HUBBELL LIGHTING DUAL LITE PGF1 LED Wallpack Manual

Hubbell Lighting, Inc.
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
or otherwise touching this product.
SERVICE
Hubbell Lighting, Inc. Life Safety Prducts • www.dual-lite.com
Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specications subject to change without notice. • Printed in U.S.A.
93036067 11/11
High Performance LED Wallpack For Indoor
Or Outdoor Application
Installation, Operation and Service Instructions
PGF1 LED Wallpack
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Do not let power supply cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
INSTALLER:
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
93021413
93021935
93021938
93021939
93036084
93036085
93036096
LED Replacement
Contact factory
PATENTS
PENDING
RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts
are recyclable.
All cartons contain recycled materials.
Please recycle responsibly.

Screw
O-Ring
Backplate
Cover
INSTALLATION OPERATION
120VAC Connect black (hot) and neutral (white)
to supply.
277VAC Connect black (hot) and neutral (white)
to supply.
Ground Connect ground (green) conductor.
IMPORTANT:
Once unit is connected and cover is snapped onto backplate, gently seat screws onto
O-ring seals to less than 1/2FT-LB (.7N-m).
DO NOT OVERTIGHTEN!
O-RING MAY BE DAMAGED AND THE UNIT WILL LEAK IF ABOVE IS NOT
FOLLOWED.
1.Open the unit by loosening both screws on top of unit until screws spin freely. Pry cover
from backplate, and remove cover squarely from backplate. (Remove screws prior to
re-installing cover.)
2.Remove 7/8” diameter K.O. from backplate if mounting to electrical
box or remove 1/2”-1/4NPT pipe plug if using conduit.
CONDUIT MOUNTING:
If unit is not secured to mounting surface using unit backplate
K.O. pattern and supplied gasket, use sealant to create
waterproof seal between the mounting surface and the unit
backplate.
IMPORTANT!
To weatherproof your outdoor installation, be sure to seal all
fixture openings - mounting, conduit, etc.
4.Peel backing from J-Box Gasket and adhere to
backplate around center K.O.
5.Feed building wires through center K.O. as
shown and secure backplate using screws
supplied with electrical box.
3.Remove appropriate backplate K.O.’s
for electrical box screws.
7.Connect AC wire harness to AC wire harness
on unit backplate.
AC Wire Harness
To Building Ground Wire
NOTE:
Feed wires and nuts back into electrical box through
backplate as shown.
9.Attach unit cover to backplate by
reversing Step 1. Ensure all wires
are within enclosure to avoid pinching
with cover.
Full Cut-off Shield Installation Photo-Cell Option
1.Slide tabs “A” between housing and lens gasket.
2.Pinch sides of shield inward and seat shield against lens.
3.Release pinched sides of shield to secure to unit.
There will be a delay of up to 2 minutes to prevent false switching due to
momentary flashes of light.
TABS “A”
Pinch sides inward
Unit will operate from 120 or 277VAC through 2 wire intelligent input.
Photo-cell option: Unit will operate on 120VAC only, through 2 wire input.
93021938
93021935
93036085
93036084
9303609693021939
6.Connect building AC wires to
AC harness wires.