Huawei HG8010 series User manual

International Communication Instrument Co., Ltd. (ICI)
Network Expertise Helps You Succeed
Dear Sir. / Madam,
How are you doing? Thanks for downloading this document.
Our company, ICI is an international telecommunication and ICT system consultant and value add distributor. We operate
in Beijing, China. Our main business is selling fixed telecom network equipments to world-wide customers, e.g. telecom
service providers and system integrators. We are specialized in below product series,
A. Optic transmission network equipments
a) Huawei Metro 1000, OSN 1500, OSN 3500, and OSN 7500 SDH/MSTP equipments.
b) Cisco 15454 / 15454E series SDH/MSTP equipments.
c) Potevio and other major Chinese brands’microwave transmission equipments.
B. Data / IP network equipments
a) Cisco routers
i. Cisco 1941/2901/2911/2921/2951/3925/3945 series ISR G2 access routers.
ii. Cisco ASR1000 / ASR9000 / CRS-1 series service provider core and edge routers.
b) Cisco and Huawei Ethernet switches
i. Cisco 2960/2960S/3560/3560E/3560X/3750/3750E/3750X series access switches
ii. Cisco 4900/4500/6500 & Cisco Nexus 7000/5000/2000/1000 core and data center switches
iii. Huawei 2300/3300/5300/2700/3700/5700 series access switches.
iv. Huawei 9300/6700/7700 series high-end switches.
C. Access network equipments
a) Huawei UA5000 and other integrated access equipments..
b) Huawei MA5680T/MA5683T series OLT and FTTx equipments.
c) Huawei MA5600 series MDU: MA5616 (ADSL2+&POTS), MA5620 (FE&POTS), MA5626 (POTS).
D. Other telecom project and system materials, e. g. fiber optic cables, CAT5E cables, and other bulk materials.
Our contact information and monthly-updated product catalog is as below,
Contact:
Morris Hagen
Mobile: [phone]
Office Phone: [phone]
Email: [e-mail]
MSN Messenger: [e-mail]
Yahoo Messenger: [e-mail]
Skype: morris.hagen.ici
Website: http://www.ici-cn.com
Monthly-updated Product Catalog: http://www.ici-cn.com/download/pricing/ICI_Catalog.xls
We sincerely wish that we could bring solid help to your business!
Best Regards,
Morris Hagen, Sales Team of ICI
Network Expertise Helps You Succeed

Quick Start
EchoLife Bridge GPON Terminal

1
Safety Precautions
To use the device properly and safely, read the safety precautions carefully
before using the device and strictly observe these precautions when using
the device.
Do not look directly into the optical port without eye protection.
Keep the device out of the reach of children as the components or accessories
may be swallowed.
Install the device in strict compliance with the requirements of the supplier.
Reserve a space of at least 10 cm above and around the device for heat
dissipation. During the installation, keep the device away from electric appliances
that generate strong magnetic or electric fields, such as microwave ovens,
refrigerators, and mobile phones.
The power supply voltage of the device must meet the requirements on the input
voltage of the device.
Do not use any power adapters that are not in the standard configuration.
Otherwise, the device may be abnormal or unsafe.
Dry your hands before connecting or disconnecting cables. Stop the device and
switch off the power before connecting or disconnecting cables.
Do not place any object on the device, so that the device will not be damaged
due to overheating or deformation.
Prevent objects, such as metal, from entering the device through the heat
dissipation hole.
Switch off the power and disconnect all cables, including the power cable, optical
fiber, and network cable, during periods of lightning activities.
Do not lead the strength member of the optical fiber or other metal parts indoors.
Do not install telephone lines, network cables, power adapters or power adapter
cables outdoors. Adopting these measures will help prevent device damage and
bodily injuries which are especially prone during thunderstorms.
If an abnormality occurs, for example, liquid entering the device, smoke, unusual
sound, and smell, stop the device immediately, switch off the power, disconnect
all cables (such as the power cable, optical cable, and network cable) to the
device, and contact the authorized service center.
Do not disassemble the device without permission. In the case of a device fault,
contact the authorized service center.
Dispose of the packing materials, expired batteries, and old or abandoned
devices in accordance to local laws and regulations (recycling them is strongly
recommended).
Do not change the structure, safety design, or performance design of the device
without prior authorization.

2
Product Overview
Product Function
HG8010 series 1 Ethernet port
HG8110 series
1 Ethernet port
1 POTS port
HG8240 series
4 Ethernet ports
2 POTS ports
HG8242 series
4 Ethernet ports
2 POTS ports
1 CATV port
HG8040 series 4 Ethernet port
This document is updated to September 2011. If some device types are not in the preceding list, refer
to http://www.huawei.com.
NOTE
Technical Specifications
Power adapter input: 100–240 V AC, 50–60 Hz
System power supply: See the nameplate on the device.
Ambient temperature: 0ºC to +40ºC
Ambient humidity: 5%–95% (non-condensing)
For other technical specifications, see the following table.

3
GPON Terminal Weight
(Including the Power Adapter)
Maximum System
Power Consumption
HG8010 series About 450 g ≤6 W
HG8110 series About 450 g ≤7 W
HG8240 series About 500 g ≤12 W
HG8242 series About 750 g ≤14 W
Installing the GPON Terminal
1. Do not install GPON terminals outdoors or on the outdoor cabinets.
2. GPON terminals can be mounted onto a wall or be placed on a workbench. Do not install GPON
terminals in other modes, such as the ceiling.
3.The terminal cannot be connected to other devices such as GPON terminals, switch and router.
Caution
If the appearance of the product in this document differs from the actual product, the actual product
prevails.
NOTE
The procedure and schematic diagram for placing the device on a desk
vertically (only some products support this mode) are as follows:
Step 1 Install a base on the installation hole of the GPON terminal.
Step 2 Place the GPON terminal with the base, for example, an HG8110 on the
workbench vertically.
The schematic diagram for placing the device on a desk horizontally are as
follows:

4
Mounting a GPON terminal onto the wall
Step 1 Mark the positions of two holes (with a spacing listed in the following table) used
for mounting a GPON terminal.
Step 2 Select a proper drill according to the outer diameter of the screws. Use a
hammer drill to drill the marked positions on the wall. Then clean the wall and
install two expansion bolts.
Step 3 Use a screwdriver to fasten the screws into the expansion bolts, leaving the heads
of the screws 3 mm over the wall. Then install the GPON terminal to the screws.

This document uses the HG8242 as an example to describe the connections. Ports on
GPON terminals of other types may be different. Therefore, connect cables based on
the ports that are actually supported by the device. If the external device is different
from the device in the figure, refer to the description for connections of the external
device.
5
1CATV port
2Optical port
3Ethernet port
4POTS port
5Power switch
6Power port
Connecting Cables
7Backup battery
monitoring port
8Reset

Step 1 Use an optical fiber to connect the OPTICAL port on the GPON terminal to the
optical port in the wall.
Step 2 Use a coaxial cable to connect the CATV port to a TV set or set top box (STB).
Step 3 Use a network cable to connect the LAN port to a PC or the Ethernet port on
the IP STB.
Step 4 Use a phone line to connect the TEL port to a phone or fax machine.
Step 5 Use a power adapter to connect the POWER port to the power socket.
Step 6 Press the ON/OFF power switch.
6
NOTE
NOTE
1.The optical connector connected to the OPTICAL port is an SC/APC connector, and the
type of the optical connector connected to the optical port in the wall is determined by practical
conditions.
2.To ensure normal use of fibers, make sure that the fiber bend radius is larger than
30 mm.
The preceding figure connects the power adapter as an example. For details about how to
use the backup battery unit, see the usage guide to the backup battery.
Step 1 Set the IP address of the PC in the same subnet as the management IP address
of the GPON terminal. For example,
-IP address: 192.168.100.100
-Subnet mask: 255.255.255.0
Step 2 Enter the management IP address of the GPON terminal in the address bar of
Internet Explorer and press Enter.
The login window is displayed.
Step 3 In the login window, select your preferred language, enter the user name and
password (default user name is root and default password is admin), and
click Login. After the password is authenticated, the Web configuration window
is displayed.
Logging in to the Web Configuration Window
NOTE
The default management IP address and subnet mask of the GPON terminal are as follows:
-IP address: 192.168.100.1
-Subnet mask: 255.255.255.0

Indicator Description
Indicator Status Description
CATV
Steady on The CATV function is enabled and CATV signals
are received.
Off The CATV function is disabled or CATV signals
are not received.
TEL1–TEL2
Steady on The connection between the TEL port and the
voice server is set up.
Blinks twice a
second
The connection between the TEL port and the
voice server is set up and the phone is in the off-
hook or ringing state.
Blinks once two
seconds The TEL port is registering with the voice server.
Off The connection between the TEL port and the
voice server is not set up.
LAN1–LAN4
Steady on The Ethernet connection is in the normal state.
Blinking Data is being transmitted on the Ethernet port.
Off The Ethernet connection is not set up.
LOS/PON See Table 2.
POWER
Steady green The terminal is powered on.
Steady yellow The backup battery is supplying power.
Off The power supply is cut off.
Table 1 Indicator status description 1
7
Status
No.
Status Description
PON LOS
1 Off Off The GPON terminal is disabled by the
upper-layer device.
2Blinks twice
a second Off The GPON terminal attempts to set up a connection with its upper-layer device.
3 Steady on Off A connection is set up between the GPON
terminal and its upper-layer device.
4 Off Blinks once
two seconds
The Rx optical power of the GPON terminal
is lower than the optical receiver sensitivity.
5Blinks twice
a second
Blinks twice a
second
The GPON terminal is a rogue terminal,
contact the service provider for help.
Table 2 Indicator status description 2

8
The LOS indicator blinks.
If the LOS indicator blinks once two seconds, check whether the pigtail fiber
is properly connected and the connector is clean.
If the GPON terminal blinks twice a second, contact the service provider for help.
The PON indicator is off.
Check whether the OPTICAL port and optical fiber is properly connected.
The GPON terminal fails to register with the upper-layer device. Contact the
service provider for help.
The phone does not ring upon an incoming call but communication is in
normal state when the phone is in off-hook state.
The GPON terminal provides a maximum of 60 V AC ringing current
voltage.Check whether the ringing current voltage of the phone is higher than
60 V AC. If it is higher than 60 V AC, replace it with another phone.
How to reset the GPON terminal?
Press RESET by using a needle-type object.
How can I restore factory defaults?
Press RESET by using a needle-type object for longer than 10s to restore
factory defaults and reset the GPON terminal. If the indicator is off and then
is lit, the system restarts successfully.
FAQs