HP D7171A - NetServer - LPr User manual

Notice
The information contained in this document is subject to change
without notice.
Hewlett-Packard makes no warranty of anykind with
regard to this material, including, but not limited to, the
implied warranties of merchantability and fitness for a
particular purpose. Hewlett-Packard shall not be liable for
errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnishedby
Hewlett-Packard.
This document contains proprietary information that is protected
by copyright.All rights are reserved. No part of this document
may be photocopied, reproduced, or translated to another
language without the prior written consent of Hewlett-Packard
Company.
Hewlett-PackardCompany
Network Server Division
P.O. Box 58059, Technical Marketing
Santa Clara, CA 95052-8059 USA
© Copyright 1996, Hewlett-Packard Company
Road Map contains
Hardware installation steps
Instructions for accessing Navigator CD Release
History
HP NetServer Navigator CD-ROM contains
Readme file
Configuration Assistant: automated or custom
EISA Configuration Utility
JetSet Utility (for setting up the disk array)
Creation of a diskette with Network Operating
System (NOS) hardware drivers
Creation of a hard disk partition for utilities
ISA board installation
Information Assistant containing complete HP
NetServer user and service documentation
contains
Instructions for accessing your HP NetServer
documentation
UPS software installation steps
Hot Swap Subsystem configuration
Troubleshootingand getting help
Warrantyand regulatory information
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
HP NetServer LH Pro User Guide
5965-2309
Printed on recycled paper.
Contents of Navigator Kit
System Installation Overview
!
!
!
Verifycontents
Ensure that your software is the latest revision
View the Readme File
Install all accessories except ISA boards
Configure your HP NetServer
Create a diskette with HP NOS drivers
!
!Copy HP NOS Installation Instructions to a
DOS-formatted diskette for printing
View HP NOS Installation Instructions
Install your Network Operating System with
HP-supplied drivers
Install server management software using
NetServer Assistant Installation Guide
Install UPS software using the HP NetServer
User GuidePro
HP Drivers Diskette is created byHP
ConfigurationAssistant
HP NetServer Assistant Installation Guide
contains instructions for installing server
management software
N
a
v
i
g
a
t
o
r
N
a
v
i
g
a
t
o
r
Install Hardware
using the Road Map
Configure Hardware
using Configuration
Assistant
Install NOS
Install Management
Utilities
LHPro
Installation
RoadMap
HPNetServer
!Test your configured hardware using
Diagnostic Assistant (optional)
NOS

This Road Map is for the person who installs, administers, and troubleshoots LAN servers. Hewlett-Packard Company assumes you
are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energylevels.
Audience Assumptions
1Verify Contents
1. Connect the monitor, keyboard and mouse to the HP NetServer and plug in the power
cord for the HP NetServer and the monitor. Attach the power cord to the powercord
retainer on the back of the HP NetServer.
If you are installing a monochrome monitor, you must change a jumper setting on the
system board. See the for information.
2. If you have a UPS, install and turn on the UPS. Use the supplied serial cable to connect
the UPS to the HP NetServer. Refer to the user’s guide included with the UPS for
additional information.
3 Plug in the power cords for the HP NetServer and monitor and turn them both on.
4. Insert the HP NetServer Navigator CD-ROM into the CD-ROM drive and press the
Reset button on the front of the server. The HP NetServer automatically boots from the
HP NetServer Navigator CD-ROM.
If an error message appears, ignore it and press the F1 key. If an error message
appears in Configuration Assistant, press F10 to continue.
5. Go to the HP NetServer Navigator Main Menu. If the language needs to be changed,
select "Set Preferences."
6. Select "Readme File."
7. If you are installing options, youwill need to remove the cover. Go to Step 3: "Remove
the Cover."
If you are not installing options, go to Step : "Configure the HP NetServer and Install
Additional ISA Boards."
HP NetServer LH User Guide
The Readme file contains the latest information to help you
install your HP NetServer. Read it carefully before beginning your installation.
Pro
8
2View the Readme File Power
cord
retainer
From HP
NetServer
From
Monitor
To serial port of
HP NetServer
3Remove the Cover
If you are installing options, youwill need to remove the cover.
Tools you will need:
Flat 1/4-inch screwdriver T15 TORX® driver
Antistatic service kit (3M® 8501/8502/8505 or equivalent). The kit includes a
static-dissipative work surface, chassis clip lead, and wrist strap
!
!
and
1. Turn off the NetServer and disconnect the power cord.
2. Unlock the cover using the key in the key bag.
3. Loosen the five mounting screws on the back of the HP NetServer.
4. Slide the cover forward 2 inches (5 cm) and then lift it straight up.
WARNING Before removing the cover, always disconnect the power
cord and unplug telephone cables. Disconnect telephone
cables to avoid exposure to shock hazard from telephone
ringing voltages. Disconnect the power cord to avoid
exposure to high energy levels that may cause burns when
parts are short-circuited by metal objects such as tools or
jewelry.
CAUTION Wear a wrist strap and use a static-dissipative work surface
connected to the chassis when handling components. Key
Bag
UPS
Key lock
Unpack and verify the contents of the shipping box against the Contents Checklist included with your NetServer. If anything is
missing or damaged, call your reseller.
!
!
!
!
!
Fax:
Internet WWW:
Internet FTP:
BBS:
CompuServe:
Call HP’s fax systemat 1-800-333-1917(or 1-208-344-4809from your fax machine). Request the Release History
using the Document Number 6005
http://www.hp.com/go/netserver
//ftp.netserver.hp.com;logon:anonymous; password: <your e-mail address> cd; NSNAVCD; get 6005.txt
Call 1-408-553-3500; download6005.txt from NSNAVCD library
GO HPPC; download 6005.txt from the NetServer library
To obtain drivers and utilities for non-HP components of your system, follow the appropriateInternet, BBS, or CompuServe
procedure specified by the component and network operating system manufacturers.
HP NetServer Navigator CD Release History
To ensure that you have the latest versions of the software, obtain the current Release History. This report describes major software
updates to each release of the HP Navigator CD-ROM and instructions for obtaining a current release.
Obtain the Release History in one of these ways:

Install Additional Memory
4Use HP DIMMs listed on the Technical Information
Label on top of the chassis.
1. Remove the processor board.
2. Align the notches on the DIMM with the keys on
the socket.
3. Insert the DIMM until the retaining clips snap
into place.
4. Reinstall the board.
Technical
Information
Label with DIMM
part numbers
Install DIMMS:
• in any order
•in any socket
5Install Additional EISA Boards
and PCI Boards
NOTE Do not install ISA boards until instructed by the
Configuration Assistant program in Step :
Configure the HP NetServer and Install Additional
ISA Boards.
8
1. Read the documentation included with each board. Look
for any special instructions and refer to the Accessory
Board Installation Recommendations.
2. If necessary, remove the board retainer.
3. Remove the slot cover for each slot used.
Boards can be identified by the shape of their connectors:
EISA
ISA PCI
Accessory Board Installation Recommendations
!
!
!
!
!
!
!
!
Install the optimal PCI performance board (either Network Interface Card or
SCSI controller) in PCI 9.
Install the EISA SCSI controller in slot 1 to ease the routing of cables.
:
CD-ROM drive with bootable CD-ROM
Flexible disk drive with bootable flexible disk
IDE drive
EISA or ISA controller set to BIOS address C8000 (To boot from an EISA or
ISA controller, set the BIOS address to C8000. Other controllers must have
BIOS disabled or addresses set at the end of the D0000 range.)
PCI controller (embedded SCSI A, embedded SCSI B, PCI slots in the
following order: 9, 8, 7, 6, and 5. The PCI boot priority order can be changed
so that PCI slots precede SCSI A and SCSI B.
Set BIOS addresses, disable BIOSes and change PCI boot priority order
using the EISA Configuration Utility in Step 8: "Configure the HP NetServer
and Install Additional ISA Boards."
For a complete description of the boot device priority order, see Information
Assistant on the HP NetServer Navigator CD-ROM.
Boot device priority order
CPU
PCI Bus 0
PCI 9
PCI Bus 1
PCI 8
PCI 7
PCI 6
PCI 5
EISA/ISABus
E5
E4
E3
E2
E1
Technical
Information
Label
Board
Retainer
Keys
Notches

6Install Additional Mass Storage Devices
NOTE If you are installing an IDE drive or SCSI devices with certain
configurations, you will need additional cables or adapters.
For configuration information, see the Technical Information
Label on the side of the chassis or Information Assistant on
the HP Navigator CD-ROM.
For part numbers for HP cables, adapters, and trays, see the
technical information labels on the top and side of chassis.
Shelf 3
Hot Swap Subsystem
!
!
!
!
!
!
!
!
A SCSI, IDE or flexible disk drive can be installed in
Shelf 3.
If you are installing anarrow (50-pin) SCSI device, it can
be cabled with the CD-ROM in Shelf 2.
If you are installing a SCSI device, set the jumpers on the
device to an unused address (the CD-ROM drive is set to
SCSI address 5.) Do not terminate device if using
NetServer cable.
All devices must be installed in mass storage trays.
All devices must be installed in mass storage trays.
Unlock the hot swap subsystem using the same key used
to unlock the NetServer cover. The key is located in the
keybag attached to the rear of the HP NetServer.
Cabling configuration diagrams of the hot swap
subsystem are shown on the Technical Information Label
on the side of the chassis and in Information Assistant.
SCSI address setting information is in Information
Assistant and the .
HP NetServer LH User GuidePro
8
7
Configure the HP NetServer and
Install Additional ISA Boards
(Optional) Install Redundant Power Supply
NOTE Do not install ISA boards until instructed
by the Configuration Assistant program.
1. Reassemble the HP NetServer and connect the power cord.
2. Turn on the HP NetServer and monitor.
3. If the HP NetServer Navigator CD-ROM is not loaded in the
CD-ROM drive, insert the CD-ROM into the CD-ROM drive now
and press the Reset button on the front of the server. The HP
NetServer automatically boots from the HP NetServer
Navigator CD-ROM.
If an error message appears, ignore it and press the F1 key. If
an error message appears in Configuration Assistant, press
F10 to continue.
4. Go to the HP NetServer Navigator Main Menu and select
“ConfigurationAssistant."
5. If you have installed all accessories except the
ISA boards, go to the Express Configuration Menu. Follow the
instructions on the screen to configure your HP NetServer.
You are finished with the Installation Road Map. Follow the
instructions in Configuration Assistant to continue your
NetServer installation.
Recommended:
NOTE If you are installing one accessory at a time, go to
the Custom Configuration Menu and select the
Help button. Follow the instructions on the screen
to configure your HP NetServer. Repeat
configuration process for each accessory.
Install the redundant power supply by following the instructions
included with the power supply.
Technical
Information
Label (on top
of chassis)
Shelf 3
(No tray
provided)
Key Lock
Technical
Information
Label with
cabling
configuration
information
CAUTION To ensureproper cooling either two power supplies
or one power supply and one fan must be installed at
all times.