Hubbell Dual-Lite PGR LED Sconce Manual

Hubbell Lighting, Inc.
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
or otherwise touching this product.
SERVICE
Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com
Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A.
93036103 B 5/2011
High Performance LED Sconce
For Indoor or Outdoor Application
Installation, Operation and Service Instructions
PGR LED Sconce
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. Do not let power supply cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
INSTALLER:
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
93021413
93021935
93036104
93036105
93021938
93021939
LED Replacement
Contact factory
RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts
are recyclable.
All cartons contain recycled materials.
Please recycle responsibly.
93021413
US Patent No. D627,916

Screw
O-Ring
Backplate
Cover
INSTALLATION OPERATION
Ground Connect ground (green) conductor.
6VDC
through
12VDC
CAUTION: OBSERVE POLARITY
Connect blue (+) conductor to building
(+) DC supply. Connect yellow (-)
conductor to building (-) DC supply
IMPORTANT:
Once unit is connected and cover is snapped onto backplate, gently seat screws onto
O-ring seals to less than 1/2FT-LB (.7N-m).
DO NOT OVERTIGHTEN!
O-RING MAY BE DAMAGED AND THE UNIT WILL LEAK IF ABOVE IS NOT
FOLLOWED.
1.Open the unit by loosening both screws on top of unit until screws spin freely. Pry cover
from backplate, and remove cover squarely from backplate. (Remove screws prior to
re-installing cover.)
2.Remove 7/8” diameter K.O. from backplate if mounting to electrical
box or remove 1/2”-1/4NPT pipe plug if using conduit.
CONDUIT MOUNTING:
If unit is not secured to mounting surface using unit backplate
K.O. pattern and supplied gasket, use sealant to create
waterproof seal between the mounting surface and the unit
backplate.
IMPORTANT!
To weatherproof your outdoor installation, be sure to seal all
fixture openings - mounting, conduit, etc.
4.Peel backing from J-Box Gasket and adhere to
backplate around center K.O.
5.Feed building wires through center K.O. as
shown and secure backplate using screws
supplied with electrical box.
3.Remove appropriate backplate K.O.’s
for electrical box screws.
6. Connect DC supply wires to
DC harness wires
7.Connect DC wire harness from unit backplate
to J1 on power supply PCB.
DC Wire Harness To Building Ground Wire
NOTE:
Feed wires and nuts back into electrical box through
backplate as shown.
8.Attach unit cover to backplate
by reversing Step 1. Ensure all
wires are within enclosure to avoid
pinching with cover.
Unit will operate from 6 through 12VDC.
93021938
93021935
93036104
93036105
Full Cut-off Shield Installation
1.Slide tabs “A” between housing and lens gasket.
2.Pinch sides of shield inward and seat shield against lens.
3.Release pinched sides of shield to secure to unit.
TABS “A”
Pinch sides inward
93021939