FIRMWARE UPDATES
If new rmware versions are released for any of these components, the les can be downloaded from the
Hunter website and uploaded to the EZ-DT via microSD card within the battery compartment (microSD card
not included).
To update the rmware of an ICC2 facepack or an EZ-DM decoder output module, use the ribbon cable
connector located under the top cover.
EZ-1 decoders can be updated via red and blue wired connection.
ICC2 Facepack
1. From the Home screen, select Update -> Select ICC2 -> Remove the ribbon cable from the ICC2 power module and insert it
into the EZ-DT (as shown in the display) -> Then press Enter.
2. Successful updating of the facepack is conrmed with two beeps and a green check mark.
EZ-DM
1. From the Home screen, select Update -> Select EZ-DM -> Remove the ribbon cable from the ICC2 facepack and insert into
EZ-DT (as shown in the display) -> Then press Enter.
2. Successful updating of the EZ-DM is conrmed with two beeps and a green check mark.
EZ-1
1. From the Home screen, select Update -> Select EZ-1 -> Insert red and blue wires from decoder into EZ-DT programming port*
-> Then press Enter. *Multiple decoders can be updated at once with the two-wire path.
2. Successful updating of the decoder is conrmed with two beeps and a green check mark.
ADDITIONAL SETTINGS
The EZ-DT display is available with 12 language options.
1. From the Home screen, select Settings -> Select Language -> Choose the desired language -> Then
press Enter
The EZ-DT device can be updated aer purchase. If a new EZ-DT rmware version is available, it can be
downloaded from the Hunter website, and uploaded to the EZ-DT via microSD card within the battery
compartment (microSD card not included).
1. From the Home screen, select Settings -> Then select Update -> Then choose Yes or No.
2. Successful updating of the EZ-DT is conrmed with two beeps and a green check mark.
OPERATING SPECIFICATIONS
• Power input: 4 x AAA batteries
• Communications: wireless induction,
1" (25 mm) range from EZ-1 decoder to EZ-DT
DECLARATION OF CONFORMITY TO EUROPEAN DIRECTIVES
Hunter Industries declares that the model EZ-DT complies with the standards of the European Directives of
“electromagnetic compatibility” 2014/30/EU. Full text of the EU Declaration of Conformity is available at the following
internet address: https://hunter.info/compliance.
FCC NOTICE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, you are encouraged to try to correct the interference by taking one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that of which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by Hunter Industries could void the user’s authority to operate this
device. If necessary, consult a representative of Hunter Industries Inc. or an experienced radio/television technician for
additional suggestions.
ISED CANADA NOTICE
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage, et
2. L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
RC-168-QG-EN 2/21
• Display: 1.8" (46 mm) full-color TFT
• Approvals: FCC, CE, ISED Canada, and RCM certied;
IP55 rated
