HP J9661A User manual

HP V1410 Switch Series
Installation and Getting Started Guide
HP V1410-8 Switch (J9661A)
HP V1410-16 Switch (J9662A)
HP V1410-24 Switch (J9663A)
HP V1410-24-2G Switch (J9664A)

HP V1410 Switch Series
Installation and Getting Started Guide

Hewlett-Packard Company
8000 Foothills Boulevard, m/s 5551
Roseville, California 95747-5551
www.hp.com/networking
©Copyright 2011 Hewlett-Packard Development
Company, L.P.
Manual Part Number
5998-0946
April 2011
Applicable Products
Disclaimer
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not
be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing,
performance, or use of this material.
The information contained herein is subject to change
without notice. The only warranties for HP products and
services are set forth in the express warranty statements
accompanying such products and services. Nothing herein
should be construed as constituting an additional warranty.
HP shall not be liable for technical or editorial errors or
omissions contained herein.
Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished
by Hewlett-Packard.
Warranty
For the latest license and warranty information, visit
www.hp.com/networking/support.
A copy of the specific warranty terms applicable to your
Hewlett-Packard products and replacement parts can be
obtained from your HP Sales and Service Office or
authorized dealer.
Safety
Before installing and operating these products, please read
the “Installation Precautions” in chapter 2, “Installing the
Switch”, and the safety statements in the General Safety and
Regulatory Information booklet included with the product.
HP V1410-8 Switch (J9661A)
HP V1410-16 Switch (J9662A)
HP V1410-24 Switch (J9663A)
HP V1410-24-2G Switch (J9664A)

iii
1 Introducing the Switch
Front of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Network Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Back of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
2 Installing the Switch
Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2. Verify the Switch Passes Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
LED Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
3. Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Rack or Cabinet Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Rack Mounting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Wall or Under-Table Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Horizontal Surface Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Using a Kensington Security Cable . . . . . . . . . . . . . . . . . . . . . . . . 2-14
4. Connect the Switch to a Power Source . . . . . . . . . . . . . . . . . . . . . . 2-14
5. Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Using the RJ-45 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Sample Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
As a Desktop Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
As a Segment Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
3 Troubleshooting
Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Contents

iv
Contents
Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
LED patterns for General Switch Troubleshooting . . . . . . . . . . . . . . . 3-3
Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Testing the Switch by Resetting It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Testing Twisted-Pair Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Testing End-to-End Network Communications . . . . . . . . . . . . . . . . . . 3-5
HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
A Specifications
Switch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
BTU Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Cabling and Technology Information Specifications . . . . . . . . . . . . . . . . . A-3
Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Straight-through Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . A-6
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
Crossover Twisted-Pair Cable for
10 Mbps or 100 Mbps Network Connection . . . . . . . . . . . . . . . . . . . . . A-7
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Straight-Through Twisted-Pair Cable for
1000 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
B EMC Regulatory Statements
Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

v
Contents
Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Index

vi
Contents

1-1
1
Introducing the Switch
The HP V1410-8, V1410-16, V1410-24, and V1410-24-2G Switches are multiport
unmanaged switches that can be used to build high-performance switched
workgroup networks. These switches are store-and-forward devices that offer
low latency for high-speed networking.
Throughout this manual, these switches will be referred to as the V1410-8
Switch, V1410-16 Switch, V1410-24 Switch, and the V1410-24-2G Switch.
■The V1410-8 Switch has 8 auto-sensing 10/100Base-TX RJ-45 ports.
■The V1410-16 Switch has 16 auto-sensing 10/100Base-TX RJ-45 ports.
■The V1410-24 Switch has 24 auto-sensing 10/100Base-TX RJ-45 ports.
HP V1410-8 Switch (J9661A)
HP V1410-16 Switch (J9662A)
HP V1410-24 Switch (J9663A)
HP V1410-24-2G Switch (J9664A)

1-2
Introducing the Switch
■The V1410-24-2G Switch has 24 auto-sensing 10/100Base-TX RJ-45 ports
and two 10/100/1000Base-T RJ-45 ports (ports 25 and 26).
These switches can be directly connected to computers, printers, and servers
to provide dedicated bandwidth to those devices, and you can build a switched
network infrastructure by connecting the switch to hubs, other switches, or
routers.

1-3
Introducing the Switch
Front of the Switch
Front of the Switch
HP V1410-8 Switch (J9661A)
Power LED
Link/Activity LEDs
Speed LEDs
HP V1410-16 Switch (J9662A)
Power LED
Link/Activity LEDs
10/100Base-TX RJ-45 ports1Speed LEDs
HP V1410-24 Switch (J9663A)
Power LED
Link/Activity LEDs
10/100Base-TX RJ-45 ports1
Speed LEDs
1 All RJ-45 ports have the Auto-MDIX feature.
HP V1410-24-2G Switch (J9664A)
Power LED
Link/Activity LEDs
10/100Base-TX RJ-45 ports1
Speed LEDs 10/100/1000Base-T RJ-45 ports1

1-4
Introducing the Switch
Front of the Switch
Network Ports
■8, 16, or 24 auto-sensing 10/100Base-TX ports.
All these ports have the “Auto-MDIX” feature, which means that you can
use either straight-through or crossover twisted-pair cables to connect
any network devices to the switch.
■(V1410-24-2G Switch only) 2 auto-sensing 10/100/1000Base-T ports.
These ports have the “Auto-MDIX” feature, which means that you can use
either straight-through or crossover twisted-pair cables to connect any
network devices to the switch.
LEDs
The front panels of the switches provide status LEDs for system monitoring.
Table 1-1 details the functions of the LED indicators.
Table 1-1. Switch Status LEDs
Switch LEDs State Meaning
Power
(green)
On The switch is properly receiving power.
Off No power connection. The switch is NOT receiving power.
Port LEDs
Link/Act
(green)
On The port is enabled and receiving a link indication from the connected device.
Off One of these condition exists:
• no active network cable is connected to the port
• the port is not receiving link beat or sufficient light
Flashing1Indicates that there is network activity on the port.
Spd
(green)
On Indicates the port is operating at 100 Mbps (100 Mbps or 1000 Mbps for ports 25 and
26 on the V1410-24-2G Switch).
Off Indicates the port is operating at 10 Mbps.
1The flashing behavior is an on/off cycle once every 0.083 seconds approximately.

1-5
Introducing the Switch
Back of the Switch
Back of the Switch
Power Connector
The switches do not have a power switch. They are powered on when the
external AC/DC power adapter is connected to the switch and to a power
source. The external AC/DC power adapter supplies 12 volts DC to the switch
and automatically adjusts to any AC voltage between 100-240 volts and either
50 or 60 Hz. No voltage range settings are required.
DC power connector
HP V1410-8 Switch (J9661A)
HP V1410-16 Switch (J9662A)
HP V1410-24 Switch (J9663A)
Power cord retention ring
DC power connector Power cord retention ring
10/100Base-TX RJ-45 ports
DC power connector
HP V1410-24-2G Switch (J9664A)
DC power connector
Power cord retention ring
Power cord retention ring

1-6
Introducing the Switch
Switch Features
Switch Features
The features of the switches include:
■8, 16, or 24 auto-sensing 10/100Base-TX RJ-45 ports with Auto-MDIX.
■The V1410-24-2G Switch includes 24 auto-sensing 10/100Base-TX RJ-45
ports and two auto-sensing 10/100/1000Base-T RJ-45 ports, all with
Auto-MDIX.
■Plug-and-play networking—all ports are enabled—just connect the
network cables to active network devices and your switched network is
operational.
■Auto-MDIX on all twisted-pair ports, meaning that all twisted-pair
connections can be made using straight-through cables. Cross-over cables
are not required, although they will also work.
■Automatically negotiated full-duplex operation for the RJ-45 ports when
connected to other auto-negotiating devices.
■The 16- and 24-port models support new IEEE 802.3az features in the
100 Mbps mode. This new Energy Efficient Ethernet (EEE) standard
reduces power consumption when connected with EEE-compliant client
devices.
■Automatic learning of the hardware addresses in each switch’s 8000-
address forwarding table (1040-addresses for the V1410-8 Switch).
■The V1410-16 Switch and V1410-24 Switch include support for up to 2048-
byte Jumbo frame size to improve performance of large data transfers.
■Support for IEEE 802.1p prioritization Quality of Service (QoS) to deliver
data to devices based on the priority and type of traffic.
■Fanless designed enables quiet operation for deployment in open spaces.

2-1
2
Installing the Switch
This chapter provides installation information for the V1410-8 Switch,
V1410-16 Switch, V1410-24 Switch, and V1410-24-2G Switch.
Included Parts
The switches have the following components:
■Documentation kit
■Four rubber feet
■Wall/table-mount accessory kit:
■Rack-mount accessory kit:
• Read Me First
• Switch Quick Setup Guide
• Safety and Regulatory information
• Software End User License and Hardware Warranty information
Kit number 5066-0621
Contains:
• three 3/4” (20-mm M4) screws for
wall and under-table mounting
• three wall anchors
• cable tie for power cord
V1410-16 Switch V1410-24 Switch
V1410-24-2G Switch
Kit number 5066-0622
Contains:
• two mounting brackets
• eight 8-mm M4 screws to attach the
mounting brackets to the switch
• four 5/8-inch number 12-24 screws to
attach the switch to a rack
Kit number 5066-0623
Contains:
• two mounting brackets
• eight 8-mm M4 screws to attach the
mounting brackets to the switch
• four 5/8-inch number 12-24 screws to
attach the switch to a rack

2-2
Installing the Switch
Included Parts
■External AC/DC power adapters and power cords, one of the following:
Japan Power
Cord Warning
•Universal External AC/DC Power Adapter
All countries/regions 5066-1122
Power cord options for Universal AC/DC Adapter
Australia/New Zealand
China
Continental Europe/Denmark/
....Switzerland/Israel/Vietnam/Indonesia
India
Japan
South Africa
Taiwan
Thailand
United Kingdom/Hong Kong/
....Singapore/Malaysia
United States/Canada/Mexico
Brazil
Argentina
Chile
8121-0870
8120-8373
8120-6314
8121-0702
8120-6316
8120-6317
8121-0963
8121-0664
8120-8699
8120-6313
8121-1081
8120-8367
8121-0514
• Wall Plug-in External AC/DC Power Adapter
(AC Power cords are not used)
United States/Canada
Continental Europe/Denmark/
....Norway/Sweden/Switzerland
5184-5863
5184-5864

2-3
Installing the Switch
Included Parts
Installation Precautions
WARNING ■The rack or cabinet should be adequately secured to prevent it
from becoming unstable and/or falling over.
Devices installed in a rack or cabinet should be mounted as low as
possible, with the heaviest devices at the bottom and progressively
lighter devices installed above.
■Wall-mount the switches with network ports facing up (away from
the floor) or down (toward the floor). Do not wall-mount any of
the switches with the ventilation ducts facing up or down.
Cautions ■Use only the AC/DC power adapter supplied with the switch for
connection to an AC power source.
■If your installation requires a different power cord than the one supplied
with the switch, ensure the cord is adequately sized for the switch’s
current requirements. In addition, be sure to use a power cord displaying
the mark of the safety agency that defines the regulations for power cords
in your country. The mark is your assurance that the power cord can be
used safely with the switch. If the supplied power cord does not fit,
contact HP networking support.
■When installing the switch, the AC outlet should be near the switch and
should be easily accessible in case the switch must be powered off.
■Ensure the switch does not overload the power circuits, wiring, and over-
current protection. To determine the possibility of overloading the supply
circuits, add together the ampere ratings of all devices installed on the
same circuit as the switch and compare the total with the rating limit for
the circuit. Maximum ampere ratings are usually printed on the devices
near the AC power connectors.
■Do not install the switch in an environment where the operating ambient
temperature might exceed 40°C (104°F). This includes a fully-enclosed
rack. Ensure the air flow around the sides and back of the switch is not
restricted. Leave at least 7.6 cm (3 inches) for cooling.
■Ensure all port covers are installed when the port is not in use.

2-4
Installing the Switch
Installation Procedures
Installation Procedures
These steps summarize your switch installation. The rest of this chapter
provides details on these steps.
1. Prepare the installation site (page 2-5). Make sure the physical
environment into which you will be installing the switch is properly
prepared, including having the correct network cabling ready to connect
to the switch and having an appropriate location for the switch. See page
2-3 for some installation precautions.
2. Verify the switch passes self test (page 2-6). Plug the switch into a
power source and observe that the LEDs on the switch’s front panel
indicate correct switch operation.
3. Mount the switch (page 2-8). The V1410-16, V1410-24, and V1410-24-2G
Switches can be mounted in a 19-inch telco rack, in an equipment cabinet,
on a wall, under a table, or on a horizontal surface. The switches can also
be mounted on a wall, under a table, or on a horizontal surface.
4. Connect power to the switch (page 2-14). Once the switch is mounted,
plug it into the main power source.
5. Connect the network devices (page 2-16). Using the appropriate
network cables, connect the network devices to the switch ports.
At this point, your switch is fully installed. See the rest of this chapter if you
need more detailed information on any of these installation steps.

2-5
Installing the Switch
Installation Procedures
1. Prepare the Installation Site
■Cabling Infrastructure - Ensure the cabling infrastructure meets the
necessary network specifications. See appendix A, “Cabling and
Technology Information Specifications” for more information:
■Installation Location - Before installing the switch, plan its location and
orientation relative to other devices and equipment:
• In the front or back of the switch, depending on where the ports are
located, leave at least 7.6 cm (3 inches) of space for the twisted-pair
cabling.
• In the back of the switch, leave at least 3.8 cm (1 1/2 inches) of space
for the power cord.
• On the sides of the switch, leave at least 7.6 cm (3 inches) for cooling.

2-6
Installing the Switch
Installation Procedures
2. Verify the Switch Passes Self Test
Before mounting the switch in its network location, you should first verify it
is working properly by plugging it into a power source and verifying it passes
its self test.
1. Connect the AC/DC adapter’s power cord to the power connector on the
back of the switch, and then plug the AC/DC power adapter into a nearby
properly grounded electrical outlet.
Note The switches are shipped with one of two types of AC/DC power adapter;
either the universal AC/DC adapter with an AC power cord, or the wall plug-
in AC/DC adapter (without an AC power cord).
Figure 2-1. Connecting the switch power adapter
Connect the wall plug-in AC/DC
power adapter to the switch and
an AC power outlet
Connect the universal AC/DC
power adapter to the switch
and an AC power outlet
V1410-8 Switch
V1410-16 Switch