Huawei OptiX PTN Series User manual

HUAWEI TECHNOLOGIES CO., LTD.
OptiX PTN 960 Packet Transport Platform of PTN Series
Quick Installation Guide
Issue: 08
Date: 2016-01-15

Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://www.huawei.com
Email:
[email protected]

Precautions
Page 1
Tools for Installation
Introduction to the Chassis
Installing and Routing
Cables
Checking the Insatllation
Powering On the
Equipment
End
Start
Check Fiber Connection
Powering on the
Equipment
Preparation for
Installation
Installing the Chassis
Checking Cable
Connectivity
Common Cables for the
Chassis
Installing the Protection
Grounding Cable
(Mandatory)
Installing Power Cable
(Mandatory)
Installing the E1 Cable
Installing the Ethernet
Service Cable
Installing Fibers
Installing the NM
Cable
Page 2
Page 3
Pages
4-7
Pages
8-12
Page 14
Page 13
Page 15
Pages
16-17
Page 8
Pages
9-10
Page 10
Page 8
Page 16
Page 17
Expected Effect of
Installation in a 19-Inch
Cabinet
Installing the External
Clock/Time Cable
Page 11
Page 11
Page 12
Page 12
Installing the Chassis in a
19-Inch Cabinet
Page 4
Page 5 Installing the Chassis in an
ETSI Cabinet
Installing the Chassis in
an open rack
Page 6
Installing the Chassis
into the indoor mini box
mounted on the wall
Page 7
Installation Flow
Certain operations are optional. Before performing an optional operation, consult with the engineering
supervisor or software debugging engineer to decide whether to perform the operation. The other
operations are mandatory.
After you finish the installation, send the information about the bar code to Huawei Headquarters
according to the Tabulation for the Feedback of Bar Codes of Equipment at Stations.

Precautions
1
NOTE
Bundling cables
CAUTION
CAUTION
CAUTION
This document provides simple and distinctive guidelines for quick hardware installation of the PTN 950.
This document does not describe pre-delivery assembly. This document only describes procedures for onsite
installation.
Electrostatic Discharge
Always wear an anti-static ESD wrist strap when handling the equipment or sensitive components to prevent
electrostatic discharge causing possible bodily injury or damage to the equipment or sensitive components. Ensure
that the other end of the ESD wrist strap is properly grounded.
Binding intervals between cable ties or optical fiber binding straps inside the cabinet cannot exceed 250 mm.
(Binding intervals cannot exceed 200 mm for user cables).
Binding intervals between cable ties for all cables and corrugated pipes outside the cabinet are determined based on
the distance between the two horizontal beams. If the cable trough does not contain any beams, the binding intervals
between cable ties cannot exceed 250 mm.
Verify that the equipment room, power supply, ground cables and optical cables are ready for installation. Start the
installation according to the engineering design documents after confirming that conditions are met. Refer to the
Installation Guide for information about specific operational requirements and technical specifications.
Pre-Installation Check
CAUTION
The PTN 960 supports indoor and outdoor installation. Ensure that the requirements on device operating
environments are met before installation. Using the outdoor cabinets IMB network box, APM30H, and R01S200 can
moderately improve the device operating environments. You can use the ETP4830 external AC power system to
supply power to the network boxes and outdoor cabinets. If you need to use an outdoor cabinet other than the IMB
network box, APM30H, and R01S200 for the PTN 960, contact Huawei to determine whether the outdoor cabinet
meets requirements of Huawei devices on the device operating environments.

2
Tape measure Philips screwdriver
(M2-M6) Flathead screwdriver
(M2-M6) Adjustable wrench
Level bar
Ratchet crimp tool Cable cutter
Wire stripper Network cable crimping
pliers Diagonal pliers
Crimping tool Sharp-nose pliers
Bayonet wrench
Paper knife
Marker pen
Electric iron
Heat gun
Multimeter
Antistatic gloves
Binding strap Insulation tape
Antistatic wrist strap
Punching wire pliers
Cleaner
Tools for Installation
Coax stripper Cable tester
Optical power meter BER tester

3
1Introduction to Interfaces
Introduction to the Chassis
Installation holes for N63E/19-inch
cabinet and open rack
Installation holes for T63 cabinet
2Introduction to Installation Holes on Both Sides of the Chassis
10
Alarm interface PGND point (19-inch
cabinet)
Power interface
Ethernet service interface
Clock and time interface
10GE Optical interface
Antistatic jack interface
FE\GE Optical interface
NM interface
E1 interface
•The interface shown in the figure is for reference only. The front view is subject to the real PTN 960 equipment.
•The U-shaped slots help you tighten the chassis conveniently.
OptiX
PTN960
10
The PTN 960 is available in two models: common chassis and extended chassis, which are 2 U and 3 U
high, respectively. Installation modes of the two types of chassis are basically the same; therefore, the
common chassis is used as an example to describe the installation of the PTN 960 in this document. For
information about the installation of the extended chassis, refer to the Appendix.

4
Installing the chassis
1Scenario I: Installing the Chassis in a 19-Inch Cabinet
Installing the chassis in the cabinet
bInstalling the PGND cable c
Introduction to the cable guiding frame Fixing the floating nuts
a
2.0±0.2 N·M
M6
Part 1(for a 19-inch cabinet, an
ETSI cabinet, a T63 cabinet or
an open rack)
Mark the position that captive nuts are to be installed to
ensure that captive nuts are correctly installed, and
install four captive nuts on both sides of the rack.
Part 1 cable
guiding frame
2. Place the chassis's
mounting ears and
cabling rack U-shaped
slots over the screws,
tighten the screws at the
bottom.
1.Hang the screws of
the mounting ears on
the chassis to the rack
loosely.
3. use screws to tighten
the top of the chassis. 1.4±0.14 N·M
M4
3.0±0.3 N·M
M5
2. use the removed screw to tighten the
PGND cable.
1.Remove one screw for installing PGND cable before
installing the chassis in the cabinet.
The U-shaped slots help
you tighten the cabling rack
using screws.

5
Bridging
mounting ears
2Scenario II: Installing the Chassis in an ETSI Cabinet
Fixing the floating nuts
aInstalling the mounting ears b
Installing the PGND cable
cInstalling the chassis in the cabinet d
To the grounding point on the
rear rack column of the cabinet
Part 1 cable
guiding frame
M6 screw assembly with flat
washers
Before installing the chassis in an ETSI cabinet, adjust
the mounting holes according to the cabinet type.
3.0±0.3 N·M
M6
2.0±0.2 N·M
M6
1.4±0.14 N·M
M4
Mark the position that captive nuts are to be installed to
ensure that captive nuts are correctly installed, and
install four captive nuts on both sides of the rack.

6
3Scenario III: Installing the Chassis in an Open Rack
Fixing the floating nuts
a
Installing the chassis in the open rack
bInstalling the PGND cable c
2.0±0.2 N·M
M6
2.0±0.2 N·M
M6
To the ground points in the indoor ground bar
If the rack is with round holes,
captive screws can be
fastened without requiring any
captive nuts.
2. Place the chassis's
mounting ears and
cabling rack U-shaped
slots over the screws,
tighten the screws at the
bottom.
1.Hang the screws of
the mounting ears on
the chassis to the rack
loosely.
3. use screws to tighten
the top of the chassis.

PTN 960 Horizontally installed
7
4Scenario IV: Installing the Chassis into the indoor mini box
mounted on the wall
Installing the indoor mini box (IMB) on the wall
a
(a) Right-side-
mounted on the wall (b) Left-side-
mounted on the wall
(
c) Back-mounted on
the
wall
•1. PTN 960 can be installed in the IMB mounted on the wall.
•2. For details about the installation in scenario IV, see "Equipment Installation Guidelines (IMB
Network Cabinet)" in the Installation Guide.
Installing the chassis in the network cabinet of the customer
b
OptiX
PTN960
PTN 960 vertically installed
Ventilation
OptiX
PTN960
Ventilation
The modes of installing the PTN 960 in the network cabinet of the customer vary with the specifications for
the network cabinet of the customer. The following section describes two common modes to serve as a
guide for installation.