HP 6125G Installation manual

HP 6125 Blade Switch Series
A
bout the HP 6125 Blade Command References
Part number: 5998-3163
Software version: Release 2103
Document version: 6W100-20120907

Legal and notice information
© Copyright 2012 Hewlett-Packard Development Company, L.P.
No part of this documentation may be reproduced or transmitted in any form or by any means without
prior written consent of Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing, performance, or
use of this material.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained
herein.

About the HP 6125 Blade command references
The HP 6125 Blade command references describe the commands and command syntax options
available for the HP 6125 Blade Switch Series.
Command Reference Content
01 Fundamentals Command
Reference
Covers the commands for logging in to and setting up the switch. This
command reference includes:
•CLI (command privilege settings and CLI management commands)
•Logging in to the switch
•FTP
•TFTP client
•File management commands
•Configuration file management
•Software upgrade
•Device management
02 IRF Command Reference Covers IRF configuration commands, including IRF port binding,
member ID assignment, priority assignment, and MAD.
03 Layer 2—LAN Switching
Command Reference
Covers the commands for configuring Layer 2 technologies and
features in a LAN switched network. This command reference
includes:
•Ethernet interface
•Loopback and null interfaces
•Bulk configuring interfaces
•MAC address table
•MAC Information
•Ethernet link aggregation
•Port isolation
•Spanning tree
•BPDU tunneling
•VLAN
•Isolate-user-VLAN
•Voice VLAN
•GVRP
•QinQ
•VLAN mapping
•LLDP
•Service loopback group
•Layer 2 forwarding

Command Reference Content
04 Layer 3—IP Services Command
Reference
Covers the commands for configuring and managing IP addressing
(including static and dynamic IPv4 and IPv6 address assignment),
UDP helper, DNS, network performance optimization, ARP, and
interoperation between IPv4 and IPv6. This command reference
includes:
•ARP
•Gratuitous ARP
•Proxy ARP
•ARP snooping
•IP addressing
•DHCP relay agent
•DHCP client
•DHCP snooping
•BOOTP client
•IPv4 DNS
•IP performance optimization
•UDP Helper
•IPv6 basics
•DHCPv6
•Tunneling
05 Layer 3—IP Routing Command
Reference
Covers the commands for configuring routes for IPv4 and IPv6
networks of different sizes, route filtering, route control, and policy
based routing. This command reference includes:
•IP routing basics
•Static routing
•RIP
•OSPF
•IS-IS
•BGP
•IPv6 static routing
•RIPng
•OSPFv3
•IPv6 IS-IS
•IPv6 BGP
•Routing policy
•Policy-based routing

Command Reference Content
06 IP Multicast Command Reference
Covers the commands for Layer 3 IPv4 multicast protocols (IGMP,
PIM, MSDP, and MBGP), and Layer 3 IPv6 multicast protocols (MLD,
IPv6 PIM, and IPv6 MBGP), Layer 2 IPv4 multicast protocols (IGMP
snooping, PIM snooping, and multicast VLAN), and Layer 2 IPv6
multicast protocols (MLD snooping, IPv6 PIM snooping, and IPv6
multicast VLAN). This command reference includes:
•IGMP snooping
•PIM snooping
•Multicast VLAN
•Multicast routing and forwarding
•IGMP
•PIM
•MSDP
•MBGP
•MLD Snooping
•IPv6 PIM snooping
•IPv6 multicast VLAN
•IPv6 multicast routing and forwarding
•MLD
•IPv6 PIM
•IPv6 MBGP
07 ACL and QoS Command
Reference
Covers the commands for classifying traffic with ACLs, and allocating
network resources and managing congestions with QoS technologies
to improve network performance and network use efficiency. This
command reference includes:
•ACL
•QoS policy
•Priority mapping
•GTS and line rate
•Congestion management
•Congestion avoidance
•Aggregate CAR

Command Reference Content
08 Security Command Reference
Covers security feature commands. Available security features
include identity authentication (AAA), access security (802.1X, MAC
authentication and port security), secure management (SSH), and
attack protection (IP source guard, ARP attack protection, and URPF).
This command reference includes:
•AAA
•802.1X
•EAD fast deployment
•MAC authentication
•Port security
•User profile
•Password control
•Public key
•PKI
•SSH
•SFTP
•SCP
•SSL
•TCP attack protection
•IP source guard
•ARP attack protection
•ND attack defense
•URPF
•MFF
09 High Availability Command
Reference
Covers high availability commands for managing failure detection
and failover. Failure detection technologies focus on fault detection
and isolation. Failover technologies focus on network recovery. This
command reference includes:
•Ethernet OAM
•CFD
•DLDP
•RRPP
•Smart Link
•Monitor Link
•VRRP
•BFD
•Track

Command Reference Content
10 Network Management and
Monitoring Command Reference
Covers the commands that help you manage and monitor your
network, for example, manage system events, sample packets, assess
network performance, synchronize the clock for all devices with the
clock in the network, and test network connectivity. This command
reference includes:
•Ping, tracert, and system debugging
•NTP
•Information center
•SNMP
•RMON
•Port mirroring
•Traffic mirroring
•NQA
•sFlow
•IPC