Hunter HPH625 User manual

Air Purier & Humidier
Models:
HPH625
(All Colors)
Form #HPH625
08102023
© 2023 Produced exclusively for Mindful LLC under license by Hunter Fan Company
All rights reserved
English
READ AND SAVE THESE INSTRUCTIONS

Table of Contents
Safety Instructions ..................................... 1-3
Initial Setup ................................................. 4
Operation .................................................... 5
Control Panel .............................................. 6
Display Screen ............................................ 7
Remote Control .......................................... 8-9
Maintenance .............................................. 10-12
Troubleshooting ........................................ 13
Customer Support ..................................... 14
Limited Warranty ....................................... 15-17

1
Safety Instructions
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and
on y our appliance. A lways read a nd obey all safety messages.
This is the safety alert symbol. This symbol alerts you to
potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol
and either the word “DANGER” or “WARNING.” These
words mean:
All safety messages will tell you what the potential hazard is, tell you how
to r educe the c hance of i njury, a nd t ell you what can happen i f the
instructions are not followed.
DANGER
WARNING
This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit into a polarized
outlet only one way. If the plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not attempt to
defeat this safety feature.
Do not operate appliance with a
damaged cord or plug. Discard product
or return to an authorized service facility for examination or repair.
Unplug appliance before servicing.
Do n ot r un c ord under c arpeting. D o not cover cord with t hrow r ugs,
runners, or similar covering. Do not route cord under furniture, or appliances.
Arrange cord away from traffic area and where it will be tripped over.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WARNING: To reduce the risk of fire or electrical shock, DO NOT use the
appliance with any Solid-State Speed Control Device.
WARNING: To r educe the risk o f fire o r electrical shock a nd i njury to
persons, DO NOT use in a window.
You can be killed or seriously
injured if you don’t
immediately follow instructions

2
Safety Instructions
Thank you for choosing the Hunter®Air Purier & Humidier! Please read and save these
instructions to receive the maximum benet and performance from your unit.
READ AND SAVE THESE INSTRUCTIONS!
Important Safety Instructions:
Read all instructions before using this humidier
• This product may not work properly on an uneven surface. ALWAYS place this product on a
rm, level, and water resistant surface.
• ALWAYS place the product at least six (6) inches away from walls, heat sources, and
electrical appliances such as stoves, radiators, or heaters.
• ALWAYS place the product in an area that is out of the reach of children.
• Before using the product, extend the cord and inspect for any signs of
damage. DO NOT use the product if the cord has been damaged.
• Do not use the product outdoors or in locations subject to rain, water, heat, re or sun.
• Never wrap a power cord around product or other object. Doing so can stress the cord in
ways that can cause the cord to fray, crack, or crimp. This can present a safety hazard.
• Protect power cord from liquids. Do not leave power cord near sinks, tubs, toilets, or on
oors that are cleaned with liquid cleaners. Liquids can cause a short circuit.
• Ensure that all power cord connectors are securely and completely plugged into receptacles.
• Do not use product if power cord shows corrosion or signs of overheating.
• To prevent possible overheating, do not cover the power cord with clothing or other objects
when the power cord is plugged into an electrical outlet.
• ALWAYS UNPLUG AND EMPTY the product when it is not in operation or while it is being
cleaned.
• Use only clean, cool tap water when lling the tank. DO NOT use hot water.
• Never add medication of any type to the water tank.
• You should never leave the unit unattended in a closed room. The room can become
saturated and leave condensation on walls and furniture. Always leave a door partially open.
• This device complies with part 18 of the FCC Rules.
• To reduce risk of re, electric shock, or injury, place the unit and cord where it is not likely to
be tipped or bumped.
• Do not overll the water tank due to potential risk of electric shock.
• ALWAYS disconnect the product from power source before performing any maintenance or
cleaning.

3
Safety Instructions
• Keep away from children under the age of 8 unless supervised by an adult.
• For indoor use only.
• NEVER drop or insert any object into any openings.
• DO NOT run cord under carpeting, throw rugs or runners.
• DO NOT route cord under furniture or appliances. Arrange cord away from trac area and
where it will not be tripped over.
• NEVER block the air openings, grills/outlets.
• NEVER place the product on a soft surface, such as a bed or sofa, as this could cause the unit
to tip over, blocking the air intake or outtake opening.
• DO NOT place anything on top of the unit.
• DO NOT expose eyes or other body parts directly to UVC light, as UVC light can be harmful
to skin.
• UVC light should not be used on plants or animals, as it can cause harm.
• The UVC light is inside this product, you will not come into contact with it. The light on the
top of the product is the accent light.
• DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit, doing
so will void your warranty.

4
Initial Setup
1. Remove the product from packaging and place on a sturdy, at surface.
2. Unravel and straighten the cord before use.
3. Remove the top cover from the unit.
4. Add fresh, clean tap water to tank. Do not overll. Figure 1
5. Reattach top cover.
WARNING: Never ll water tank with hot water.
Figure 1

5
Power On: Follow the initial setup instructions. Plug product into wall outlet. On
product, press power switch to ON. Product will beep and light up as indication
that it is working. Current humidity will automatically display.
Power O: Press power switch to OFF. Empty water tank.
Rell Water Tank: See initial setup for instructions on relling water tank. DO NOT
overll. If tank is empty, product will still run as an air purier. Rell the tank to use
the humidier function. When tank is empty a water drop will ash 10 times on
the display screen before turning red. This will disappear once the tank is relled.
Figure 2
Operation
Figure 2
HEPA Filter: Helps purify your air.
Recommended to replace every 6
months. See Filter Replacement for
further instructions .
Permawick®: Helps purify your water.
Recommended to clean or replace as
needed due to environmental
reasons. See PermaWick® Cleaning for
further instructions.
Control Panel: How you operate your
machine. See Control Panel for further
instructions.
Handle: Always carry your unit by the
handle.

6
On/ O: Press button to power unit on or o.
Speed/ Sleep: By default, the machine will start running on low speed. Press the
button once to run on medium speed, twice for high speed and a third time for
sleep mode. Figure 4. The display screen will dim and the Sleep icon will appear.
Press button again to turn o sleep mode and return to low speed.
UV Mode: The UV mode will automatically turn on when you power on your unit.
Press the UV mode button once to turn it o. Press it again to turn it on. When UV
mode is on, the icon will appear on the display screen. Figure 4. When UV mode is
running the blue accent light will be on. This accent light is NOT the UV light, and
is safe to look at.
Timer: Press button to set timer. Timer will then increase by one hour each time
button is pressed, up to 12 hours. Press through all options to clear timer. Once
desired time displays, the number will ash ve times on the display screen to
signal timer is set. The Timer icon will appear on the display screen when a timer is
set. Figure 4. Unit will automatically shut o after the set time runs out.
Control Panel
Figure 3

7
Auto: Press button to have the unit run in Auto mode. The unit’s running speed
will be based on the room’s humidity. Humidity below 40% will light up RED on
the display screen and the unit will run on high speed. Humidity between 41-69%
will light up GREEN on the display screen and the unit will run on medium speed.
Humidity above 70% will light up ORANGE on the display screen and the unit will
run on low speed. Figure 4. The product will try to get the room’s humidity
between 41-69% and adjust its speeds accordingly. Press Auto button again to
turn o Auto mode. The Auto icon will appear on the display screen when Auto
mode is on. Your room’s current humidity level will appear on the display screen.
Filter Indicator: This icon will appear on the display screen when it is time to
change your HEPA lter. Figure 4. It is recommended to replace the HEPA lter
every 6 months, based on continuous use. However, depending on air quality
and environmental factors, the lter may need to be replaced more frequently.
After the lter is replaced, press and hold the lter indicator button to reset it. The
unit will beep 3 times to indicate reset, and the icon will disappear o the display
screen.
Display Screen
Figure 4
Orange
Green
Red

8
Using the Remote:
Your remote comes with a battery installed and does not need to be programmed.
Before using your remote for the rst time, you must take out the pull tab. To use
remote, make sure to point it at the front of the unit. The remote will not work
when pointed to the backside of the unit.
Remote Control
Figure 5
On/ O: Press button to power product on or o.
Auto: Press once to turn on Auto mode. Press again to turn
o Auto function.
Speed: There are three speed settings to choose from: low,
medium and high. Press the + to increase the speed
setting. Press the - to decrease the speed setting.
Timer: Timer can be set between 1 - 12 hours. Press the +
to increase the timer by 1 hour each time button is pressed.
Press the - to decrease the timer by 1 hour each time
button is pressed. Once desired timer displays, the timer
will blink ve times to signal timer is set.
UV Mode: The UV mode will automatically turn on when
you power on your unit. Press the UV mode button once
to turn it o. Press it again to turn it on. The accent light on
the top of the unit is NOT the UV light, but it will turn on
when the UV light is in use.
Sleep Mode: Press once to turn o the display lights and
run on the low settings. Press again to turn o sleep mode.

9
Remote Control
Replacing the Remote Control Battery:
It is recommended to replace the battery when the
product takes a long time to respond or stops responding
when the buttons are pressed.
1. Turn over remote control. Press the tab toward the right
and pull.
2. Pull out battery holder and replace the battery. Only
use the specied battery type (Lithium Button Cell
Battery CR2025). The battery must be installed with the
positive side facing up.
3. Insert battery holder back into remote.
Note: Do not apply excessive force to battery holder.
Remove battery when not using for an extended period
of time. When disposing of used battery, please use the
correct method of disposal.
Remote Replacement:
It is recommended to store your remote on the
designated spot on the top backside of the unit
that reads“Remote Placement”. Figure 7
Figure 6
Figure 7
Battery : Lithium Button Cell Battery (CR2025)
WARNING
Keep the lithium battery out of
reach of small children.
Small children may accidentally swallow it.
If swallowed, call your doctor immediately.
Battery : Lithium Button Cell Battery (CR2025)
WARNING
Keep the lithium battery out of
reach of small children.
Small children may accidentally swallow it.
If swallowed, call your doctor immediately.

Maintenance
Note: ALWAYS unplug the unit from electrical outlet before cleaning. NEVER allow
water to sit in water tank when not in use.
Hard water can cause calcium and magnesium to build up in a white powder on
base of unit, transducer, and inner surface of water tank. Over time, this can cause
humidier to stop working properly.
It is recommended to clean the water tank daily, and clean the PermaWick ®
every 1-3 months, depending on water hardness.
Humidier should be emptied and cleaned before storage.
Use a dry, soft cloth to dry unit after each cleaning.
Daily Maintenance:
It is recommended to rell the water tank with water every day to avoid odor from
sitting water and hard water build up.
1. Turn o unit and unplug from wall outlet.
2. Remove top cover.
3. Grab handle and lift water tank out of the unit. Drain any water into a sink or
tub. Shake water tank gently to remove any remaining water.
4. Rinse water tank thoroughly with water, empty, and wipe with a dry, soft cloth.
5. Wipe product base with a dry cloth if necessary.
6. Rell water tank as directed under Initial Setup and resume use.
Cleaning the Unit:
Hard water can cause calcium and magnesium to build up on base of unit in the
form of white powder. Clean as often as needed.
1. Wipe o surface and base of unit. For best results, use a microber cloth.
2. Rinse surface and base with clean water.
10

Maintenance
Filter Maintenance:
We recommend periodically checking and replacing lters for optimal
performance. Under normal conditions of continuous use the pre-lter should be
replaced every 3 months (approximately 2,160 hours) and the HEPA lter should
be replaced every 6 months (approximately 4,320 hours). This estimate is only a
guide. Depending on air quality and environmental factors, lters may need to be
replaced more regularly.
IMPORTANT: DO NOT use water, any liquid or detergents to clean the lters.
Filter Replacement:
1. Power o and unplug the product.
2. Gently take o back grille.
3. Grab the tab to remove the lter from the compartment.
4. Remove the pre-lter from the HEPA lter.
5. Align the pre-lter with the HEPA lter and rmly press to attach.
6. Put the lter back in the compartment.
7. Put the grille back into place and dispose of dirty lter.
Pre-Filter
Grille
True HEPA Filter
Figure 8
11

Maintenance
PermaWick® Cleaning:
We recommend periodically checking and cleaning the PermaWick® for
optimal performance. Under normal water conditions of continuous use the
PermaWick® should be cleaned every 1-3 months. This estimate is only a guide.
Depending on your water quality and environmental factors, the PermaWick® may
need to be cleaned more regularly.
IMPORTANT: DO NOT use water, any liquid or detergents to clean the PermaWick®.
Cleaning the PermaWick®:
1. Power o and unplug the product, ensure water tank is empty.
2. Remove the top cover from the unit.
3. Grab the handle inside the tank to remove the tank. Sit it on a sturdy surface.
4. Remove the Permawick® from the tank. WARNING: The PermaWick® may be
saturated with water and drip when removed.
5. Rinse the PermaWick® with water and vinegar.
6. Allow the PermaWick® to air dry before placing it back inside the tank.
7. Lift the tank by the handle to place back inside the unit.
8. Place top cover on the unit and resume use.
Tank Handle Top Cover
PermaWick®
12
Figure 9

Troubleshooting
13
Problem: Excessive Noise
Solution:
1. The water tank is not attached correctly. Properly secure water tank to base of
unit.
2. The product is on an unstable surface. Place unit on a sturdy, at
surface.
3. The water tank does not have enough water. Fill water tank with water. See
Initial Setup.
Problem: Product is not working properly
Solution:
1. The unit is not connected to power. Plug unit into a wall outlet and press the
power button.
2. The water tank does not have enough water. Fill water tank with water. See
Initial Setup.
3. The water tank has too much water. Remove excess water from tank.
4. Filter may be excessively dirty. Replace lter as needed.
Problem: Abnormal mist smell
Solution:
1. The unit is new. Remove tank cover and let water tank air out for 12 hours in a
dry, cool space.
2. The water is dirty or has been sitting in unit too long. Clean water tank and add
fresh, clean water. See instructions in Maintenance.
Problem: No mist coming from humidier
Solution:
1. This unit uses an evaporative humidier. Evaportative humidiers evaporate
water inside and use a fan to push water vapor out into the air that is not
commonly visible.

Customer Support
14
Technical Support
If you need any assistance with setup, operation, or parts for your new Hunter
Air Purier/ Humidier, please call us. Our technical support sta is ready to help!
USA/Canada: 855-887-1440
Email: [e-mail]
Hours of operation are from 8:00 AM to 6:00 PM ET, Monday through Friday. You
may also contact us online at www.hunterpureair.com.
For all of the latest updates and promotions, follow us on our social media
channels:
@hunterpureair
@hunter_pureair
Replacement Parts Ordering:
Replacement lters and wicks may be ordered online at www.hunterpureair.com
or by phone by calling Hunter® Customer Support at [phone]. Applicable
state and local taxes may apply. Prices are subject to change without notice.
Model # Part # Description
HPH625 H-PF625 Pre-Filter, 2 Pack
HPH625 H-HF625 True HEPA Photocatalyst
Filter
HPH625 H-SW625 PermaWick®

Limited Warranty
15
Mindful, LLC makes the following limited warranty to the original residential user
or consumer purchaser of the Air Purier/ Humidier: If any part of the Air Puri-
er/ Humidier fails during two (2) years from the date of purchase due to a defect
in material or workmanship, we will provide a replacement part free of charge. If
no replacement part can be provided, we will replace your product.
IF THE ORIGINAL RESIDENTIAL USER OR CONSUMER PURCHASER CEASES TO OWN
THE AIR PURIFIER/ HUMIDIFIER, THIS WARRANTY AND ANY IMPLIED WARRANTY
WHICH THEN REMAINS IN EFFECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS
WARRANTY SET FORTH ABOVE.
This warranty is voided if your Air Purier/ Humidier is not purchased and used
in the USA or Canada.
This warranty excludes and does not cover defects, malfunctions, or failures of the
product which were caused by repairs by persons not authorized by us, use of
parts, or accessories not authorized by us, mishandling, possession, or
unreasonable use, including failure to provide reasonable and necessary
maintenance. This warranty does not cover products used in commercial
applications. There are no express or implied warranties as to commercial
purchasers or users.
See next page for more information on what is not covered.

Limited Warranty
16
What is not covered:
• Units that are sold“as is”, are used, or sold by unauthorized resellers
(an unauthorized reseller is dened as any third-party reseller who has no ocial
relationship with Mindful LLC.)
• Shipping or freight charges to return products for warranty service.
• Commercial or non-residential use or use inconsistent with the product
instructions and manuals.
• Consumable parts (e.g., light bulbs, batteries, lters, etc.)
• Defects or damage resulting from accident, misuse, abuse, alteration, re, oods,
or acts of God.
• Cosmetic damage (e.g., scratches, dents, chips, and other damage to nishes),
unless such damage results from defects in materials and workmanship and is
reported within 30 days from date of delivery.
• Units with original, factory installed model numbers removed, altered, or not
easily determined.
• Damage resulting from improper packing of products returned for warranty
service.
• Replacement parts, repair labor costs and/or replacement of a “failed” air
purier/ humidier operated outside the United States and Canada.
• Mindful LLC will have the nal determination regarding who an unauthorized
reseller is determined to be.

Limited Warranty
17
To obtain service, contact Hunter® Pure Air Customer Service at 855-887-1440. You
will be responsible for insurance and freight or other transportation to our factory
service center. We will return the freight prepaid. The Air Purier/
Humidier should be properly packaged to avoid damage in transit since we
will not be responsible for any such damage. Proof of purchase is required when
requesting warranty service. The purchaser must present sales receipt or other
document that establishes proof of purchase.
IN NO EVENT SHALL HUNTER PURE AIR BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE AIR PURIFIER/ HUMIDIFIER. YOUR SOLE REMEDY WILL
BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE. SOME AMERICAN STATES AND
CANADIAN PROVINCES DO NOT ALLOW:
• LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS;
• THE EXCLUSION OR LIMITATION OF DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES; THE EXCLUSION OR INVALIDITY OF EXPRESS OR
IMPLIED WARRANTIES IF THE USER CEASES TO OWN THE AIR PURIFIER/
HUMIDIFIER;
• THE LIMITATION OF THE REMEDIES AND RECOURSES AVAILABLE TO THE
PURCHASER; OR THE INVALIDITY OF AN EXPRESS WARRANTY WHEN A PRODUCT
IDENTIFIED BY BRAND NAME IS NOT USED (UNLESS SPECIFIC CONDITIONS ARE
FULFILLED); SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO
PROVINCE.
To request warranty service, visit www.hunterpureair.com
or call [phone]