Huawei Quidway S5600 User manual

HUAWEI
Quidway S5600 Series Ethernet Switches
Installation Manual
VRP3.10
Huawei Technologies Proprietary

Quidway S5600 Series Ethernet Switches
Installation Manual
Manual Version T2-080470-20060105-C-1.04
Product Version VRP3.10
BOM 3104A070
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support
and service. If you purchase the products from the sales agent of Huawei Technologies Co.,
Ltd., please contact our sales agent. If you purchase the products from Huawei
Technologies Co., Ltd. directly, Please feel free to contact our local office, customer care
center or company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co., Ltd.,
Bantian, Longgang District, Shenzhen, P. R. China
Postal Code: 518129
Website: http://www.huawei.com
Huawei Technologies Proprietary

Copyright © 2006 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks
, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess, ETS, DMC,
TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, M900/M1800,
TELESIGHT, Quidview, Musa, Airbridge, Tellwin, Inmedia, VRP, DOPRA,
iTELLIN, HUAWEI OptiX, C&C08iNET, NETENGINE, OptiX, iSite, U-SYS, iMUSE,
OpenEye, Lansway, SmartAX, infoX, and TopEng are trademarks of Huawei
Technologies Co., Ltd.
All other trademarks and trade names mentioned in thismanual are the property of
their respective holders.
Notice
The information in this manual is subject to change without notice. Every effort has
been made in the preparation of this manual to ensure accuracy of the contents,
but all statements, information, and recommendations in this manual do not
constitute the warranty of any kind, express or implied.
Huawei Technologies Proprietary

About This Manual
Release Notes
This manual applies to VRP3.10.
Related Manuals
The related manuals are listed in the following table.
Manual Content
Quidway S5600 Series Ethernet
Switches Operation Manual
It provides information of getting started, port,
VLAN, network protocol, routing protocol,
multicast protocol, QoS/ACL, IRF Fabric, MSTP,
security, system management, HWPing and
PoE.
Quidway S5600 Series Ethernet
Switches Command Manual
It provides the command of getting started, port,
VLAN, network protocol, routing protocol,
multicast protocol, QoS/ACL, IRF Fabric, MSTP,
security, system management, HWPing and
PoE.
Organization
There are seven chapters in the manual.
Chapter 1 Product Overview gives a brief introduction to S5600 Series Ethernet
Switches.
Chapter 2 Preparing for Installation introduces such topics as the precautions and
the environmental requirements of S5600 Series Ethernet Switches, the instructions
for the installation, the installation tools and so on.
Chapter 3 Installing the Switch introduces the installation of the S5600 Series
Ethernet Switches, module installation, connections of the power cable, ground wire
and the console cable.
Chapter 4 Starting up the Switch at the Initial Boot introduces the booting process
of S5600 Series Ethernet Switches, including the power-on booting of the switch and
the system initialization.
Huawei Technologies Proprietary

Chapter 5 Loading Boot ROM and Host Software introduces how to load
BootROM and host software for S5600 Series Ethernet Switches.
Chapter 6 Maintenance and Troubleshooting introduces the problems that might
occur during the installation and the booting of S5600 Series Ethernet Switches and
the related solution.
Appendix A Lightning Protection of the Switch introduces lightning arrester for AC
power and lightning arrester for network port.
Intended Audience
The manual is intended for the following readers:
zNetwork engineers
zNetwork administrators
zCustomers who are familiar with network fundamentals
Conventions
The manual uses the following conventions:
I. General conventions
Convention Description
Arial Normal paragraphs are in Arial.
Boldface Headings are in Boldface.
Courier New
Terminal Display is in Courier New.
II. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
Huawei Technologies Proprietary

Convention Description
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
# A line starting with the # sign is comments.
III. GUI conventions
Convention Description
< > Button names are inside angle brackets. For example, click
the <OK> button.
[ ] Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
/ Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
IV. Keyboard operation
Format Description
<Key> Press the key with the key name inside angle brackets. For
example, <Enter>, <Tab>, <Backspace>, or <A>.
<Key1+Key2> Press the keys concurrently. For example, <Ctrl+Alt+A>
means the three keys should be pressed concurrently.
<Key1, Key2> Press the keys in turn. For example, <Alt, A> means the
two keys should be pressed in turn.
Huawei Technologies Proprietary

V. Mouse operation
Action Description
Select Press and hold the primary mouse button (left mouse
button by default).
Click Select and release the primary mouse button without
moving the pointer.
Double-Click Press the primary mouse button twice continuously and
quickly without moving the pointer.
Drag Press and hold the primary mouse button and move the
pointer to a certain position.
VI. Symbols
Eye-catching symbols are also used in the manual to highlight the points worthy of
special attention during the operation. They are defined as follows:
Caution,Warning, Danger: Means reader be extremely careful during the
operation.
Note,Comment, Tip,Knowhow,Thought: Means a complementary
description.
Environmental Protection
This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.
Huawei Technologies Proprietary

Installation Manual
Quidway S5600 Series Ethernet Switches Table of Contents
Huawei Technologies Proprietary
i
Table of Contents
Chapter 1 Product Overview........................................................................................................1-1
1.1 Introduction ........................................................................................................................ 1-1
1.2 S5624P/S5624P-PWR/S5624F Ethernet Switch............................................................... 1-3
1.2.1 Front Panel.............................................................................................................. 1-3
1.2.2 Rear Panel ............................................................................................................ 1-12
1.2.3 Expansion Module................................................................................................. 1-13
1.3 S5648P/S5648P-PWR Ethernet Switch .......................................................................... 1-17
1.3.1 Front Panel............................................................................................................ 1-17
1.3.2 Rear panel............................................................................................................. 1-18
1.3.3 Expansion Module................................................................................................. 1-19
1.4 S5600 Series Technical Specifications ........................................................................... 1-22
Chapter 2 Preparing for Installation............................................................................................2-1
2.1 Safety Precautions............................................................................................................. 2-1
2.2 Installation Site................................................................................................................... 2-1
2.2.1 Temperature/Humidity............................................................................................. 2-1
2.2.2 Cleanness ............................................................................................................... 2-2
2.2.3 Electromagnetic Susceptibility ................................................................................ 2-2
2.2.4 Laser Safety ............................................................................................................ 2-3
2.3 Installation Tools................................................................................................................ 2-3
Chapter 3 Installing the Switch....................................................................................................3-1
3.1 Mounting the Switch in a Rack or on a Tabletop ............................................................... 3-1
3.1.1 Rack-Mounting the Switch ...................................................................................... 3-1
3.1.2 Mounting the Switch on a Tabletop/Workbench ..................................................... 3-3
3.2 Installing/Removing the Power Module ............................................................................. 3-4
3.2.1 Installing the Power Module.................................................................................... 3-4
3.2.2 Removing the Power Module .................................................................................. 3-4
3.3 Connecting the Power Cord and the Ground Wire............................................................ 3-5
3.3.1 Connecting the AC-Input Power Cord..................................................................... 3-5
3.3.2 Connecting the DC-Input Power Cord .................................................................... 3-6
3.3.3 Connecting the Ground Wire................................................................................... 3-7
3.4 Connecting the Switch to a Console Terminal................................................................... 3-9
3.4.1 Console Cable......................................................................................................... 3-9
3.4.2 Connecting the Console Cable ............................................................................. 3-10
3.5 Installing/Removing the Stack Cable ............................................................................... 3-11
3.5.1 Stack Cable ........................................................................................................... 3-11
3.5.2 Installing the Stack Cable...................................................................................... 3-11
3.5.3 Removing the Stack Cable.................................................................................... 3-11

Installation Manual
Quidway S5600 Series Ethernet Switches Table of Contents
Huawei Technologies Proprietary
ii
3.6 Installing/Removing the Optional Interface Module ......................................................... 3-12
3.7 Verifying Installation......................................................................................................... 3-13
Chapter 4 Starting up the Switch at the Initial Boot .................................................................. 4-1
4.1 Setting up a Configuration Environment............................................................................ 4-1
4.2 Connecting the Console Cable .......................................................................................... 4-1
4.3 Setting Terminal Parameters ............................................................................................. 4-1
4.4 Booting the Switch ............................................................................................................. 4-5
4.4.1 Verifying Installation before Power-up .................................................................... 4-5
4.4.2 Powering up the Switch........................................................................................... 4-5
Chapter 5 Loading Boot ROM and Host Software ..................................................................... 5-1
5.1 Introduction to Loading Approaches.................................................................................. 5-1
5.2 Loading Software Locally................................................................................................... 5-1
5.2.1 Boot Menu ............................................................................................................... 5-1
5.2.2 Loading Software from Console Port Using XModem ............................................ 5-3
5.2.3 Loading Software from an Ethernet Port Using TFTP ............................................ 5-7
5.2.4 Loading Software from an Ethernet Port Using FTP............................................... 5-9
5.3 Loading Software Remotely............................................................................................. 5-10
5.3.1 Loading Software Remotely Using FTP ................................................................ 5-10
5.3.2 Loading Software Remotely Using TFTP.............................................................. 5-11
Chapter 6 Maintenance and Troubleshooting............................................................................6-1
6.1 Dealing with Loading Failures............................................................................................ 6-1
6.2 Dealing with Password Loss.............................................................................................. 6-1
6.3 Dealing with Power System Failures ................................................................................. 6-1
6.4 Dealing with Configuration System Failures...................................................................... 6-1

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-1
Chapter 1 Product Overview
1.1 Introduction
Quidway S5600 Series Ethernet Switches are wire speed Layer2/3 Ethernet switches
developed independently by Huawei Technologies Co., Ltd. These intelligent and
network manageable switches are intended to be used in the network environments
that require high performance, dense port distribution, and ease of installation.
Currently, Quidway S5600 series include the following models:
zS5624P: Adopts AC/DC dual input power module (PSL130-AD). Its rear panel
provides two fixed fabric ports and one expansion module slot that is compatible
with 8-port 1000 Mbps SFP, 1-port 10 Gbps XENPAK, and 2-port 10 Gbps XFP
modules. Its front panel provides 24 x 10/100/1000Base-T auto-negotiation
Ethernet ports with RJ-45 connectors and four SFP Combo ports. Each Combo
port corresponds to an Ethernet port, so there are four port pairs; only one port in a
pair can be used at the same time. For the relationship between the Combo ports
and the Ethernet ports, refer to Table 1-1.
zS5624P-PWR: Adopts PoE power module (PSL480-AD24P, with external AC/DC
input). Its rear panel provides two fixed fabric ports and one expansion module slot
that is compatible with 8-port 1000 Mbps SFP, 1-port 10 Gbps XENPAK, and
2-port 10 Gbps XFP modules. Its front panel provides 24 x 10/100/1000Base-T
auto-negotiation Ethernet ports with RJ-45 connectors and four SFP Combo ports.
Each Combo port corresponds to an Ethernet port, so there are four port pairs;
only one port in a pair can be used at the same time. For the relationship between
the Combo ports and the Ethernet ports, refer to Table 1-1.
zS5624F: Adopts AC/DC dual input power module (PSL130-AD). Its rear panel
provides two fixed fabric ports and one expansion module slot that is compatible
with 8-port 1000 Mbps SFP, 1-port 10 Gbps XENPAK, and 2-port 10 Gbps XFP
modules. Its front panel provides 24 x 1000 Mbps SFP optical ports and four RJ-45
Combo ports. Each Combo port corresponds to a SFP port, so there are four port
pairs; only one port in a pair can be used at the same time. For the relationship
between the Combo ports and the Ethernet ports, refer to Table 1-1.
zS5648P: Adopts AC/DC dual input power module (PSL180-AD). Its rear panel
provides two fixed fabric ports and one expansion module slot that is compatible
with 8-port 1000 Mbps SFP, 1-port 10 Gbps XENPAK, and 2-port 10 Gbps XFP
modules. Its front panel provides 48 x 10/100/1000Base-T auto-negotiation
Ethernet ports with RJ-45 connectors and four SFP Combo ports. Each Combo
port corresponds to an Ethernet port, so there are four port pairs; only one port in a
pair can be used at the same time. For the relationship between the Combo ports
and the Ethernet ports, refer to Table 1-1.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-2
zS5648P-PWR: Adopts PoE power module (PSL480-AD48P, with external AC/DC
input). Its rear panel provides two fixed fabric ports and one expansion module slot
that is compatible with 8-port 1000 Mbps SFP, 1-port 10 Gbps XENPAK, and
2-port 10 Gbps XFP modules. Its front panel provides 48 x 10/100/1000Base-T
auto-negotiation Ethernet ports with RJ-45 connectors and four SFP Combo ports.
Each Combo port corresponds to an Ethernet port, so there are four port pairs;
only one port in a pair can be used at the same time. For the relationship between
the Combo ports and the Ethernet ports, refer to Table 1-1.
Table 1-1 Combo port list
Switch model Combo Port Corresponding port
25 22
26 24
27 21
S5624P/S5624P-PWR/S
5624F
28 23
49 46
50 48
51 45
S5648P/S5648P-PWR
52 47
Note:
zThe electrical ports of S5624P-PWR/S5648P-PWR are capable of supplying -48
VDC power to remote PDs (powered devices, such as S2016C, S2008B, S2016B,
S2016-EI, and so on).
zThe S5624P-PWR/S5648P-PWR adopts PoE power module, which provides
AC/DC power to PD devices. When delivering the AC input, the module can supply
up to 300 W power. If more power is needed, use the DC input or both AC and DC
inputs to ensure the operation of all the connected devices.
zThe S5624P-PWR/S5648P-PWR can also adopt AC/DC dual input power module.
In this case, however, the two types of switches have no PoE function. And they
function exactly like the S5624P and S5648P.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-3
1.2 S5624P/S5624P-PWR/S5624F Ethernet Switch
1.2.1 Front Panel
I. Front panel
The S5624P/S5624P-PWR provides 24 x 10/100/1000Base-TX Ethernet ports, one
Console port, and four 1000 Mbps SFP Combo ports on its front panel, as shown in
Figure 1-1:
(1) 24 x 10/100/1000Base-T auto-negotiation Ethernet port status LEDs
(2) 1000 Mbps SFP Combo port LED (3) Fabric LED
(4) RPS LED (5) Power LED
(6) Module LED (7) Port mode LED
(8) Mode button (9) 7-segment digitron display
(10) Console port
Figure 1-1 Front panel of the S5624P/S5624P-PWR
The S5624F provides 24 x 1000 Mbps SFP optical ports, one Console port, and four
1000 Mbps RJ-45 Combo ports on its front panel, as shown in Figure 1-2.
(1) SFP optical port status LED
(2) 1000 Mbps RJ-45 Combo port LEDs: left one for speed, right one for duplex mode
(3) Console port (4) 7-segment digitron display
(5) Power LED (6) RPS LED
(7) Fabric LED (8) Module LED
Figure 1-2 Front panel of the S5624F

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-4
II. LEDs
The S5624P/S5624P-PWR provides one power LED, one RPS LED, one fabric LED,
one module LED, one mode LED, one 7-segment digitron display, four pairs of 1000
Mbps SFP port status LEDs, and 24 pairs of 10/100/1000Base-T port status LEDs on
its front panel.
The S5624F provides one power LED, one RPS LED, one fabric LED, one module LED,
one 7-segment digitron display, 24 pairs of 1000 Mbps SFP port status LEDs, and four
pairs of RJ-45 Combo port status LEDs on its front panel.
Table 1-2 and Table 1-3 describe respectively the LEDs on the S5624P/S5624P-PWR
and S5624F.
Table 1-2 LEDs on the S5624P/S5624P-PWR
LED Mark Status Description
Speed Solid green The port status LEDs are
showing the speed of each port.
Duplex Solid yellow The port LEDs are showing the
duplex mode of each port.
Mode LED Mode
PoE Blinking green
(at 1 Hz)
The port LEDs are showing the
PoE status of each port.
Solid green The switch is started normally.
Blinking green (at 1 Hz) The system is running power-on
self-test (POST).
Solid red The system fails the POST, or
there is another fault.
Blinking yellow (at 1 Hz) Some ports fail the POST and
do not function.
Power LED PWR
OFF The switch is power-off.
Solid green Both the AC power supply and
the DC input operate normally.
Solid yellow
The AC power supply fails or the
AC input is disconnected, while
the DC input operates normally.
DC LED RPS
OFF DC input is disconnected.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-5
LED Mark Status Description
Green
The device is in the ring fabric
status; the LED blinks quickly
when the fabric port is receiving
or sending data.
Yellow
The device is in the daisy chain
fabric status; the LED blinks
quickly when the fabric port is
receiving or sending data.
Blinking green (at 3 Hz)
This device is isolated from the
whole set of fabric devices
(effective when this device is in
the fabric status).
Fabric LED STK
OFF Neither of the two fabric ports is
connected.
Solid green The module is seated and
operates normally.
Blinking yellow The module fails or is not
supported.
Module
LED
Modul
e
(MOD
)
OFF No module is installed.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-6
LED Mark Status Description
POST
running
Blinking
green
The POST ID of the in-process
test is displayed:
POST failed Blinking
red
The POST ID of the failed test
blinks.
Software
downloading
Blinking
green
A light bar rotates clockwise
around the display during the
downloading procedure.
Fan failed Solid red
An “F” is displayed.
Over
temperature
alarm
Solid red
A “t” is displayed.
Speed and
duplex mode
Solid
green
UNIT ID in the fabric; or “1” for a
standalone unit is displayed.
7-segment
digitron
display
Unit
PoE mode Solid
green
The utilization of the power
supply is displayed.
0 - 20%
21 - 40%
41 - 60%
61 - 80%
81 - 100%

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-7
LED Mark Status Description
Green
The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.
Yellow
The port is operating at 10/100
Mbps. The LED blinks quickly
when the port is receiving or
sending data.
Blinking
yellow
(at 3 Hz)
The port fails the POST.
Speed mode
OFF The port is not connected.
Green
The port is operating in full
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.
Yellow
The port is operating in half
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.
Blinking
Yellow
(3 Hz)
The port fails the POST.
Duplex mode
OFF The port is not connected.
Solid
green
The port supplies power
normally.
Blinking
green
(at 1 Hz)
The connected device requires
more power than the maximum
power a port can supply.
The port cannot supply power
because the switch has reached
its maximum power supplied.
Solid
yellow
The port cannot supply power
because the connected device is
not a PD.
The port cannot supply power
due to the power source failure
of PoE.
Blinking
yellow (3
Hz)
The port fails the POST.
10/100/100
0BASE-T
port status
LED
PoE mode
OFF The port does not supply power.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-8
LED Mark Status Description
Green
The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.
Blinking
yellow (3
Hz)
The port fails the POST.
Speed mode
OFF The port is not connected.
Green
The port is operating in 1000
Mbps full duplex mode. The LED
blinks quickly when the port is
receiving or sending data.
Blinking
yellow (3
Hz)
The port fails the POST.
Duplex mode
OFF The port is not connected.
1000Base
SFP port
mode LED
PoE mode OFF –
Table 1-3 LEDs on the S5624F
LED Mark Status Description
Solid green The switch is started normally.
Blinking green (at 1 Hz) The system is running power-on
self-test (POST).
Solid red The system fails the POST, or
there is another fault.
Blinking yellow (at 1 Hz) Some ports fail the POST and
do not function.
Power
LED PWR
OFF The switch is power-off.
Solid green Both the AC power supply and
the DC input operate normally.
Solid yellow
The AC power supply fails or the
AC input is disconnected, while
the DC input operates normally.
DC LED RPS
OFF DC input is disconnected.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-9
LED Mark Status Description
Green
The device is in the ring fabric
status; the LED blinks quickly
when the fabric port is receiving
or sending data.
Yellow
The device is in the daisy chain
fabric status; the LED blinks
quickly when the fabric port is
receiving or sending data.
Blinking green (at 3 Hz)
This device is isolated from the
whole set of fabric devices
(effective when this device is in
the fabric status).
Fabric
LED STK
OFF Neither of the two fabric ports is
connected.
Solid green The module is seated and
operates normally.
Blinking yellow The module fails or is not
supported.
Module
LED
Module
(MOD)
OFF No module is installed.
POST
running
Blinking
green
The POST ID of the in-process
test is displayed:
POST failed Blinking
red
The POST ID of the failed test
blinks.
Software
downloading
Blinking
green
A light bar rotates clockwise
around the display during the
downloading procedure.
Fan failed Solid red
An “F” is displayed.
Over
temperature
alarm
Solid red
A “t” is displayed.
7-segmen
t digitron
display
Unit
Speed and
duplex mode
Solid
green
UNIT ID in the fabric; or “1” for a
standalone unit is displayed.

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-10
LED Mark Status Description
Green
The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.
Yellow
The port is operating at 10/100
Mbps. The LED blinks quickly
when the port is receiving or
sending data.
Blinking
yellow
(at 3 Hz)
The port fails the POST.
Speed mode
OFF The port is not connected.
Green
The port is operating in full
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.
Yellow
The port is operating in half
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.
Blinking
Yellow
(3 Hz)
The port fails the POST.
RJ-45
Combo
port mode
LED
Duplex mode
OFF The port is not connected.
Green
The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.
Blinking
yellow (3
Hz)
The port fails the POST.
1000Base
SFP
optical
port status
LED
port status
LED
OFF The port is not connected.
III. Console port
The S5624P/S5624P-PWR/S5624F provides an EIA/TIA-232-compliant Console port,
which enables you to configure the switch from the local or remote site.
Table 1-4 Attributes of the Console port
Item Description
Connector RJ-45
Standard EIA/TIA-232

Installation Manual
Quidway S5600 Series Ethernet Switches Chapter 1 Product Overview
Huawei Technologies Proprietary
1-11
Item Description
Baud rate 9600 bps (default), auto-negotiation is supported
Services
Connection to an ASCII terminal
Connection to the serial port of a local terminal (a PC for
example) or a remote terminal (through a pair of modems)
running terminal emulation software
IV. Attributes of 1000 Mbps SFP port
The S5624P/S5624P-PWR provides four SFP Combo ports on its front panel, each one
corresponding to a 10/100/1000Base-T auto-negotiation Ethernet port. For each
corresponding pair, only one port can be used at the same time. The number of the SFP
Combo ports and the type of the SFP module are optional. For the relationship between
the Combo ports and the Ethernet ports, refer to Table 1-1
The S5624F provides 24 ×1000 Mbps SFP ports on its front panel.
SFP modules allow for great flexibility in networking because they are hot swappable
and user configurable.
The following table lists the available SFP modules that you can select as required:
Table 1-5 Specifications of 1000 Mbps SFP port cable
SFP module Central wavelen
gth
Connec
tor Fiber specification
Maximum
transmission
distance
50/125 µm
multi-mode
optical fiber
550 m (1804.5
ft.)
1000BASE-SX-SFP 850 nm
62.5/125 µm
multi-mode
optical fiber
275 m (902.2
ft.)
1000BASE-LX-SFP 10 km (6.2 mi)
1000BASE-LH-SFP
1310 nm
30 km (18.6 mi)
1000BASE-ZX-LR-SFP 40 km (24.9 mi)
1000BASE-ZX-VR-SFP
1550 nm
LC
Single-mode
fiber
70 km (43.5 mi)
1000BASE-T-AN-SFP —RJ-45
Category-5
twisted pair
cable
100 m (328 ft)