio system) are not supplied
with your PC Workstation.
Volume can be controlled through
the HP enhanced keyboard or the
software volume control.
Audio board
backplate
ashaki.bk : ashak-1.fb4 Page 5 Wednesday, July 15, 1998 6:13 PM

1 Setting Up and Using Your HP PC Workstation
Connecting an External SCSI Accessory (Selected Models Only)
6English
WARNING To avoid discomfort from unexpected noise or static, always turn
down the volume before connecting headphones or speakers.
Listening to loud sounds for prolonged periods may permanently
damage your hearing.
Before putting on headphones, place them around your neck and turn
down the volume. When you put on the headphones, slowly increase
the volume until you find a comfortable listening level, then leave the
volume control in that position.
Connecting an External SCSI Accessory
(Selected Models Only)
An external SCSI device is connected as follows:
1You should assign an unused SCSI ID to the accessory. SCSI IDs
range from 0 to 15 for wide 16-bit SCSI. The SCSI ID 0 is reserved for
the first SCSI hard disk drive and SCSI ID 7 is reserved for SCSI
controller (the default for narrow and wide SCSI devices).
Refer to the manual provided with the SCSI accessory for
instructions on selecting a SCSI ID.
NOTE You don’t need to set a SCSI ID for Plug and Play SCSI devices (SCSI
devices which support the SCAM protocol).
Windows 98 does not support SCAM.
2Make sure the SCSI accessory is terminated correctly—either
internally or by a terminating resistor (refer to the manual provided
with the SCSI accessory).
ashaki.bk : ashak-1.fb4 Page 6 Wednesday, July 15, 1998 6:13 PM

English 7
1 Setting Up and Using Your HP PC Workstation
Connecting an External SCSI Accessory (Selected Models Only)
3Connect the SCSI accessory to your PC Workstation’s external 16-bit
SCSI connector with a shielded SCSI cable.
4Refer to the manual provided with the SCSI accessory to learn how
to install any software that may be necessary to use it.
NOTE The total length of the external SCSI cables should not exceed 3 meters
(approximately 10 feet).
ashaki.bk : ashak-1.fb4 Page 7 Wednesday, July 15, 1998 6:13 PM

1 Setting Up and Using Your HP PC Workstation
Connecting the Power Cords
8English
Connecting the Power Cords
1Remove any warning labels that may be covering the computer’s
power connector on the rear of the computer.
2Connect the power cords to the display and the computer. (The
connectors are shaped to go in one way only.)
NOTE On some PC Workstation models, the voltage is selected automatically.
If your PC Workstation has a voltage selection switch, make sure it is set
correctly.
3Connect the display’s power cord and the computer’s power cord to
grounded outlets.
Display Power Connector
PC Workstation
Power Connector
Grounded Outlet
ashaki.bk : ashak-1.fb4 Page 8 Wednesday, July 15, 1998 6:13 PM

English 9
1 Setting Up and Using Your HP PC Workstation
Connecting the Power Cords
WARNING For your safety, always connect the equipment to a grounded wall
outlet. Always use a power cord with a properly grounded plug, such
as the one provided with this equipment, or one in compliance with
your national regulations. This PC Workstation is disconnected from
the power by removing the power cord from the power outlet. This
means the PC Workstation must be located close to a power outlet that
is easily accessible.
ashaki.bk : ashak-1.fb4 Page 9 Wednesday, July 15, 1998 6:13 PM

1 Setting Up and Using Your HP PC Workstation
The MaxiLife Control Panel
10 English
The MaxiLife Control Panel
The MaxiLife panel is located on the front of your PC Workstation.
HP MaxiLife and its
Liquid Crystal Display
(LCD)
HP MaxiLife and its LCD helps you diagnose problems with your PC
Workstation and provides system information you may need to obtain
support. Press one of the LCD control buttons to display the menu. Use
to scroll through the menu items and to select the item
required. For more information on using the LCD, refer to “Using HP
MaxiLife to Diagnose Problems” on page 28.
PC Lock Button With HP Lock installed, you can use this button to prevent
unauthorized access of your PC Workstation during your absence. Your
applications will remain active. To unlock the PC Workstation, enter
the Windows login password (refer to Windows Help in the Start
menu to set or change this password).
Network Activity Light This light glows/flickers when your PC Workstation is accessing
the network.
Hard Disk Activity Light This light glows/flickers when your hard disk drive is being accessed.
Power On/Off
Button and LED
PC Lock Button and LED
Network Activity Light
Hard Disk Activity Light
Reset Button
LCD Control Buttons
ashaki.bk : ashak-1.fb4 Page 10 Wednesday, July 15, 1998 6:13 PM

English 11
1 Setting Up and Using Your HP PC Workstation
Starting and Stopping Your PC Workstation
Starting and Stopping Your PC Workstation
Starting Your PC Workstation for the First Time
If your PC Workstation has preinstalled software, it is initialized the
first time you start the PC Workstation. The software initialization
process takes a few minutes. This process sets up the software in your
language and sets up your software to use the hardware installed in
your computer (you can change the settings after the software has
been initialized).
Starting Your PC Workstation
1Before you start your PC Workstation, first switch on the display.
2Start your PC Workstation in one of these ways:
•Press the power button on the front panel.
•Press the keyboard space bar.
The keyboard power-on feature will work only if Space-bar is
enabled in thePower menu of the Setup program (refer to page 39)
and the appropriate system board switch is DOWN (the default
setting).
When you switch on the computer, it carries out the Power-On-Self-
Test (POST) while the PC Workstation’s logo is displayed. If you
wish to view the details of this test, press . If there is an error in
the POST, the error will automatically be displayed.
3If you have set a password in the PC Workstation’s Setup program,
the password prompt displays after the POST has completed. If the
Password prompt is displayed, type your password and press
to be able to use the PC Workstation.
Initializing Your Software
NOTE Do NOT switch OFF the PC Workstation while the software is being
initialized—this could cause unexpected results.
ashaki.bk : ashak-1.fb4 Page 11 Wednesday, July 15, 1998 6:13 PM

1 Setting Up and Using Your HP PC Workstation
Starting and Stopping Your PC Workstation
12 English
To initialize your software:
1Turn on the display first, and then the PC Workstation.
When the PC Workstation is switched on, the HP PC Workstation’s
logo is displayed. The PC Workstation performs a Power-On-Self-
Test (POST).
2The software initialization process starts. It displays the software
license agreement, gives you an opportunity to read Working in
Comfort (ergonomic advice for computer users), and then asks
questions about the PC Workstation.
3While the initialization process is running, you can complete the
Warranty Registration card that came with this manual.
4When the initialization process has finished, click OK and the
PC Workstation will restart.
Creating an Emergency Repair Disk
During the initialization of your software, it is very important that you
create an Emergency Repair Disk for the operating system, when
prompted. HP recommends that you use new diskettes for this
purpose.
For more information on how to create these diskettes, refer to the
documentation that came with your application software or operating
system.
Stopping Your PC Workstation
To stop the PC Workstation, first make sure that you have exited all
applications and then use your operating system’s shutdown command
in the Start menu. When prompted, press the power button on your
PC Workstation’s control panel.
CAUTION Do not use the power button until prompted to do so as you may lose
any unsaved data from open applications.
ashaki.bk : ashak-1.fb4 Page 12 Wednesday, July 15, 1998 6:13 PM