Human Touch Perfect Chair Zero-G PC-050 User manual

©2010 Human Touch®, LLC. Patents pending and intellectual property rights enforced.
No medical claims are warranted or implied by the use of this product.
Human Touch is a trademark of Human Touch®, LLC.
PC-050-NA-A0
humantouch.com
800.355.2762
use & care manual
pc050
perfect chair®
Zero-G™
Model # PC-050

humantouch.com
You have just purchased one of the finest pieces of ergonomic furniture available.
The Human Touch® Perfect Chair® artfully blends the best of aesthetics,
technology and wellness in a seating experience that transcends the highest
standards of comfort.
The recline system eases the body into a virtually weightless position, as it
elevates the legs above the heart and relieves weight from the spine. This
remarkable chair relieves the soreness, tension and fatigue caused by the
earth’s constant pulling, while its fixed-form seating position ensures maximum
ergonomic posture at all recline angles.
To ensure that you don’t overlook any of your chair’s features, and that you use it
safely, read this manual carefully. Then sit back, relax, and enjoy!
welcome to human touch®
humantouch.com
Please send any questions or comments regarding this manual to [email protected]
keep it safe
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
• Do not sit on the chair arms.
• The chair is intended for stationary use, not for rocking.
• Always recline slowly to maintain optimal control of the suspension system.
• Keep fingers and loose clothing away from the guide rails at all times.
• This product is not designed for use by disabled people or children without adult supervision.
• If you have chronic back pain, have undergone back surgery, or have any questions about using this product,
consult your physician before use.
• If you experience dizziness or nausea, discontinue use and contact your physician immediately.
Do not attempt to repair this product yourself.
• This product is designed for personal in-home use. Commercial use will void warranty.
When using this product, basic precautions should always be followed, including
the following:
perfect chair®
Zero-G™

humantouch.com 23
get ready
Your Human Touch Perfect Chair requires some simple assembly. Just attach the
headrest/footrest frames, pads, arm caps, and head pillow, and you’re done!
3
UNPACK THE BOXES
Chair frame
Headrest frame
Slide the two ends of the footrest frame into the tube openings
in the front of the chair frame.
1. Slide the footrest frame onto the chair frame.
Using the Allen wrench and two of the provided screws,
secure each side of the footrest frame to the chair frame.
2. Install the footrest frame screws.
Using both hands, continue to pull the seat canvas all the way
forward to tightly cover the footrest frame, then secure the two
front and two side flaps, using the hook and loop fasteners.
4. Finish securing the canvas to the frame.
Footrest frame
Using both hands, pull the seat canvas forward just to the
top of the footrest frame, then secure the two flaps located
underneath the canvas to the footrest frame.
3. Attach the canvas to the footrest frame.
Arm cap (2) Head pillow
Head pad
Slide the body pad onto the lower part of the chair frame,
making sure that the frame slides into the fabric pocket located
on the bottom side of the pad.
Smooth the body pad into place, from the footrest toward
the backrest, making sure the top flap is flipped forward,
onto the body pad. The pad is automatically secured using
the hook and loop fasteners.
ATTACH THE BODY PAD
1. Slide the body pad onto the chair frame.
2. Secure the body pad.
TO AVOID DAMAGE TO THE CHAIR OR
PERSONAL INJURY, DO NOT SIT IN
CHAIR UNTIL ASSEMBLY IS COMPLETE.
Body pad
Bag contains:
Allen wrench (1),
Allen screws (12),
rubber washers (2),
flat washers (2),
hinge pin (1), clevis clip (1)

4 5
get ready ATTACH THE ARM CAPS
1. Hook the bracket inside the front end of the arm cap into the
catch in the top of the arm frame. Lower the arm cap into position
on top of the arm frame and seat firmly with edges aligned.
2. Using the Allen wrench (provided), insert four of the provided
Allen screws into the screw holes on the underside of the armrest
and tighten them to secure the arm cap to the chair.
3. Repeat steps 1 and 2 to secure the other armrest cap to the chair.
1. Raise the chair to an upright position.
ATTACH THE HEADREST FRAME
For your convenience, and to better position the chair for the remaining assembly, use the recline lever to adjust
the chair to an upright position.
Using the provided Allen wrench and two provided screws,
secure the headrest frame to the backrest frame.
2. Insert the headrest frame into the backrest frame.
3. Install the headrest frame screws.
With the headrest frame positioned so that it can tilt forward, slide the two ends
of the headrest frame into the open tube ends at the top of the backrest frame.
1. Locate the hook-and-loop fastener that secures the brake to the
bottom of the seat canvas.
2. Open the hook-and-loop fastener to free the brake from the canvas.
3. Remove the disposable protective brake cover and discard it.
IMPORTANT: The brake shaft is lubricated. Hold the shaft at the end
to avoid handling the lubricant.
4. Tilt the chair frame forward until the end of the brake shaft is aligned
with the mounting bracket.
5. Insert the hinge pin through one of the provided flat washers,
through the mounting bracket hole, through one of the rubber
washers, through the brake shaft, through the second rubber washer,
through the other mounting bracket hole, then through the second
flat washer.
6. Install the clevis clip on the end of the hinge pin to secure it.
Brake shaft
ATTACH THE BRAKE
TO AVOID DAMAGE TO THE CHAIR OR
PERSONAL INJURY, DO NOT SIT IN
CHAIR UNTIL ASSEMBLY IS COMPLETE.
Clevis clip
Hinge pin
Flat washer
Brake shaft
Mounting
bracket
Mounting
bracket
Washer

humantouch.com 67
get ready
Slide the headrest cover the rest of the way down over
the headrest frame, as far as it will go.
ATTACH THE HEAD PAD
1. Finish installing the headrest cover.
Slide the head pad over the head frame, ensuring that the frame
slides into the fabric pocket located on the bottom side of the
pad. Pull the head pad down as far as it will go.
2. Slide the head pad over the head frame.
From the front of the chair, tuck the flap on the top of the body pad
up into the head pad and smooth it flat. The flap is automatically
secured to the pad, using the hook and loop fasteners.
3. Tuck in the body pad flap.
Attach the head pillow straps to the head pad straps using
the hook and loop fasteners. Adjust the head pillow height for
maximum comfort.
4. Attach the head pillow.

humantouch.com 89
take a seat
Using your Human Touch Perfect Chair is easy. Just take a seat and
adjust the chair to the desired position. The Perfect Chair cradles you
in zero-gravity comfort, with your feet above your heart—the ultimate
neutral-posture position for back and spine relief.
To recline, gently pull up on the recline lever, lean back on the backrest to adjust it to the desired angle, then
release the lever. To incline to a more upright position, gently pull up on the recline lever, then pull up on
the armrests with your hands while applying slight downward pressure with your elbows, until the backrest
inclines to the desired position. Release the recline lever.
Adjust the headrest
While seated, reach up with both hands and grasp both sides of
the headrest. You will feel the rigid frame beneath the soft head
pad. Grasping the rigid frame, tilt the headrest forward or back-
ward for maximum comfort. The headrest remains in this position
until you adjust it again.
Adjust the recline angle
Getting out of the perfect chair
Gently pull up on the recline lever, pull up on the armrests with
your hands while applying slight downward pressure with your
elbows, until the backrest inclines to a full upright position.
Release the recline lever. Use the arms for support when getting
up from the chair.
NOTE: Lean back against the backrest before reclining the chair.

humantouch.com 10 11
To keep your product working and looking its best, please follow
these simple care guidelines.
care and maintenance
Cleaning:
1. Do not use benzene, thinner or any other solvents on your chair.
2. Remove dust on the backrest or armrest with a vacuum.
3. If the backrest or armrests become soiled, wipe with a damp cloth, then a dry cloth.
4. Common upholstery cleaners may be used for tough stains.
Fabric Care:
To maintain your Human Touch product in optimum condition, dust it frequently and/or vacuum it with a soft brush vacuum
extension. SofSuede® products can also be brushed with a suede brush. Wipe with a slightly damp cloth as necessary. For
tougher stains on non-leather products, use a mild detergent mixed with water. Leather products should be wiped down
occasionally with a leather furniture cleaning solution.
WARNING:
Be sure to test any cleaning solution on a small, inconspicuous part of the product to ensure that the color does not fade prior
to using the solution on the entire product surface.
Maintenance and Repair:
1. The mechanics of this product are specially designed and constructed to be maintenance free. No periodic lubrication
or servicing is required.
2. Your chair should only be serviced by an authorized service center.
Use and Storage Environment:
1. When not in use for a long period of time, we recommend that the chair be covered and that the unit be placed in an
environment free of dust and moisture.
2. Do not store near heat or open flame.
3. Do not leave this product exposed to direct sunlight for long periods of time. This may cause fading or damage.
4. Product should be used and stored in an environment with non-condensing humidity ranging from 10 to 80%;
excessive humidity will damage the mechanics.
Miscellaneous:
1. Foreign objects should not be inserted in the recline suspension wheels or other moving parts.
2. Care should be taken not to overload the unit.

12 13
Chair Size (upright): 43” L x 30” W x 45” H
Chair Size (reclined): 57” L x 30” W x 29” H
Product weight: 71 Lbs.
Required recline clearance: 12”
Maximum load weight: 285 Lbs.
*Specifications are subject to change without prior notice.
Specifications*
Model # PC-050