HP Z600 - Workstation - 6 GB RAM User manual

Diskette drive installation
Introduction
This document describes how to install a diskette drive in an HP series Workstation.
Kit contents
●Diskette drive
●Optical bay drive carrier
●Cables
●Four M3 guide screws (for HP 400 Workstations)
Before you begin
To view QuickSpecs and determine the compatibility of this product with your HP workstation, see
http://www.hp.com/go/productbulletin.
© 2009 Hewlett-Packard Development Company, L.P.
ENWW Introduction 1

Warnings and cautions
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence
of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed
area marked with this symbol.
WARNING! To reduce the risk of electric shock or damage to your equipment:
— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence
of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce
the risk of injury from a hot component, enable the surface to cool before touching.
WARNING! If a product is shipped in packaging marked with this symbol, , the product must always
be lifted by two persons to avoid personal injury due to product weight.
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
workstation setup, posture, health, and work habits for computer users, and provides important electrical
and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the
documentation CD (if one is included with the product).
CAUTION: Static electricity can damage the electronic components of the workstation. Before
beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal
object.
CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge
(ESD) precautions while performing the system parts removal and replacement procedures:
— Work on a static-free mat.
— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body
to the ground.
— Create a common ground for the equipment you are working on by connecting the static-free mat,
static strap, and peripheral units to that piece of equipment.
NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested
for reliability and are manufactured to high quality standards.
2 Diskette drive installation ENWW

Step 1—Preparing for component installation
NOTE: Workstation models vary. All illustrations are examples only.
Accessing the internal components of the workstation
1. If you need help preparing the workstation for this installation, consult the removal and replacement
procedures in the service guide for your workstation at http://www.hp.com/support/
workstation_manuals.
NOTE: For the HP Workstation series, these procedures are also available in the User
Guide on the Documentation and Diagnostics CD that shipped with your workstation.
2. Power down the workstation, and then disconnect the power cord.
3. Power down all external devices, and then disconnect them from the workstation.
4. Remove the side access panel.
Removing components
1. If present, remove the airflow guide to enable access to the optical bay and system board
connectors.
2. Remove the front bezel if applicable.
NOTE: The front bezel does not need to be removed on HP 600 and HP 800 Workstations.
3. Remove the filler from the lowest available optical drive bay.
Step 2—Installing the diskette drive
1. For HP 400 Workstations, install four black M3 guide screws in the four lower holes on the carrier.
Figure 1 Installing guide screws in the carrier for HP 400 Workstations
2. To install the diskette drive in the optical bay carrier:
a. Leave the four preinstalled guide screws in the lower holes of the diskette drive in place.
b. Use the four guide screws to align the diskette drive with the carrier .
ENWW Step 1—Preparing for component installation 3

c. Lower the diskette drive into the carrier
2
.
Figure 2 Installing the diskette drive in the optical bay drive carrier
d. Align the rear screws on the drive with the channel in the carrier .
e. To fully seat the diskette drive in the carrier, the carrier cannot be in contact with a solid
surface. Lift the carrier up as you slide the drive forward .
f. The green carrier latch snaps into place when fully seated.
Figure 3 Installing the diskette drive in the optical bay drive carrier
4 Diskette drive installation ENWW

3. To install the drive carrier and diskette drive, disengage the optical bay release latch while
inserting the carrier into the optical drive bay
2
.
Figure 4 Installing the carrier in the optical bay
4. Slide the carrier into the bay. Release the latch just before the carrier is fully seated, to enable the
latch pins to engage.
Step 3—Configuring the cabling
NOTE: To locate connectors on the system board, see to the service label on the side access panel.
1. Locate the optical drive power supply cable, and then attach the end connector to the diskette drive
.
2. Select the diskette drive data cable that best fits the hardware configuration of the workstation, and
then connect one end to the hard drive
2
.
Figure 5 Diskette power and data connections
3. Connect the other end of the data cable to the system board.
CAUTION: The cable must stay between the system board and the hard drive cage to avoid
interfering with the heatsink fans and airflow.
ENWW Step 3—Configuring the cabling 5

4. Gently push the cable down to keep it off the system board. .
Figure 6 Routing the diskette data cable
Step 4—Reassembling the workstation
1. Reinstall the bezel, if applicable.
2. Reinstall the airflow guide, if applicable.
3. Reinstall the side access panel.
4. Reconnect power to the workstation and all external devices.
5. Restore power to the workstation and all external devices.
Japanese 日本語
This document is available in Japanese. See http://www.hp.com/support/workstation_manuals, then
select your workstation product and select Japanese from the drop down Manual Language menu.
このドキュメントは日本語版が用意されています。http://www.hp.com/support/workstation_manuals
にアクセスし、ご使用のワークステーション製品を選択し、Manual Language ドロップダウン メニ
ューから Japanese を選択してください。
6 Diskette drive installation ENWW