Huawei UPS5000-S Series User manual

1
Issue: 03
Part Number: 31509861
Date: 2019-06-10
UPS5000-S-(40 kVA-200 kVA)
Quick Guide (IP42, 40 kVA Power
Modules)
1Overview
Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
UPS Model Cabling
Mode Capacity Configuration Weight (Standard Configuration) Dimensions (H x W x D)
UPS5000-S-
200K-SM-IPB Bottom cable routing 200 kVA Net weight ≤ 480 kg
Gross weight ≤ 530 kg
2000 mm x 600 mm
x 850 mm
UPS5000-S-200K-SM
1. Before installation, read
the user manual
carefully to get familiar
with product information
and safety precautions.
2. Use insulated tools
during installation and
operation.
3. Only engineers certified
by Huawei or its agents
are allowed to install,
commission, and
maintain the UPS.
Otherwise, personal
injury or equipment
damage may occur, and
the UPS faults caused
are beyond the warranty
scope of Huawei.
4. This document
describes the
installation procedure
for a single UPS. For
details about how to
install a parallel system,
contact Huawei
technical support.
Power modules
Bypass module
Control module
Power distribution
subrack module
Monitoring
display unit
(MDU)
Filler panel
Maintenance
bypass switch
Document
holder

2
2
7. Insert expansion bolts into the expansion bolt
holes in the floor, and tighten the expansion
bolts.
2. Use a hammer drill to drill holes for installing
expansion bolts and then install four
expansion bolts in the holes. Remove the
bolts, spring washers, and flat washers.
3. Wheel the cabinet to the installation position.
4. If the castors of the UPS need to be lifted
from the ground, perform steps 1 to 2 in "Non-
Secured Installation."
5. Remove the rear cover from the cabinet and
open the front door.
6. Remove the four rubber plugs (two front and
two rear) from the bottom of the cabinet.
1. Lower the four leveling feet at the bottom of
the UPS using a wrench until all the four
castors at the bottom do not touch the floor
and the leveling feet bear the whole UPS
weight.
2. Check the UPS levelness using a level. If the
UPS is not level, adjust the leveling feet.
Non-Secured Installation
2.2
Secured Installation
2.1
1. Determine the cabinet installation position.
Mark mounting holes in the installation
position based on drawings.
Unit (mm)
2Installing the UPS

3
3Installing Cables
1. Open the front door, and remove the
front cover from the power distribution
subrack.
2. Remove the cable tray cover for the signal
cable, and remove a certain number of small
covers from the cabinet bottom based on site
requirements.
Installing UPS Cables
3.2
UPS Cable Connection Reference
3.1
•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may
ignite and cause personal injury or device damage.
•After cables have been installed, clean the cabinet in a timely manner. Ensure that there is no
foreign matter inside and around the cabinet.
•You need to prepare terminals onsite. The length of the stripped copper wire should be the
same as that of the part of the terminal that covers the conductor.
The cabling route is for reference only. Connect cables based on site requirements.
NOTE
The cover can be removed only when the maintenance bypass switch is OFF.
NOTE

4
4. (Skip this step if the mains and bypass
inputs share a power source.) Remove the
copper bars between the mains and
bypass input wiring terminals.
3. Connect the ground cables.
5. (If the mains and bypass inputs share a
power source, you do not need to connect
the bypass input power cable.) Connect the
mains and bypass input power cables.
6. Connect the output power cable.
•: internal equipotential connection label.
•: protection ground label.
NOTE

5
7. Connect the battery cable. 8. Connect the signal cable.
The number and color of signal cables in the figure are for reference only. Signal cables can be
routed along the left or right side of the cabinet. Route signal cables based on the actual situation.
4Verifying the Installation
1. Check that there is no foreign
matter in the cabinet.
2. After verifying the installation,
reinstall all the covers.
NOTE
Wiring terminal
blocks and switches
Cabinet top
Cabinet bottom
Rear of the
modules

Paper
protective film
Sealing putty
6
Dustproof
cover
5Powering On and Starting the UPS
Powering On the UPS
5.1
Turn on the external bypass and mains input switches.
After the UPS is powered on, initialization begins. The MDU
displays the Huawei logo and an initialization progress bar.
3. (Remove the paper protective film from the
sealing putty.) After routing cables and verifying
cable connections, seal the gap between
cables and the cabinet using sealing putty.
4. Do not remove the dustproof cover before
power-on to prevent dust from entering the
UPS.
Starting the Inverter
5.2
Battery
Specifications
Number of
Batteries
Connected
in Series
Number of Battery
Strings Connected in
Parallel to the UPS
Number of
Cells
Battery Capacity
150 Ah/12 V DC
36
2
36 x 6 = 216
150 Ah + 150 Ah = 300 Ah
300 Ah/2 V DC
192
2
192 x 1 = 192
300 Ah + 300 Ah = 600 Ah
300 Ah/12 V DC
40
3
40 x 6 = 240
300 Ah + 300 Ah + 300 Ah
= 900 Ah
300 Ah/2 V DC
240
4
240 x 1 = 240
300 Ah + 300 Ah + 300 Ah
+ 300 Ah = 1200 Ah
•Number of cells indicates the number of 2 V DC batteries in a battery string connected to the UPS.
•If multiple UPSs share battery strings, the battery capacity of each UPS is the total capacity of the
battery strings.
1. Before powering on the UPS, ensure that the UPS has passed all check items in the UPS5000
Commissioning and Acceptance Report and Chapter 4.
2. Measure the voltage and frequency of the mains and bypass inputs of the UPS, or the voltage
and frequency output from the external input power distribution cabinet (PDC) to the UPS.
Ensure that the line voltage is in the range of 138–485 V AC and the frequency is in the range
of 40–70 Hz.
Sealing putty must be used as a whole and
the gap can be sealed only from the top.

7
Initial Startup
a. During the initial startup, set the language, time and date, network parameters, and system
parameters on the Settings Wizard screen.
b. After you set parameters on the Settings Wizard screen, the MDU displays the Bypass mode
and No battery alarms, which do not need to be handled. If there is any other alarm, you need to
rectify the fault.
c. View the system running diagram on the MDU to check that the UPS is working in bypass mode.
d. Start the inverter on the app.
•The Service Expert app can be downloaded from Google Play and can run on Android.
•The port number is 443 by default and can be modified. If the UPS is managed using the app,
the port number must be set to 443.
NOTE

8
System User
LCD Preset Password
WebUI
Preset Password
admin (administrator)
000001
Changeme
operator (common user)
000001
Changeme
a. Choose Common Functions from the main menu and tap Inv. ON.
b. In the displayed login window, enter the user name and password, and tap .
c. In the displayed dialog box, tap OK to start the inverter.
Non-initial Startup
Download the mobile phone app
(Service Expert).
On the home screen of the app, tap Startup to
access the Set Startup screen. Select Site and
Device Type as required and connect to the
device. Enter UPS IP address and port
number (default value: 443), use the user
name and password of the WebUI account,
and tap Login.
Enable the mobile phone WLAN, search for the
UPS WiFi signal, and connect to the WiFi
signal. The default value of WiFi SSID is
HUAWEI_UPS.
Insert the WiFi module into the USB port on the
MDU. Choose System Info > Settings >
Communication, and set WiFi Password on
the MDU.
After login, tap Power-on password activation
on the screen. A message is displayed,
indicating whether to start the UPS. Tap OK.
On the Offline Activation screen, enter the
Bar code and Verification obtained from
the MDU. Tap Generate PWD to generate
a startup password.
On the MDU, choose System Info >
Maintenance > Inv. ON and obtain the Bar
code and Verification.
Enter the generated password in the
password text box on the MDU to start the
inverter.
Use the app to
start the inverter
online?
Yes
No, start the
inverter offline
Open the Service Expert app.
Open the Service Expert app.
On the home screen of the app, tap
Startup to access the Set Startup screen.
Select Site and Device Type as required,
and tap Offline Activation.
NOTE
To ensure system security, change the preset password after login.

9
(Optional) Setting Parameters for the BCB Box
5.4
1. If a BCB box is configured, set MUE05A connection to Enable in Settings > Dry contacts,
and then set BCB connection [OL] and Battery breaker [STA] to Enable.
Powering On Loads
5.3
1. After the inverter starts, the UPS works in normal mode. The Bypass mode alarm disappears
from the MDU.
2. After confirming that the battery strings are properly connected, turn on the battery string input
circuit breaker. If there are multiple battery strings, turn on the circuit breaker for each battery
string and then turn on the general circuit breaker between battery strings and the UPS. The No
battery alarm disappears from the MDU.
3. Turn on the UPS downstream output switch to supply power to the loads.
6Shutting Down the UPS
1. On the LCD, choose Common Functions, and tap Inv. OFF.
2. In the displayed login window, enter the user name and password, and tap .
3. In the displayed dialog box, tap OK to shut down the inverter.
Shutting Down the Inverter to Transfer the UPS to Bypass Mode
6.1
Powering Off a Single UPS
6.2
Turn off the external output power distribution switch and battery string switch.
Turn off the external mains and bypass input power distribution switches.
After you shut down the inverter, the UPS transfers to bypass mode if the bypass is normal; the
UPS supplies no power if the bypass is abnormal. Before shutting down the UPS, ensure that all
loads have been shut down.

10
Huawei Technologies Co., Ltd.
Huawei Industrial Base, Bantian, Longgang
Shenzhen 518129 People's Republic of China
www.huawei.com
Scan here for more documents:
You can also log in to Huawei technical support website:
http://support.huawei.com/enterprise
http://support.huawei.com
SupportSupport-E WeChat
Scan here for technical support (enterprise):
Scan here for technical support (carrier):
Huawei App Store
Huawei App Store