Huayu HY-500-Pro User manual

Huayu(Zhejiang)New Energy Technologies Co.,Ltd. All rights reserved.
c
QUICK INSTALLATION GUIDE
Installing a Huayu HY-500/600-Pro Microinverter
Meter
Distribution
Box
Microinverter
Ground
Neutral
PV
Module
WiFi Router Monitoring System
WiFi Booster
A PV system by Microinverters is simple to install. Each Microinverter easily mounts on the PV racking system, directly beneath the PV module. Low voltage DC
wires connect from the PV module directly to the Microinverter, eliminating the risk of high DC voltage. Installation MUST comply with local regulations and
technical rules.
Special Statement! An AC GFCI device should not be used to protect the dedicated circuit to the Microinverter even though it is an outside circuit. None of the
small GFCI devices(5~30mA) are designed for back feeding and will be damaged if so. In a similar manner, AC AFCIs have not been evaluated for back
feeding and may be damaged if back feed with the output of a PV inverter.
WARNING
Perform all electrical installations in accordance with local electrical codes.
Be aware that only qualified professionals should install and/or replace Microinverters.
Before installing or using a Microinverter, please read all instructions and warnings in the technical documents and on the Microinverter itself
as well as on the PV array.
Be aware that installation of this equipment includes the risk of electric shock.
Do not touch any live parts in the system, including the PV array, when the system has been connected to the electrical grid.
Strongly recommend to install surge protection devices in the dedicated combiner box.
Additional Installation Components
AC Male and Female Interconnection Connectors(offered separately)
Sealing end caps(offered separately)
Required Parts and Tools
In addition to your PV array and its associated hardware, the following
items are needed for installation:
An AC connection junction box
Mounting hardware suitable for module racking system
Sockets and wrenches for mounting hardware
Continuous grounding conductor and grounding washers
A Phillips screwdriver
A torque wrench
NOTE:
If the wireless signal in the area for the Microinverter is weak, it is necessary to add a WiFi signal booster at a suitable place between the router and the
microinverter.
This integrated system improves safety; maximizes solar energy harvest; increases system reliability and simplifies solar system design, installation,
maintenance and management.
Simple to Install
You can install individual PV modules in any combination of Module
quantity and orientation, different type and power rate. The Ground
wire (PE) of the AC cable is connected to the chassis inside of the
Microinverter, potentially eliminating the installation of grounding
wire(check local regulation).
Data collection adopts internal WiFi, wireless router is needed near
the Microinverter. When complete the installation of microinverter,
configure wireless router with internal WiFi(refer to the WiFi user
manual). The data will be uploaded automatically. Users can monitor
and manage the microinverter through corresponding website or APP.
1
2
1
2
3
4
5
6

INSTALLATION
Specifications subject to change without notice - please ensure you are using
the latest manual found at the manufacturer website: www.huayu-energy.com
When AC power is applied but Microinverter is not started up, about 0.1A
current and 25VA(W) power for each Microinverter may be measured by a
power meter, this power is reactive power, not from grid.
NOTE:
NOTE:
Step 5- Install an AC cable protective end cap at the end
of AC cable
7.5
NOTE:
When plugging in the DC cable, if AC is already available, the Microinverter
should immediately blink red light and will start working within the setting time
(default 60 seconds). If AC is not available, the red light will blink 3 times
quickly until AC is connected.
Step 6- Connect Microinverter to PV Modules
Huayu(Zhejiang)New Energy Technologies Co.,Ltd. All rights reserved.
c
Installation Procedure
Step 1- Install AC branch circuit junction box
Step 2- Attach Microinverters to racking system or
the PV module frame
Prior to installing any of Microinverters, verify that the utility voltage at
the point of common connection matches the voltage rating on
Microinverter label.
Do not place the Microinverter(including DC and AC connectors)
where exposed to the sun, rain or snow, even gap between modules.
Allow a minimum of 3/4 inch(2cm). between roof and bottom of the
Microinverter to allow proper air flow.
WARNING
Wiring colour code can be different according to local regulation,check
all the wires of the installation before connecting them to the AC cable.
Wrong cabling can damage irreparably Microinverters,such an issue is
not covered by the warranty.
WARNING
Mark the location of the Microinverter on the rack, with respect
to the PV module junction box or any other obstructions.
Mount one Microinverter at each of these locations by
recommended hardware.
1
2
1
2
3
Step 3- Create an Installation Map
Peel the removable serial number label from each microinverter and affix
it to the respective location on the paper installation map.
Fill in the monitoring system account information to the installation map
Create a paper installation map to record microinverter serial numbers and position
in the array.
Always keep a copy of the installation map for your records.
Affix serial number labels
DO NOT exceed maximum number of Microinverters in an AC branch
circuit.
WARNING
HY-500-Pro / HY-600-Pro(-127V)
L(L1) N(L2)
PE
Step 4- Connect the Microinverters in parallel
2Plug the male AC connector of Microinverter into the female connector to
get it connected. AC connector interface is as follows.
1Check Microinverter technical data for the maximum allowable number of
Microinverters on each AC branch circuit.
HY-500-Pro / HY-600-Pro(-127V)
connected in parallel
Install an appropriate junction box at a suitable location on the PV racking
system(typically at the end of a branch of modules).
Connect the open wire end of the AC cable into the junction box using an
appropriate gland or strain relief fitting.
Wire the conductors of the AC(127/220/230): L - red; N - black;
PE - yellow green. Wire the conductors of the AC(208/240): L1- red;
L2 - black; PE - yellow green.
Connect the AC branch circuit junction box to the point of utility
Interconnection.
1
2
3
4
A
12345678910
Customer:
1. Affix the serial number label to the respective location of the map.
2. Scan related QR Code of Microinverter and upload it to Huayu Monitoring platform.
Panel Group:
Azimuth:
Tilt:
Sheet____of____
Monitoring System Account:
Installer:
B
C
D
E
F
G
H
J
K
L
W E
N
S
N
119088

A
12345678910
Customer:
1. Affix the serial number label to the respective location of the map. 2. Scan related QR Code of Microinverter and upload it to Huayu Monitoring platform.
Panel Group: Azimuth: Tilt: Sheet____of____
Monitoring System Account:
Installer:
B
C D
E
F
G
H
J
K
L
W E
N S
N