Hunter 20091105 User manual

3 in 13 in 13 in 1
Form# 44825-01
20091105
©2009 Hunter Fan Co.
Portable Fan
Owner’s Manual
Model
90390
English

2©2009 Hunter Fan Co. 44825-01 20091105
TABLE OF CONTENTS
Introduction ............................................................. 3
Safety and Warnings................................................ 3
Unpacking............................................................... 5
Fan Assembly .......................................................... 5
Base Assembly......................................................... 6
Stand Fan 6
Height Adjustment 6
Table Fan 7
Wall Mount 7
Remote Battery Installation ........................................ 8
Operation - Fan/remote ........................................... 8
Maintenance............................................................ 9
Technical Support................................................... 10
Warranty............................................................... 10
Products ................................................................ 12

3©2009 Hunter Fan Co. 44825-01 20091105
INTRODUCTION
READ THIS ENTIRE MANUAL CAREFULLY BEFORE
BEGINNING INSTALLATION. SAVE THESE
INSTRUCTIONS FOR REFERENCE.
To reduce the risk of fire or electrical shock, DO NOT use
this fan with any solid-state speed control device.
When using electrical appliances, basic precautions
should always be taken to reduce the risk of fire, electric
shock and personal injury:
Read all instructions before using this fan.
1. Improper installation may result in the risk of fire,
electric shock or personal injury.
2. To prevent the risk of fire and electric shock, DO
NOT use the unit near windows. Rain and moisture
may create an electrical hazard.
3. The power plug must be removed from the power
socket when not in use, before cleaning, servicing,
maintenance and before moving to another location.
4. This product is intended for indoor use only. DO
NOT place fan in damp locations where humidity
is present.
5. The fan should be placed on a flat, stable surface or
tabletop to avoid overturning.
Thank you for choosing the Hunter 3 in 1 Fan. This
manual gives you complete instructions for assembling
and using your fan. Here are some the features you will
enjoy with your fan:
3An attractive design that enhances any decor
3A powerful motor for maximum air flow
3Three speeds to adjust your comfort level
3Remote controlled for added convenience
33 assembly options: floor stand, table top, or wall
mounted
3Parts of this fan, including the blades and the grill,
have been treated with Hunter’s Dust Armor protection,
making them less likely to attract dust and dirt.
SAFETY AND WARNINGS

4©2009 Hunter Fan Co. 44825-01 20091105
6. Use fan only for intended use, as described in this
instruction manual.
7. To protect against electrical shock, DO NOT immerse
unit, plug or cord in water or spray with liquids.
8. Close supervision is necessary when any appliance
is used by or near children.
9. NEVER insert fingers, pencils or any other objects
through the grill when the fan is running.
10. DO NOT operate any appliance with a damaged
cord or plug, after the appliance malfunctions or has
been dropped or damaged in any manner.
11. To disconnect, grip plug and pull from wall outlet.
NEVER pull on cord to disconnect from outlet.
12. ALWAYS use on a dry surface.
13. This product is intended for household use only and
not for commercial or industrial use.
14. DO NOT operate fan in the presence of explosive
and/or flammable fumes.
15. DO NOT place fan or any parts near an open flame,
cooking or any other heating appliances.
16. DO NOT use near curtains, plants, window
treatments, etc.
17. The rubber feet on this product may interact with
wood and cause damage to furniture. Do not place
on fine wood furniture.
18. Do not mix old and new batteries.
19. Do not mix alkaline, standard (carbon-zinc), or
rechargables (ni-cad, ni-mh, etc) batteries
20. This product conforms to UL STD 507 and is certified
to STD C22.2 No.113

5©2009 Hunter Fan Co. 44825-01 20091105
FAN ASSEMBLY
Figure 3.
Figure 4.
Figure 5.
1. Remove the Plastic Spinner (1) and the Plastic Nut (2)
from the fan motor housing. Figure 3.
2. Set the Rear Grill (3) against the front part of the
Motor Housing with the handle facing up. The 3 pins
on the motor housing should stick through the back
of the Rear Grill. Figure 4.
3. Screw the Plastic Nut (2) onto the fan and tightenly
firmly. Figure 4.
4. Remove the Plastic Sleeve from the motor housing
shaft and discard.
5. Install the Fan Blade (4) by sliding it over the motor
housing shaft, lining up the cut-outs on the back of
the Blade with the Retaining Pins on the Motor shaft.
Figure 5.
6. Screw the Spinner (1) onto the shaft counterclockwise
until secure. Figure 5.
7. Open the clips on the Front Grill
8. Set the Front Gill (5) into the notch on the bottom
of the Rear Grill (3) So the Hunter logo is facing
rightside up. Figure 6.
9. Close the clips On the Front Grill to hold both Grill
pieces in place. Insert the grill screw on the bottom of
the fan grill and tighten securely.
(1) Spinner
(2) Nut
(3) Rear Grill
(2) Nut
(4) Fan Blade
(1) Spinner
Figure 6.
(5) Front Guard
UNPACKING
As you unpack the fan, save the carton and packing
materials in case you want to move or ship the unit in
the future.
Carefully remove all items from the box.
NOTE: It is best to have someone hold the box while
you lift the fan and the protective packaging out of the
carton.
Make sure all shipping materials are removed from fan
before operating.

6©2009 Hunter Fan Co. 44825-01 20091105
Stand Fan
Figure 9.
BASE ASSEMBLY
1. Slide the Telescope Rod (7) into the top of the Stand
Base (8) of the stand fan. The pole is notched so it will
only fit into the base 1 way. Figure 7.
2. Secure the Telescope Rod (7) by screwing the Base
Nut (9) onto it from underneath the base. Figure 8.
3. Slide the Fan Assembly onto the telescope pole of the
base until it rests on the top of the pole. Figure 9.
4. tighten the screw on the back of the fan Assembly
until secure.
Warning: Do not force pole into the Stand Base
as damage to the Telescope Pole may occur. Do not
overtighten the Base Nut or screws.
Figure 7.
(7) Telescope Pole
(8) Stand Base
Figure 8.
(9) Base Nut
Height Adjustment
1. Grip the upper part of the telescope pole and loosen
the Adjustment Knob.
2. Raise or lower the pole to the desired height.
3. Turn the Adjustment Knob until it is secure.
screw

7©2009 Hunter Fan Co. 44825-01 20091105
Table Fan
Figure 10.
Figure 11.
1. Align the Fan Assembly over the Table Base (10) and
push together until secure. Figure 10.
2. Turn the Table Fan over and secure the 2 pieces
together using the 3 Table Base Screws. Figure 11. (10) Table
Base
Figure 12.
Figure 13.
Wall Mount
Before installing the Wall Mount Adapter, ensure the fan
location is close enough to a wall adapter that the fan
can be plugged in.
Caution: Due to the weight of this product, it is required
it be mounted into a wall stud. Failure to do so, could
cause the product to fall and/or damage the wall location
it is mounted in.
1. Place the Wall Mount Adapter (11) against the wall
and stud where you want to mount the fan.
2. Level the Wall Mount Adapter (11) for Asthetics.
3. Mark the hole locations on the wall with a pencil.
4. Using a 1/8 drill bit, drill the 2 holes for mounting.
5. Line the holes on the Wall Mount Adapter (11) to the
Wall holes and insert the 2 Wall Mount Screws and
tighten Securely. Figure 12.
6. Remove the phillips head screw from the base of the
Fan Assembly and insert the thumb screw.
7. Insert the Wall Mount Adapter (11) shaft into the Fan
assembly. Figure 13.
8. Tighten the Thumb screw in the back of the Fan
Assembly to secure fan.
(11) Wall Mount Adapter
Thumbscrew
Wall Stud

8©2009 Hunter Fan Co. 44825-01 20091105
OPERATION  FAN/REMOTE
Figure 15.
- turns the unit on and off.
- Adjust the speed of the unit between High, medium,
and low.
- Used to set the running time to 1, 2, or 4 hours.
- Indicates the current running speed of the fan.
TIME R
1
- Shows the number of hours the timer is set to run.
To operate your unit from the controls on the fan, Figure
15 or from the remote control, Figure 16:
1. Ensure the fan is plugged in.
2. Press the button to turn the unit on.
3. Adjust the speed by pressing the button until you
reach the desired speed indicated on the fan base.
4. To set the timer, ensure the unit is on and repeatedly
press the button until the fan console displays the
number of hours you want the unit to run.
5. To start/stop fan oscillation, push or pull the knob on
the back of the fan assembly, or push the oscillation
button on the remote control. Figure 17.
6. To adjust the angle of the fan, grasp both sides of the
grill, and gently tilt up or down.
TIMER
1
REMOTE BATTERY INSTALLATION
Figure 14.
1. Turn the Remote Control over and Remove the Battery
Cover from the back by gently pressing down on the
tab and sliding down on the tab. Figure 14.
2. Insert 2 “AAA” Batteries into the battery compartment,
ensuring the positive and negative ends of the
batteries are installed correctly.
3. Slide the Battery Cover back and snap into place.
Figure 16.
Oscillation Knob
Figure 17.

9©2009 Hunter Fan Co. 44825-01 20091105
MAINTENANCE
This fan is permanently lubricated and will not require
additional lubrication (oil) for the life of the fan.
This fan requires little maintenance and contains
no user serviceable parts. DO NOT try to fix
it yourself. Contact qualified service personnel
if servicing is needed.
Before cleaning, turn fan off and unplug from electrical
outlet. Wipe off excess dust with a lintfree cloth.
To ensure adequate air circulation to the motor, keep vents
located at the rear of the motor housing free from dust
accumulation. A vacuum cleaner hose can be used to
clean these vents.
DO NOT immerse the fan in water or any other liquid.
CLEANING THE GRILL AND BLADE:
1. Turn the fan off and unplug from the electrical outlet.
2. Disassemble the grills by carefully lifting the latches
around the outer ring.
3. Remove the front grill.
4. The blade may be removed by turning the Spinner
Knob clockwise.
3Use a dry or slightly damp lint free cloth to clean
the fan. Do not use a furniture polish or any other
cleaners that leave any residue, as they will damage
the protective Dust Armor.
3DO NOT allow water or any other liquid to get into
the motor housing or base.
3Reassemble the fan after blades and grills have dried
completely.
3DO NOT plug the fan into an electrical outlet until it
has been fully reassembled.

10©2009 Hunter Fan Co. 44825-01 20091105
If you have any additional questions or problems with
your Hunter Portable Fan, please call:
USA: 1-888-830-1326
Canada: 1-866-268-1936
Hours of operation are from 7:00 am to 7:00 pm
Monday - Friday and 8:00 am to 5:00 pm on Saturday,
Central Time. You may also contact us over the Internet at
www.hunterfan.com.
TECHNICAL SUPPORT
1. Problem
3Fan will not oscillate.
Solution
3Push down on the knob on top of motor housing to
activate oscillation.
2. Problem
3Can not adjust the angle of the fan.
Solution
3Gentle grasp the grill of the fan and tilt up or down.
3. Problem
3Remote control will not operate.
Solution
3Remove the battery cover and confirm the batteries
are installed correctly according to polarity markings.
Warranty
WARRANTY
The Hunter Fan Company makes the following limited
warranty to the user or consumer purchaser of this Hunter
Portable fan:
If your Hunter Portable Fan motor fails at any time within
one year after the date of sale to you due to a defect in
material or workmanship, labor to repair the defect will
be provided free of charge at our nearest service center
or our Service Department in Memphis, Tennessee. You
will be responsible for labor costs after this one-year
period. The foregoing limited warranty applies only to
the motor itself, and does not apply to electronic controls