HP StorageWorks director 2/64 User manual

hp StorageWorks
universal port module kit
installation instructions
Part Number:AA–RSS2B–TE/958-000281-000
Second Edition (November 2002)
These installation instructionsprovide procedures forsetting up,
configuring, and managing a UPM kit in an HP StorageWorks
Director2/64 ora Director2/140.

© Hewlett-Packard Company, 2002. All rights reserved.
Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information, which is protected by copyright. No part of this
document may be photocopied, reproduced, or translated into another language without the prior
written consent of Hewlett-Packard. The information contained in this document is subject to change
without notice.
All other product names mentioned herein may be trademarks of their respective companies.
Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained
herein. The information is provided “as is” without warranty of any kind and is subject to change
without notice. The warranties for Hewlett-Packard Company products are set forth in the express
limited warranty statements accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
Printed in the U.S.A.
universal port module kit installation instructions
Second Edition (November 2002)
Part Number: AA–RSS2B–TE

universal port module kit installation instructions iii
Contents
About this Guide
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Symbols in Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Symbols on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Rack Stability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Getting Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
HP Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
HP Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
HP Authorized Reseller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Installation Instructions
Supported Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installing the UPM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Procedural Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ESD Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Removing the UPM Filler Blank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the UPM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Miscellaneous Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
External Loopback Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Unblocking a UPM Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

vuniversal port module kit installation instructions
About this Guide
These installation instructions provides information to help you:
• Install the UPM kit.
• Test the UPM kit for proper operation.
• Contact technical support for additional assistance.
Intended Audience
This book is intended for use by owners of the hp StorageWorks director 2/64 or the
director 2/140.
Document Conventions
The conventions included in Table 1 apply.
Table 1: Document Conventions
Element Convention
Cross-reference links Blue text: Figure 1
Key names, menu items, buttons, and
dialog box titles Bold
File names, application names, and text
emphasis Italics
User input, command names, system
responses (output and messages) Monospace font
COMMAND NAMES are uppercase
unless they are case sensitive
Variables Monospace, italic font
Website addresses Sans serif font (http://thenew.hp.com)

About this Guide
vi universal port module kit installation instructions
Symbols in Text
These symbols may be found in the text of this guide. They have the following
meanings.
WARNING: Text set off in this manner indicates that failure to follow directions
in the warning could result in bodily harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could
result in damage to equipment or data.
IMPORTANT: Text set off in this manner presents clarifying information or specific instructions.
NOTE: Text set off in this manner presents commentary, sidelights, or interesting points of
information.
Symbols on Equipment
Any enclosed surface or area of the equipment marked with these
symbols indicates the presence of electrical shock hazards. Enclosed
area contains no operator serviceable parts.
WARNING: To reduce the risk of injury from electrical shock hazards, do
not open this enclosure.
Any RJ-45 receptacle marked with these symbols indicates a network
interface connection.
WARNING: To reduce the risk of electrical shock, fire, or damage to the
equipment, do not plug telephone or telecommunications connectorsinto
this receptacle.

About this Guide
viiuniversal port module kit installation instructions
Any surface or area of the equipment marked with these symbols
indicates the presence of a hot surface or hot component. Contact with
this surface could result in injury.
WARNING: To reduce the risk of injury from a hot component, allow the
surface to cool before touching.
Power supplies or systems marked with these symbols indicate the
presence of multiple sources of power.
WARNING: To reduce the risk of injury from electrical shock,
remove all power cords to completely disconnect power from the
power supplies and systems.
Any product or assembly marked with these symbols indicates that the
component exceeds the recommended weight for one individual to
handle safely.
WARNING: To reduce the risk of personal injury or damage to the
equipment, observe local occupational health and safety requirements
and guidelines for manually handling material.
Rack Stability
WARNING: To reduce the risk of personal injury or damage to the equipment, be
sure that:
• The leveling jacks are extended to the floor.
• The full weight of the rack rests on the leveling jacks.
• In single rack installations, the stabilizing feet are attached to the rack.
• In multiple rack installations, the racks are coupled.
• Only one rack component is extended at any time. A rack may become
unstable if more than one rack component is extended for any reason.

About this Guide
viii universal port module kit installation instructions
Getting Help
If you still have a question after reading this guide, contact an HP authorized service
provider or access our website: http://thenew.hp.com.
HP Technical Support
In North America, call technical support at 1-800-652-6672, available 24 hours a day,
7 days a week.
NOTE: For continuous quality improvement, calls may be recorded or monitored.
Outside North America, call technical support at the nearest location. Telephone
numbers for worldwide technical support are listed on the HP website under support:
http://thenew.hp.com/country/us/eng/support.html.
Be sure to have the following information available before calling:
• Technical support registration number (if applicable)
• Product serial numbers
• Product model names and numbers
• Applicable error messages
• Operating system type and revision level
• Detailed, specific questions
HP Website
The HP website has the latest information on this product, as well as the latest drivers.
Access storage at: http://thenew.hp.com/country/us/eng/prodserv/storage.html. From this
website, select the appropriate product or solution.
HP Authorized Reseller
For the name of your nearest HP Authorized Reseller:
• In the United States, call 1-800-345-1518
• In Canada, call 1-800-263-5868
• Elsewhere, see the HP website for locations and telephone numbers:
http://thenew.hp.com.

1universal port module kit installation instructions
Installation Instructions
This chapter describes the procedures used for installing a Universal Port Module
(UPM) kit into a Director 2/64 or a Director 2/140. For each UPM kit tobeinstalled,
perform the following procedures to:
• Remove the UPM filler blank
• Install the UPM
Supported Kits
HP sells the StorageWorks Director 2/64with abase configuration of 32Fibre Channel
ports and the StorageWorksDirector 2/140 witha base configuration of 64 Fibre
Channel ports. HP also sells optional kits to increase the number of ports to a
maximum of 64for the Director 2/64 and a maximum of140 for the Director 2/140.
Use the procedures described in this chapter for the following director UPM kits:
• 8-Port UPM Kit, 300833-B21 (A6574B)
— (2) Short-wave-4-Port cards, includes (8) short-wave 2 Gbps SFP optical
transceivers
— (1) Loop back plug (multi-mode/short wave)
— (1) Port card installation instructions
— (1) Warranty
• 4-Port UPM Kit, 286808-B21
— (1) Short-wave-4-Port card, includes (4) short-wave 2 Gbps SFP optical
transceivers
— (1) Loop back plug (multi-mode/short wave)
— (1) Port card installation instructions
— (1) Warranty

Installation Instructions
2universal port module kit installation instructions
Installing the UPM
This section describes procedures to install one UPM card, even though you can
install more than one UPM card at the same time. If you are installing more than one
UPM card, ensure that the procedure steps are applied to all UPM cards being
installed. In addition, this section provides procedural notes and ESD information.
Procedural Notes
The following procedural notes are referenced as applicable. The notes do not
necessarily apply to all procedures in the chapter.
• When performing procedures described in this chapter, follow all electrostatic
discharge (ESD) procedures, WARNING and CAUTION statements, and
statements listed in the preface of this manual.
• After completing the steps of a detailed procedure that is referenced from another
procedure, return to the initial (referencing) procedure and continue to the next
step of that procedure.
ESD Information
When performing procedures described in this section, follow all ESD procedures,
WARNING statements, and CAUTION statements. When installing UPMs, always
connect a grounding cable to the director chassis and wear an ESD wrist strap.
CAUTION: To avoid causing machine errors or damage while working on the director,
follow ESD procedures by connecting a grounding cable to the director chassis and
wearing an ESD wrist strap.
As shown in Figure 1, the ESD grounding point for the front of the Director 2/64
chassis is located at the bottom center, adjacent to the left power supply. As shown in
Figure 2, the ESD grounding points for the front ofthe Director 2/140 chassisare
located are located at the right and left sides of the chassis.
Touch the chassis once before performing any maintenance action, and once each
minute while installing UPMs. If the director is not connected to facility power (and
therefore not grounded), connect the ESD wrist strap to an approved bench grounding
point instead of the chassis.