Huawei S1700-8G-AC User manual

Install the device on a worktable.
安装设备到工作台。
Mark the screw locations on the wall according to
the holes on the back of device.
根据设备后面板上的挂孔，用记号笔标记螺钉位置。
Rev: 02
膨胀套
Screw Ancrotron
膨胀套
Screw Ancrotron
技术支持
快速安装指南以及简易使用说明书
Service and Support
Installing the Device on a Worktable
安装设备到工作台
Tool List
工具参考
S1700-8G-AC以太网交换机
S1700-8G-AC Ethernet Switch
User Manual & Installation Quick Start
Crosshead screwdriver
十字螺丝刀
羊角锤
Claw hammer
Marker pen
记号笔
电源适配器
Power adapter
Installing the Device on a Wall
安装设备到墙面
M6螺钉
M6 screw
Accessories (S1700-8*-AC)
设备附件介绍( S1700-8G-AC ）
Percussion drill(φ8 Drill bit)
冲击钻（φ8钻头）
φ8 Drill bit
φ8钻头
90。
Install the Screw Ancrotron.
安装膨胀套。
●To prevent injuries, check that there is no electrical wire at the locations to be drilled before drilling holes in the wall.
●
●
●
Flammable and explosive items under the device is prohibited. Leave more than 100 mm of space around the device for proper heat dissipation.
在墙上打孔时，必须确认打孔处没有墙电，避免造成人身伤害。
设备下方禁止摆放易燃易爆物品，距离设备100mm范围内不能有异物挡住。
4

Install the screws.
安装螺钉。
Connect the power adapter.
连接电源适配器
Install the device on the wall.
安装设备到墙面。
● Do not power on the device before device installation and cabling are completed.
●The S1700-8G-AC can use only DC power supply.
●The power input of S1700-8G-AC is 12V/0.5A.
● 严禁在设备安装和布线完成前向设备供电。
●S1700-8G-AC只支持附带的电源适配器。
● S1700-8G-AC电源输入为12V/0.5A。
Connecting Power Adapter
连接电源适配器
12V0.5A
12V 0.5A
12V 0.5A
12V 0.5A
5

设备连接到网络接口。
Connect the device to network interface.
设备连接到计算机。
Connect the device to the computer.
设备上电。
Power on the device.
Laying out Cables
布放线缆
12V 0.5A
12V 0.5A
6

LED Indicator
LED状态
LED Condition
状态
Description
描述
PWR On Green
绿色常亮
On Green
绿色常亮
Internal power is operating normally.
设备正常上电。
Off
熄灭
Power off.
设备未上电。
1-8 Port
Blinking Green
绿色闪烁
The port has a valid 1000Mbps link.
Blinking indicates activity.
闪烁表示正在传输数据。
On Yellow
黄色常亮
Blinking Yellow
黄色闪烁
The port has a valid 10/100Mbps link.
Blinking indicates activity.
闪烁表示正在传输数据。
Off
熄灭
No link.
无效连接。
端口建立了1000Mb连接。
端口建立了10/100Mb连接。
● After the device is powered on, the PWR LED is on. the port LED status is as shown in below.
● 设备上电后，PWR电源指示灯亮，端口LED灯状态如下图所示。
PWR LED
电源指示灯
Ports LED
端口指示灯
Powering on the System
上电检查
7