Huawei S1700 Series Operating and maintenance manual

HUAWEI TECHNOLOGIES CO., LTD.
S1700 Series Switches
Installation Quick Start
Issue: 04 (2020-12-30)
Part Number: 31507302

1
3 Safety Guidelines
4 Installing the Switch
S1700 series switches are Class A products. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Take ESD protection measures before the installation, for example, wear ESD gloves or ESD wrist strap.
Do not place other objects on the chassis.
2 Packing List
Scenario 1: Installing the Switch in a 19'' Cabinet/Rack
The floating nuts and M6 screws are not delivered with the switch and need to be separately
purchased if needed.
S1700 series switches use forced or natural heat dissipation mode. If multiple switches are installed in
a cabinet/rack, leave at least 1 U (44.45 mm) distance between each two switches. This distance is
recommended for switches using forced heat dissipation, and a distance greater than 1 U is required
for switches using natural heat dissipation.
The following table lists the mapping between mounting brackets and switch models.
Before You Start
Thank you for purchasing Huawei S1700 series switches. This guide describes the installation and cable
connections of S1700 series switches. Figures in the document are for reference only and may not show
the actual appearance of the switches.
AppearanceName Device Model
S1700-16R, S1700-24R, S1700-24GR, S1700-26R-2T, S1700-28GR-4X,
S1700-52GR-4X, S1720GFR series, S1720X series, S1720X-E series,
S1720GWR series, S1720GWR-E series
Mounting bracket A
Mounting bracket B
Middle mounting bracket A
Middle mounting bracket B
S1728GWR-4P, S1700-28FR-2T2P-AC, S1700-28GFR-4P-AC,
S1700-52FR-2T2P-AC, S1700-52GFR-4P-AC, S1700-52R-2T2P-AC,
S1720-10GF-2P, S1720-10GW-2P, S1720-10GW-2P-E
S1720-10GF-PWR-2P, S1720-10GW-PWR-2P, S1720-10GW-PWR-2P-E
S1700-16G, S1700-24-AC, S1724G
1 About This Guide
Chassis ground cable (only for S1720 PoE models)
Chassis (with the product model on the nameplate)
AC power cable Installation accessory package:
- M4 screws- Mounting brackets
- Quick Start Guide
- Rubber pads

2
Installation Procedure
Step 1
Step 2
Step 3
Scenario 2: Installing the Switch on a Desk
Attach the rubber pads to the switch. The rubber pads are of dierent shapes depending on
the switch models but are attached to switches in the same way.
Install the switch on a desk.
(Optional) Install a security lock. You can use a security lock to fix the switch on the desk. The
security lock needs to be purchased separately.
Step 1
Step 2
Step 3
12345678910 11 12 13 14 15 16
25
1G/STACK-5G
S1700V2-28GFR-2TP2P-AC
26
1G
27
1G
28 CONSOLE
12345678910 11 12 13 14 15 16
25 26 27
1G
28
1G
CONSOLE
S1720-28GFR-4TP-AC
MODE
1G/STACK-5G
1 U
≥ 1 U
12345678910 11 12 13 14 15 16
25 26 27
1G
1G/STACK-5G
Installing mounting bracket A Installing mounting bracket B Installing middle mounting bracket A
12345678910 11 12 13 14 15 16
25 26 27
1G
27
1G
CONSOLE
MODE
1G/STACK-5G
Installing middle mounting bracket B (Optional) Installing a long mounting bracket
Secure mounting brackets to the chassis with M4 screws. To install the S1720-10GW-2P, S1720-10GF-2P
and S1720-10GW-2P-E switches in a cabinet/rack, use the long mounting brackets (purchased separately)
shown in the following figure, instead of the short mounting brackets delivered with the switch by default.
Install floating nuts.
Secure the chassis onto the cabinet/rack with M6 screws. An S1720-20GFR-4TP switch is used as
an example here to illustrate the cabinet/rack mounting procedure.

3
CONSOLE
MODE
Installation Procedure
Step 1
Step 2
Step 3
Step 4
Before You Start
Scenario 3: Installing the Switch on a Wall
35 mm-40 mm
Installing mounting
bracket A
Installing mounting
bracket B
Installing the middle
mounting bracket
12345678910 11 12 13 14 15 16
25 26 27
1G
27
1G
1G/STACK-5G
Installing a long mounting
bracket
5 Connecting a Power Cable
Huawei switches must use optical modules that have been certified for use on Huawei switches.
The jack next to the AC power socket is reserved for an AC terminal locking latch. The AC terminal
locking latch is not delivered with a switch.
Before You Start
To prevent injuries, ensure that there is no electrical wire at the locations to be drilled before drilling
holes in the wall.
The panel with ports must face down to protect the ports from water.
Ensure that there are no flammable or explosive materials near the switch and no obstructions within
100 mm around the switch.
The expansion bolts need to be purchased separately.
An S1700-16R switch is used as an example here to illustrate the wall-mounting procedure.
Fix mounting brackets to both sides of the panel with ports using M4 screws.
Use a marker to mark the positions of mounting holes according to the size of the chassis and
positions of the mounting ears.
Install the expansion bolts in the wall.
Install the chassis on the wall.

Ground cable
4
To prevent injuries, do not connect a power cable while the power is on.
Connecting a Power Cable
6 Laying Cables
An AC terminal locking latch can prevent an AC power cable from failing or loosening. Secure an AC
cable with an AC terminal locking latch, as shown in the following figure.
Never look directly into an optical port. Optical fibers emit laser radiation that can cause eye damage.
The power cables must be more than 10 cm away from signal cables.
When a large number of cables need to be connected, arrange the cables in the cabinet, and then
install cable connectors.
S1720-20GFR-4TP
12345678910 11 12 13 14 15 16
25 26 27
1G
28
1G
CONSOLE
MODE
1G/STACK-5G
Ethernet cables Optical fibers
Fiber bundling tape
Cable tie
Grounding helps protect a switch from lightning, electromagnetic interference, and electrostatic discharge. A
PoE switch must be grounded before it provides power for a powered device (PD).
Connecting a ground cable: Connect the M4 lug of the ground cable to the ground screw of the switch, and
connect the M6 lug of the ground cable to the ground point of a cabinet or rack, or to a ground bar.
By default, no ground cable is delivered with a non-PoE switch. To ground a non-PoE switch using a ground
cable, purchase the ground cable separately.

5
S1700 series managed switches include the following models:
S1728GWR-4P, S1700-28FR-2T2P-AC, S1700-28GFR-4P-AC, S1700-52FR-2T2P-AC, and S1700-52GFR-4P-AC
If the web pages cannot be displayed properly, your web browser may need an upgrade. For details
about the web browser requirements, see the of the switch.
Before You Start
7 Indicator Description
8 Logging In to the Switch (Applicable to S1700 Series Managed Switches)
Power on the switch only when the input voltage is in the normal range (100 V AC to 240 V AC) to
test the AC input voltage of the switch.
The reset button (RST) is on the front panel of some switches. To restore the factory settings, press
and hold the reset button for more than 6 seconds. To restart a switch, press the reset button.
The MODE button on the front panel of some switches is used to switch the indicator mode to STAT,
SPED, or PoE.
Indicators on S1700 series switches have dierent meanings. For details, see the
The following table describes only the meanings of the PWR, SYS, and RUN indicators.
LED Indicator Color Description
System status indicator: SYS -
-
O: The system is not running.
System running status indicator: RUN Green Steady on: The system is starting or not working properly.
-O: The system is not running.
Blinking: The system is working properly.
Green Fast blinking: The system is starting.
Slow blinking: The system is operating properly.
Red Steady on: The system does not work properly after registration, or a fan
alarm or temperature alarm has been generated.
Green Steady on: The switch is powered on.
O: The switch is powered o.Power supply indicator: PWR
Login Procedure
Connect your computer to any Ethernet port of the switch using a network cable.
Open a web browser on the computer, enter https://192.168.1.253 (https://192.168.0.1 for
the S1728GWR-4P) in the address bar, and press Enter. The default username and password
are available in S Series Switches Default Usernames and Passwords. If you have not
obtained the access permission of the document, see Help on the website to find out how to
obtain it.
Step 1
Step 2
After you log in to the web system, the system home page is displayed.
Step 3
Login page of the S1728GWR-4P
S1700 Product
Description.
Web User Guide

6
Now, you can maintain the switch through the web system. For more information, see the Web System
Guide of the switch.
To ensure device security, change the default password immediately after logging in to the switch for the first time.
For security purposes, a password must contain at least two types of the following: lowercase letters, uppercase letters, digits,
and special characters (such as ! $ # %). In addition, the password cannot contain spaces or single quotation marks (').
To ensure device security, change the password periodically.
NOTE
If the web pages cannot be displayed properly, your web browser may need an upgrade. For details
about the web browser requirements, see the of the switch.
By default, the S1720GW, S1720GWR, and S1720X can only be managed using the web system of the
EasyOperation edition, whereas the S1720GF, S1720GFR-P, S1720GW-E, S1720GWR-E, and S1720X-E
can be managed using the web system of the EasyOperation edition, CLI, and SNMP.
The login page of the EasyOperation edition diers slightly from that in the figure in the following section.
Before You Start
9 Logging In to the Switch (Applicable to S1720 Series Switches)
Login Procedure
Connect your computer to any Ethernet port of the switch using a network cable. For the
S1720X and S1720X-E, connect the Ethernet cable to the ETH management port.
Configure an IP address for the computer, which must be on the same network segment as the
default IP address of the switch.
Open a web browser on the computer, enter
https://192.168.1.253 in the address bar, and
press Enter. The default username and password
are available in S Series Switches Default
Usernames and Passwords. If you have not
obtained the access permission of the document,
see Help on the website to find out how to obtain it.
Step 1
Step 2
Step 3 Change the password and re-log in to the
web system as prompted. You can manage
and maintain the switch on web pages
after logging in to the web system.
Step 4
Web User Guide
The password change page is displayed during the login process the first time you log in to the web system only when
the switch runs V200R009C00 or a later version.
The password change page is also displayed if your password will expire or has expired. To access the home page of the
web system, you must change the password.
For security purposes, a password must contain at least two types of the following: lowercase letters, uppercase letters, digits,
and special characters (such as ! $ # %). In addition, the password cannot contain spaces or single quotation marks (').
In V200R020C00 and later versions, the switch does not have a default web login password. You need to create a user
name and set a password when logging in to the web system for the first time.
NOTE

The quick configuration wizard is added to the web system of the EasyOperation edition in V200R010
and later versions. You can quickly perform the configurations of VLAN isolation and interconnection by
clicking the Switching or Routing buttons.
Now, you can use the web system to maintain the switch. For more information, see the
of the switch.
Log in to Huawei enterprise technical support website (https://support.huawei.com/enterprise),
and select a specific product model and version to find its documentation.
Log in to Huawei enterprise support community
(https://forum.huawei.com/enterprise/en/index.html) and post your questions in the
community.
10 Obtaining Product Documentation and Technical Support
Huawei Enterprise
Technical Support
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written consent
of Huawei Technologies Co., Ltd.
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Supplier’s Declaration of Conformity (SDoC)
Unique Identifier: trade name: HUAWEI; product name: Switch;
model number: S1700 series switches
Responsible Party- U.S. Contact Information
Huawei Technologies USA Inc.
5700 Tennyson Parkway, Suite 500
Plano, Texas 75024
Main: 214-919-6000 / TAC Hotline: [phone]
FCC Compliance Statement ( for products subject to Part 15)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Trademarks and Permissions
Qualification Card
PASS
Configuration
Guide
7
Open Source Software Notice
The Open Source Software Notice lists notices on open source software components used by the
product. Visit Huawei enterprise technical support website for the Open Source Software Notice.
After accessing the user management page, you can change the default user level. Users of level 3 or a higher level are
administrator users and have management rights. Users of level 2 or a lower level are monitored users. Administrator
users can perform any operations on web pages, and monitored users can only perform ping and tracert operations.