Huawei Quidway S1700-24-AC User manual

技术支持
Tool List
工具参考
M6螺钉
M6 screw
Percussion drill(φ8 Drill bit)M6 Plug boltMarker penCrosshead screwdriver Flathead screwdriver
十字螺丝刀 一字螺丝刀 冲击钻（φ8钻头）M6膨胀螺栓记号笔
斜口钳
Diagonal pliers
Cable tie
线扣
防静电手套
ESD-preventive
活动扳手
Adjustable spanner
羊角锤
Claw hammer
浮动螺母
Captive nut
M4螺钉
M4 screw
长挂耳
Long rack-mounting ear
Service and Support
Rev: 02
快速安装指南以及简易使用说明书
Quidway S1700-24-AC以太网交换机
Quidway S1700-24-AC Ethernet Switch
User Manual & Installation Quick Start
胶垫贴
Rubber pads
Accessories (S1700-24-AC)
设备附件介绍(S1700-24-AC)
Fix the rack-mounting ears.
安装挂耳。
IEC cabinet (19 inch)
IEC 机柜(19英寸)
Install the device in a cabinet.
安装设备到机柜。
Fix the captive nuts.
安装浮动螺母。
1U
1U=44.45mm
Before installation, take ESD-preventive measures, for example, wear ESD-preventive gloves or a wrist strap.
安装前请做好防静电保护措施，如配戴防静电手套或防静电手腕。
Installing the Device in a 19'' Cabinet
安装设备到19英寸标准机柜中
Precautions
注意事项
Use installation strip tofix the captive nuts.
使用安装条安装浮动螺母。
4

Install the device on the wall.
安装设备到墙面。
Mark the hole locations on the wall according to
the device installed with rack-mounting ears.
根据已安装挂耳的设备，用记号笔标记打孔位置。
φ8 Drill bit
φ8钻头
M6 plug bolt
M6膨胀螺栓
90。
Install the plug bolt.
安装膨胀螺栓。
Fix the rack-mounting ears.
安装挂耳。
Installing the Device on a Worktable
安装设备到工作台
Powering on the System
上电检查
安装设备到墙面
Installing the Device on a Wall
Rubber pads
胶垫贴
Adhibit the rubber pads.
粘贴胶垫贴。
Install the device on a worktable.
安装设备到工作台。
●To prevent injuries, check that there is no electrical wire at the locations to be drilled before drilling holes in the wall.
●
●
●
Flammable and explosive items under the device is prohibited. Leave more than 100 mm of space around the device for proper heat dissipation.
在墙上打孔时，必须确认打孔处没有墙电，避免造成人身伤害。
设备下方禁止摆放易燃易爆物品，距离设备100mm范围内不能有异物挡住。
5

● Do not connect power cables when the device is powered on, so as to avoid injuries.
● Make sure that the protection grounding cable of the device is grounded.
● The S1700-24-AC can use only AC power supply.
● 严禁在设备安装和布线完成前向设备供电。
● 确定设备保护地线接地。
● S1700-24-AC只支持交流电源。
● Lay out and bundle power cables, optical fibers, and Ethernet cables separately, with the distances in between longer than 10 cm.
● 电源线与信号线缆的间距要大于10厘米。
During the cabling, if the quantity of cables is rather great, you can route the cables in the cabinet first, and then install connectors
to the cables.
布线时，如果线缆数目比较多，为了布线更方便，可以先不做线缆接头，先将线缆在机柜中布置好，再做与设备连接的线缆接头。
Connect the AC power cable.
连接交流电源线。
Connect the PGND cable.
连接地线。
Connecting PGND Cables and Power Cables
连接保护地线和电源线
Laying out Cables
布放线缆
6

● Power on the device only when the input voltage is in the normal range. Test the AC input voltage for S1700-24-AC.
The voltage should range from 100 VAC to 240 VAC.
● After the device is powered on, the PWR LED is on. the port LED status is as shown in below.
● 测试S1700-24-AC的输入电压，若此电压在100-240V交流电正常范围内可将设备上电 。
●
设备上电后，PWR电源指示灯亮，端口LED灯状态如下图所示。
LED Indicator
LED状态
LED Condition
状态
Description
描述
PWR On Green
绿色常亮
On Green
绿色常亮
Internal power is operating normally.
设备正常上电。
Off
熄灭
Power off.
设备未上电。
1-24Port
Blinking Green
绿色闪烁
The port has a valid 10/100Mbps link.
端口建立了10/100Mb连接。
Blinking indicates activity.
闪烁表示正在传输数据。
Off
熄灭
No link.
无效连接。
*此为A级产品，在生活环境中，该产品可能会造成无线电干扰，在这种情况下，可能需要用户对其干扰采取切实可行的防护措施。
This is a Class A product. This product may cause radio interference, in which case the user may be required to take practical precautions interference.
Ethernet cables
以太网线
Cable tie
线扣
Powering on the System
上电检查
1-24 Port LED
1-24 端口指示灯
PWR LED
电源指示灯
7