Huawei FusionModule5000 User manual

FusionModule5000 Smart Modular Data Center
V100R001
Installation Guide (Single-Row
Aisle Containment with 2000
mm High Cabinets, ECC800)
Issue
01
Date
2019-03-05
HUAWEI TECHNOLOGIES CO., LTD.

Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://e.huawei.com

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
About This Document
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes how to install the smart modular data center (smart module for
short) in the single-row aisle containment scenario.
Intended Audience
This document is intended for:
Hardware installation engineers
Commissioning engineers
Maintenance engineers
Technical support engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to
personal injury.
Calls attention to important information, best practices
and tips.
NOTE is used to address information not related to
personal injury, equipment damage, and environment

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
About This Document
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Description
deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all
updates made in previous issues.
Issue 01 (2019-03-05)
This issue is the first official release.

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
Contents
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document ............................................................................................................ ii
1 Installation Preparations.......................................................................................................1
1.1 Transportation and Placing Precautions ..............................................................................................................................1
1.2 Unpacking and Acceptance..................................................................................................................................................2
1.3 Installation Environment Requirements..............................................................................................................................3
1.4 Site Requirements (Power Supply and Distribution Cabinet) ...........................................................................................5
1.5 Site Requirements (New Main Way)...................................................................................................................................6
1.6 Documents.............................................................................................................................................................................8
1.7 Tools and Instruments...........................................................................................................................................................9
1.8 Tools Delivered with Equipment.......................................................................................................................................13
1.9 Personnel Requirements.....................................................................................................................................................15
1.10 Installation Process...........................................................................................................................................................15
2 Scenario Description (Power Supply and Distribution Cabinet) ................................... 17
3 Scenario Description (New Main Way)............................................................................. 19
4 Hardware Installation Preparations................................................................................... 21
4.1 (Optional) Installing Bases.................................................................................................................................................21
4.1.1 Installing Adjustable Bases .............................................................................................................................................21
4.1.1.1 Base Specifications.......................................................................................................................................................21
4.1.1.2 Precautions for Installing the Base..............................................................................................................................21
4.1.1.3 (Optional) Installing the Support for a Cabinet..........................................................................................................22
4.1.1.3.1 Assembling a Base.....................................................................................................................................................22
4.1.1.3.2 Positioning Bases.......................................................................................................................................................24
4.1.1.3.3 Securing Bases...........................................................................................................................................................26
4.1.2 Installing Fixed-Size Bases.............................................................................................................................................28
4.1.2.1 Deploying a 300 mm Wide Air Conditioner Base......................................................................................................28
4.1.2.2 Deploying Bases for a 600 mm wide IT Cabinet/Battery Cabinet/Network Cabinet ..............................................30
4.1.2.3 Deploying the 600 mm Wide PDC Base.....................................................................................................................31
4.1.2.4 Deploying 800 mm Wide Fixed Bases........................................................................................................................33
4.1.2.5 Securing Bases..............................................................................................................................................................34
4.2 Preparing for Installing Air Conditioners..........................................................................................................................36
4.2.1 Material Preparations.......................................................................................................................................................36

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
Contents
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
v
4.2.2 Checking the Air Pressure...............................................................................................................................................43
4.2.3 Installing Water Pipe Adapters........................................................................................................................................45
4.2.4 Removing Transportation Fasteners for theAir Conditioner........................................................................................47
4.3 Removing Pallets ................................................................................................................................................................48
4.3.1 Removing the PDC Pallet ...............................................................................................................................................49
4.3.2 Removing the IT Cabinet Pallet......................................................................................................................................51
4.3.3 Removing the Air Conditioner Pallet .............................................................................................................................52
4.4 Adjusting the Baffle Plate for the Air Conditioner...........................................................................................................53
4.5 (Optional) Adjusting IT Cabinet Side Plates.....................................................................................................................54
4.6 (Optional) Adjusting Battery Cabinet Side Plates ............................................................................................................55
4.7 (Optional) Installing the PDC Tail Frame .........................................................................................................................56
4.8 RoutingAir Conditioner Pipes...........................................................................................................................................60
5 Installing the Cabinet.......................................................................................................... 62
5.1 Installing Cabinets (with Bases) ........................................................................................................................................62
5.2 Positioning Cabinets (Without Bases)...............................................................................................................................65
5.3 Installing Cabinets (Without Bases)..................................................................................................................................66
5.4 Installing Cabinet Accessories ...........................................................................................................................................70
5.4.1 (Optional) Taking Out PDU2000 Cables and Industrial Connectors ...........................................................................70
5.4.2 (Optional) Installing Branch Ground Copper Bars........................................................................................................72
5.4.3 (Optional) Installing the Vertical Ground Bar................................................................................................................73
5.4.4 (Optional) Setting a Mechanical Coded Lock ...............................................................................................................74
6 Installing the Contained Aisles.......................................................................................... 77
6.1 Installing Sealing Plates .....................................................................................................................................................77
6.2 Installing Skylights .............................................................................................................................................................79
6.2.1 Skylight Overview...........................................................................................................................................................79
6.2.1.1 600 mm Wide Control Skylight...................................................................................................................................79
6.2.1.2 800 mm Wide Control Skylight...................................................................................................................................80
6.2.1.3 600 mm Wide Flat or Rotating Skylight .....................................................................................................................80
6.2.1.4 800 mm Wide Flat or Rotating Skylight .....................................................................................................................81
6.2.1.5 300 mm Wide Flat Skylight .........................................................................................................................................82
6.2.2 Securing Skylights...........................................................................................................................................................83
6.2.3 Installing a Rotating Skylight Magnetic Lock...............................................................................................................85
6.3 Installing End Doors...........................................................................................................................................................86
6.3.1 Installing a Cabinet Lower Mounting Kit ......................................................................................................................87
6.3.2 Installing a Revolving Door............................................................................................................................................89
6.4 Attaching Cabinet Labels ...................................................................................................................................................99
6.5 (Optional) Installing Aisle Lights ....................................................................................................................................101
7 (Optional) Installing the New Main Way ....................................................................... 104
8 (Optional) Installing Cable Troughs ............................................................................... 105
8.1 Installing a 600 mm Wide Cable Trough.........................................................................................................................105

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
Contents
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vi
8.2 Installing a 300 mm Wide Cable Trough.........................................................................................................................109
8.3 Installing an 800 mm Wide Cable Trough ......................................................................................................................111
9 Installing Monitoring Devices ......................................................................................... 112
9.1 Device Layout in the Network Cabinet...........................................................................................................................112
9.2 (Optional) Installing a Server...........................................................................................................................................113
9.3 (Optional) Installing a VCN500.......................................................................................................................................115
9.4 (Optional) Installing a LAN Switch ................................................................................................................................116
9.5 Installing an ECC800........................................................................................................................................................118
9.6 (Optional) Installing a Rack Environment Unit..............................................................................................................120
9.7 Installing Monitoring Components on a Control Skylight.............................................................................................121
9.7.1 Installing a Camera........................................................................................................................................................122
9.7.2 (Optional) Installing a Smoke Detector........................................................................................................................126
9.7.3 (Optional) Installing the Multi-Functional Sensor ......................................................................................................126
9.8 (Optional) Installing Monitoring Components on the End Door...................................................................................127
9.8.1 Monitoring Component Layout for the Revolving Door ............................................................................................127
9.8.2 Installing an Actuator or Converter..............................................................................................................................128
9.8.3 Installing an Alarm Beacon...........................................................................................................................................131
9.8.4 (Optional) Installing a Revolving Door Magnetic Lock.............................................................................................132
9.8.5 Installing Buttons...........................................................................................................................................................137
9.8.6 Installing the Pad Mounting Kit....................................................................................................................................138
9.8.6.1 Installing a Fingerprint and Card Reader..................................................................................................................139
9.8.6.2 Installing a Fingerprint and Card Reader with a Keypad.........................................................................................140
9.8.6.3 Installing a Card Reader with a Keypad ...................................................................................................................141
9.8.6.4 Installing an IC Card Reader......................................................................................................................................142
9.8.6.5 Installing a Pad Power Connector.............................................................................................................................144
9.8.6.6 Installing a Pad ...........................................................................................................................................................147
9.8.6.7 Securing the Pad Mounting Kit .................................................................................................................................148
9.9 (Optional) Installing a Smart ETH Gateway...................................................................................................................151
9.10 Installing Temperature Sensors......................................................................................................................................154
9.11 Rules for Deploying T/H Sensors..................................................................................................................................155
9.12 Installing a T/H Sensor...................................................................................................................................................157
9.13 Installing a WLDS900 Water Sensor (Used in Intelligent Micro-Modular)...............................................................159
9.13.1 Connecting a Cable to the WLDS900 Water Detector..............................................................................................159
9.13.2 Laying Out the Water Detection Cable (Top Pipe Routing) .....................................................................................161
9.13.3 Laying Out the Water Detection Cable (Bottom Pipe Routing) ...............................................................................163
10 (Optional) Installing In-Room Cable Trays.................................................................. 166
11 Installing Cabinet Sealing Plates................................................................................... 167
12 Cable Routing .................................................................................................................. 169
12.1 System Cabling Rules.....................................................................................................................................................169
12.2 Cable Routes for the Single-RowAisle Containment Scenario (Power Supply and Distribution Cabinet).............174

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
Contents
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vii
12.3 Cable Routes for the Single-Row Aisle Containment Scenario (New Main Way) ....................................................175
12.4 Cable Routing for Cabinet Door Monitoring Components..........................................................................................177
12.5 Cable Routing for the Network Cabinet........................................................................................................................178
12.6 Cable Routes for Revolving Door Monitoring Components.......................................................................................178
12.7 Cable Routes for the Aisle Lighting System.................................................................................................................179
12.8 Installing an SMS Modem .............................................................................................................................................181
12.9 Connecting the Ground Cables for the Smart Module.................................................................................................183
12.9.1 Grounding Cabinets.....................................................................................................................................................183
12.9.2 (Optional) Connecting Base Ground Cables..............................................................................................................185
12.10 Cable Installation for the Power Supply and Distribution System............................................................................187
12.10.1 Connecting Battery Cables .......................................................................................................................................187
12.10.2 Connecting Cables to Power Supply and Distribution Devices .............................................................................192
12.11 Connecting Cables for the Cooling System ................................................................................................................193
12.12 Connecting Cables for the Management System........................................................................................................193
13 Installation Verification.................................................................................................. 194
14 Power-On Commissioning ............................................................................................. 195
14.1 Power-On Commissioning Process ...............................................................................................................................195
14.2 Commissioning the Power Supply and Distribution System (Power Supply and Distribution Cabinet) .................195
14.3 Commissioning the Power Supply and Distribution System (New Main Way).........................................................196
14.4 Commissioning the Cooling System .............................................................................................................................196
14.5 Commissioning the Management System (Power Supply and Distribution Cabinet) ...............................................197
14.6 Commissioning the Management System (New Main Way).......................................................................................198
A Appendix ........................................................................................................................... 199
A.1 Contacting Huawei Technical Support (Carrier)............................................................................................................199
A.2 Installing Expansion Sleeves...........................................................................................................................................199
A.3 Installing a Floating Nut..................................................................................................................................................200
A.4 Preparing a Monitoring Cable.........................................................................................................................................201
A.5 Scenario with a Column (600 mm Wide ITCabinets Scenario)...................................................................................203
A.5.1 Scenario Description.....................................................................................................................................................203
A.5.2 Installation Process for Scenarios with Columns .......................................................................................................210
A.5.3 Installing a Cabinet Bottom Sealing Plate...................................................................................................................210
A.5.4 Installing Sealing Plates Near theAisle ......................................................................................................................211
A.5.5 Installing the Adjustable Skylight................................................................................................................................213
A.5.5.1 Installing the Skylight Connective Plate ..................................................................................................................214
A.5.5.2 Installing the Telescopic Edges.................................................................................................................................214
A.5.5.3 Installing an Adjustable Skylight Side Sealing Plate ..............................................................................................216
A.5.5.4 Installing the PC Plate Support and PC Plate ..........................................................................................................218
A.5.6 Installing Cable Trays...................................................................................................................................................221
A.5.7 Installing a Sealing Plates away the Aisle...................................................................................................................224
A.6 (Optional) Connecting Cables to Industrial Connectors ...............................................................................................225
A.7 (Optional) Connecting PDU2000 Cables.......................................................................................................................226

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
Contents
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
viii
A.8 Cable Routes Inside an IT Cabinet .................................................................................................................................230
A.9 (Optional) Connecting the Linkage Cables Between the Fire Extinguishing System and Access Actuator..............234
B Common Screw Torques .................................................................................................. 235
C Installation Verification................................................................................................... 237
D Acronyms and Abbreviation........................................................................................... 240

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1
1 Installation Preparations
1.1 Transportation and Placing Precautions
Air Conditioner Transportation Precautions
Only trained personnel are allowed to move the cabinet. Use a pallet truck to transport
the cabinet secured to a wooden support to the installation position. Insert the forks of
the pallet truck in the middle position to ensure balance.
Choose railways, sea, or a road with good condition during transportation. No excessive
tilt or jolt is allowed during the transportation, and the maximum tolerance of the tilting
angle during loading and unloading is 15°, as shown in Figure 1-1.
To prevent the cabinet from falling over, secure it to a pallet truck using ropes before
moving it.
To prevent shocks or falls, move the cabinet gently.
Move the equipment close to the installation site before unpacking. Unpack the
equipment with caution to avoid scratching or bumping. Take down the equipment from
the pallet only immediately before installation.
Figure 1-1 Transportation gradient

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2
Placing Precautions
Place the cartons in order based on the carton numbers, as shown in Figure 1-2.
Figure 1-2 Arranging components
1.2 Unpacking and Acceptance
Context
Unpack and inspect all cabinets, mechanical parts, and components. Check that all the items
are intact and comply with the packing list on the presence of both the project supervisor and
customer.
Procedure
Step 1 Unpack the carton labeled "Contain Packing List" and take out the Packing List.
Step 2 Check all items against the Packing List.
Step 3 If an item is incorrect or missing, contact Huawei technical support.
Step 4 If any item is damaged, fill in the Cargo Replacement Application Form and report it.

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3
Step 5 Sign on the Packing List with the customer after verifying that all required items are
delivered.
Step 6 Store the items properly.
----End
Follow-up Procedure
Put the items to be installed immediately onto an ESD surface, such as a polyethylene (PE)
bag or an expandable polyethylene (EPE) foam. Pack the items not to be installed
immediately with their original packing materials. Put them in a dry and cool environment
without exposure to sunlight or electromagnetic radiation.
1.3 Installation Environment Requirements
Ensure that the installation environment meets the requirements before installation.
Table 1-1 Installation environment checklist
Check Item
Requirement
Check Result
Floor bearing
capacity
Standard live load of the equipment
room: 8–12 kN/m2(If the battery
cabinet is contained in the module,
use the standard live load of the
equipment room as a reference.)
Suspended load of the equipment
room: 1.2 kN/m2
Standard live load of the UPS room:
8–10 kN/m2
Standard live load of the battery
room: 16 kN/m2
Standard live load of the monitoring
center: 6 kN/m2
□ Compliant □
Incompliant
Equipment room net
height
See the field requirements for details.
□ Compliant □
Incompliant
Device passage and
door height and
width
Height ≥ 2.2 m and width ≥ 1.2 m
□ Compliant □
Incompliant
Floor levelness
Allowed deviation: 3 mm/2000 mm
□ Compliant □
Incompliant
Elevator
Elevator bearing capacity > 1.5 t
Inner dimensions: height > 2.4 m or
depth > 2.7 m
□ Compliant □
Incompliant
Cable tray
Preinstalled in the equipment room for
signal cables and power cables
□ Compliant □
Incompliant

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
Check Item
Requirement
Check Result
Power supply
380–415 V AC, 3-phase, 50/60 Hz
□ Compliant □
Incompliant
Fire extinguishing
Indoor gaseous fire extinguisher
□ Compliant □
Incompliant
Floor drain
DN50 or larger, made of cast iron or
stainless steel
□ Compliant □
Incompliant
Module grounding
The equipment room grounding
system must be a TN-S or TN-C-S
system
The equipment room ground grid
must have a ground resistance of 10
ohms at most (If the ground
resistance exceeds 10 ohms, ensure
that the equivalent ground radius of
the ground grid exceeds 5 m.)
Ground bars must be deployed over
the cable tray or under the raised
floor
□ Compliant □
Incompliant
Monitoring port
One LAN switch Ethernet port:
connects to the customer subnet to
monitor devices inside the module.
(Optional) Two fire control dry
contacts (access actuator and PDC
fire control terminal): connect to the
fire extinguishing system of the
equipment room for interaction.
SIM card: supports 3G (WCDMA)
communication and is compatible
with 2G (GSM) communication. At
least one SIM card is available.
NOTE
The prerequisite for using a SIM card is that
the site has signal coverage.
IP address: At least one IP address
for the ECC collector, the camera,
and the VCN respectively.
NOTE
An IP address is required for each camera.
□ Compliant □
Incompliant
If any of the requirements is not met, contact Huaweitechnical support.

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
1.4 Site Requirements (Power Supply and Distribution
Cabinet)
Equipment Room Height Requirement
The net height of an equipment room must not be lower than 2600 mm in the case of a single-
row aisle containment. Figure 1-3 shows the height of each component in the smart module.
The maximum height of the module is the height when the skylight is open. The maximum
height is not exceeded if the camera support or fire extinguisher support is installed.
The clearance for fire extinguishing nozzles is subject to specific fire extinguishing
requirements and is not considered in this section.
Figure 1-3 Smart module height
Cabinet height L1: 2000 mm
Open-skylight height L2: 550 mm
When the base is configured, the equipment room net height equals the equipment room net
height (without base) plus the base height.

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
Smart module layout requirement
Figure 1-4 shows the layout requirement for the smart module.
Figure 1-4 Smart module layout requirement
1.5 Site Requirements (New Main Way)
Equipment Room Height Requirement
Figure 1-5 shows the height of each component in single-row aisle containment if 2000 mm
high cabinets and the new main way are used.
The clearance for fire extinguishing nozzles is subject to specific fire extinguishing
requirements and is not considered in this section.
Table 1-2 Equipment Room Net Height Requirement (Without Base)
Scenario
Equipment room net height
2000 mm high cabinets and the new main
way
> 2800 mm

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
When the base is configured, the equipment room net height equals the equipment room net
height (without base) plus the base height.
Figure 1-5 Smart module height
Cabinet height L1: 2000 mm
First row new main way height L2: 455
mm
Second row new main way height L3: 675
mm
Smart module layout requirement
Figure 1-6 shows the layout requirement for the smart module.

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
Figure 1-6 Smart module layout requirement
1.6 Documents
Before installation, prepare the following documents in addition to this document.
Table 1-3 Documents for hardware installation
Documentation
Purpose
Obtaining Method
(Remarks)
Onsite engineering layout
drawing
Describes the cabinet
layout.
Provided by the engineering
designer or technical support
engineer.
Quick Reference Guide to
the Smart Modular Data
Center
Smart Module Quick
Installation Guide
describes the unpacking
sequence, installation
procedure, and
installation precautions.
Smart Module
Management System
Wiring Diagram
describes how to route
cables for the
management system.
The document is delivered
with the device, or you can
click Download.
UPS5000-E-(40 kVA–128
kVA) Quick Guide
(Integrated UPS 2.0)
Describes the installation,
cable connection, and
power-on operations for the
integrated UPS.
The document is delivered
with the device, or you can
click Download.
PDU8000 Modular
Precision PDC Quick Guide
Describes the installation,
cable connection, and
The document is delivered
with the device, or you can

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
Documentation
Purpose
Obtaining Method
(Remarks)
(1100 mm Deep)
power-on operations for the
PDU8000 Precision PDC.
click Download.
NetCol5000-C 30 kW
Chilled Water In-Row
Precision Air Conditioner
Quick Guide (Simplified
Edition)
Describes the installation
and cable connection for
the NetCol5000-C 30 kW
air conditioners.
The document is delivered
with the device, or you can
click Download.
New Main Way Quick
Guide
Describes how to install the
new main ways.
Delivered with new main
way.
Indoor Cable Tray
Installation Guide
Describes how to install the
in-room cable trays.
Click Download.
Smart Module Battery
Wiring Diagram
Provides guidance about
battery arrangement and
cable connections.
Delivered with battery
cables.
iBAT 2.0-CIM01C2 User
Manual
Describes the installation,
cable connection, and
power-on operations for the
CIM and BIM.
Click Download.
ECC800 Data Center
Controller (ECC Version)
User Manual
Describes the overview of
the ECC800 and its ports,
installation, commissioning,
user interfaces,
maintenance, and
troubleshooting.
The ECC version depends on
the version in use. Click
on the ECC800 WebUI to
obtain the ECC version in
use. Click Download.
iManager NetEco Device
Commissioning Guide-
(NetEco Version)
Describes how to connect
monitoring hardware to the
NetEco.
The NetEco version depends
on the version in use. Click
on the NetEco WebUI to
obtain the NetEco version in
use. Click Download.
iManager NetEco Product
Document - (NetEco
Version)
Describes how to install
monitoring hardware and
configure monitoring
software.
The NetEco version depends
on the version in use. Click
on the NetEco WebUI to
obtain the NetEco version in
use. Click Download.
1.7 Tools and Instruments
This section lists the tools and instruments required for installation.

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
Table 1-4 General tools
Name, Specifications, and Appearance
Protective gloves
Marker
Measuring tape (5
m)
Level
Step ladder (2 m)
Phillips screwdriver
(M4, M6, and M8)
Phillips screwdriver
M4 (length < 100
mm)
Flat-head
screwdriver (2–5
mm)
Adjustable wrench
(6")
Socket wrench
M4/M6/M8/M12
Hex key
Box-end wrench
(M6, M8, and M12)
Torque wrench (28
mm)
Solid wrench
(12#/13#/18#)
Cotton cloth
Labels
Electric screwdriver
Hand drill (Φ3,
Φ3.7, Φ4, Φ4.5, Φ5,
Φ6, Φ10, and Φ12
drill bits)
Hammer drill (Φ16
drill bit)
Heat gun
Laser locator
Electrician's knife
Impact tool
Polyvinyl chloride
(PVC) insulation

FusionModule5000 Smart Modular Data Center
Installation Guide (Single-Row Aisle Containment with
2000 mm High Cabinets, ECC800)
1 Installation Preparations
Issue 01 (2019-03-05)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
Name, Specifications, and Appearance
tape
Needle-nose pliers
Diagonal pliers
RJ45 crimping tool
Crimping tool
Wire stripper
Hydraulic pliers
Wire clippers
Cable ties
Multimeter
Electroprobe
Brush
Claw hammer
Vacuum cleaner
Hacksaw
Handsaw
Right angle
Heat shrink tubing
Network cable tester
Rubber mallet
Adjustable socket
screwdriver
Flashlight
Clamp meter
Phase sequence
meter
Utility knife