Hunter 90437 User manual

Classic Tripod FanClassic Tripod FanClassic Tripod Fan
Owner’s Manual
English
Model
90437
90440
61903-01
R20141230

2
TABLE OF CONTENTS
Introduction ............................................................. 3
Safety and Warnings................................................ 3
Grounding............................................................... 5
Fused Plug ............................................................... 6
Unpacking............................................................... 7
Tripod Assembly....................................................... 7
Attaching Motor To Pole ........................................... 7
Grill Assembly ......................................................... 8
Operation.............................................................. 10
10
10
Off / Speed Selection
Oscillation 10
Height Adjustment
Maintenance.......................................................... 11
Technical Support................................................... 12
Troubleshooting ......................................................12
Warranty............................................................... 12
61903-01 R20141230

3
INTRODUCTION
READ AND SAVE THESE INSTRUCTIONS! To reduce
electrical appliances, basic precautions should always
be taken to reduce the risk of electric shock and
personal injury:
Read all instructions before using this fan.
1. Improper installation may result in the risk of
electric shock or personal injury.
2. To prevent the risk of and electric shock, DO
NOT use the unit near windows. Rain and moisture
may create an electrical hazard.
3. The power plug must be removed from the power
socket when not in use, before cleaning, servicing,
maintenance and before moving to another location.
4. DO NOT put fan in a damp place or where humidity
is high, such as a bathroom.
5. The fan should be placed on a stable surface to
avoid overturning.
6. Use fan only for intended use, as described in this
instruction manual.
7. To protect against electrical shock, DO NOT immerse
any part of the unit in water or spray with liquids.
Thank you for choosing the Hunter Oscillating Stand
Fan. This manual gives you complete instructions for
assembling and using your fan. Here are some ofthe
features you will enjoy with your fan:
An attractive design that enhances any decor
A power
Three speeds to adjust your comfort level
All metal construction
SAFETY AND WARNINGS
61903-01 R20141230
3
3
3
3
with any solid-state speed control device. When using

4
8. Close supervision is necessary when any appliance
is used near children.
9. NEVER insert fingers, pencils or any other objects
through the grill when the fan is running.
10. DO NOT operate any appliance with a damaged
cord or plug, after the appliance malfunctions or has
been dropped or damaged in any manner.
11. To disconnect, grip plug and pull from wall outlet.
NEVER yank on cord.
12. ALWAYS use on a dry surface.
13. This product is intended for household use only and
not for commercial or industrial use.
14. DO NOT operate fan in the presence of explosive
and/or flammable fumes.
15. DO NOT place fan or any parts near an open flame,
cooking or any other heating appliances.
16. DO NOT use near curtains, plants, window
treatments, etc.
17. This appliance has a grounded three-prong plug
and is suitable for grounded receptacle use only.
An adapter is available for connecting three-blade
grounding-type plugs to two-slot receptacles. The
adapter must be properly grounded. DO NOT
attempt to defeat the purpose of this safely feature.
18. The rubber feet on this product may interact with
wood and cause damage to furniture. Do not place
on fine wood furniture.
61903-01 R20141230

5
Figure 1
This appliance is for household use only and may be
plugged into any 120-volt AC electrical outlet (ordinary
household current). DO NOT use any other type of outlet.
This unit is suitable for grounded receptacle use only.
The power cord has a groundedplug as shown in
Figure 1, and must be usedwith an electrical outlet that
can accommodate the grounding pin. If your electrical
must purchase an adapter as shown in Figure 2.
NOTE: The adapters ARE NOT supplied with this fan.
Read, follow, and save the instructions that are included
with the adapter you choose. The green grounding lug
extending from the adapter must be connected to a
permanent ground such as a property grounded outlet
accommodate the grounding pin.
LINE CORD SAFETY TIPS
1. NEVER pull or yank on the cord or the appliance.
2.
3. To disconnect the appliance, grasp the plug and
remove it from the outlet.
4. Before each use, inspect the line cord for cuts and/
or abrasion marks. If any are found, the appliance
should be serviced and the line cord replaced. Please
return it to our Service Department or to an authorized
service representative.
5. NEVER wrapthe cord tightlyaround the
appliance, as this could place undue stress onthe
cord where it enters the appliance and couldcause
it tofray and break.
6. DO NOT operate appliance if the line cord shows any
damage, if the appliance works intermittently or stops
working entirely.
Grounded
Plug
Grounding Pin Grounded Outlet
Box Cover
WARNING
Figure 2
Grounded Outlet
Box Cover
Metal
Screw
Adapter
Grounding
Means
GROUNDING
61903-01 R20141230
outlet cannot accommodate the grounding pin, then you
box. Do not use an adapter if your electrical outlet can

6
Figure 3
This plug is a safety feature. It contains a safety device
(fuse) that should not be removed. Discard product if the
attachment plug is damaged. To reduce the risk of re,
electric shock and personal injury, DO NOT remove,
replace, repair or tamper with the originally supplied
to the safety device incorporated in this plug.
If the fuse fails, it is generally due to a short circuit or
circuit overload. Replace the fuse as per the instructions
below. If the replacement fuse fails, immediately
unplug the unit and contact our technical support
department for assistance.
Fuse Replacement:
1. To replace the fuse, rst turn the unit it off and unplug
it from the wall. Locate the door on top of the plug.
Figure 3.
2. Slide the door on top of the plug towards the blades.
Figure 4.
3. Carefully remove the fuse from the clips holding it on
the top and bottom. Figure 5.
Warning! Electrical Hazard! Only replace with a
fuse type and rating matching what was removed from
the product. If the product fails a second time,
immediately unplug it and contact our technical support
at 1-888-880-3267.
4. Gently push the fuse back into the pins that will hold
it in place.
Note: If the fuse is not seated properly, the unit will not
function.
5.
6. Plug the fan back in and resume use.
FUSED PLUG
Figure 4
Figure 5
61903-01 R20141230
plug. If the fan does not function properly, it may be due
Slide the door back over the fuse box in the plug.

7
TRIPOD ASSEMBLY
Figure 7
1. Loosen the three lower bolts and nuts from the Tripod
2. Tighten all upper and lower bolts and nuts using
10 mm wrenches.
3. Take the setscrew out of the plastic bag that was
attached to the foam of motor housing. Extend the
inner pole and install the setscrew into the screw hole
on the inner pole. Figure 7.
UNPACKING
As you unpack the fan, save the carton and packing
materials in case you want to move or ship the unit in the
future. Carefully remove all items from the box.
NOTE: It is best to have someone hold the box while
you lift the fan and the protective packaging out of the
carton. Make sure all shipping materials are removed
from fan before operating.
Setscrew
Inner Pole
Figure 8
Clip Button
1. Press the clip buttons in completely while sliding the
pole from the motor housing assembly into the inner
pole until the clip buttons appear through the hole in
the inner pole. Figure 8.
61903-01 R20141230
ATTACHING MOTOR TO POLE
Motor
Figure 6
Lower Bolt
Upper Bolt
the three lower bolts and nuts. Figure 6.
and save them. Fully extend the legs and install back

8
Figure 9
Figure 11
Figure 12 Figure 13
Grill Lines
Grill
Mounting
Screw
Top Tabs
12a
Motor
Notch
Fan Blade
123
61903-01 R20141230
GRILL ASSEMBLY
Note: The grill ring may be attached to the rear grills for
shipping purposes. If so, remove the grill ring by loosening
the grill ring screw.
1. Remove the four rear grill mounting screws from the
2. Make sure that the rear grill is positioned so that
three of the grill lines are completely between the top
the back of the grill to the four screw holes on the
front of the motor.
3.
partially install the four grill mounting screws.
Note: One of the grill mounting screws will have a star
washer on it, for grounding purposes. The other 3 screws
will not have a washer.
4. Loosen the screw on the back of the blade assembly.
Figure 12a. Slide the blade assembly onto the
5. Tighten the screw on the blade assembly to secure it
to the motor. Make sure that the end of the screw is
Caution: Ensure when tightening the screw on the back
of the fan blade, you tighten it on the flat part of the
motor shaft.
To attach the rear grill to the motor housing
the motor housing, and line up the four tabs on
motor housing. Figure 9.
tabs, Figure 10. Then place the rear grill against
Tighten all four screws. Figure 11.
motor shaft. Figure 12.
positioned within the notch on the shaft. Figure 13.
Figure 10

9
Figure 15
Figure 14
Figure 16
GRILL ASSEMBLY CONT.
Front Grill
Hunter Logo
Grill
Ring
Screw
Screw
6. Remove the grill ring from the front grill by loosening
the screw holding it.
7.
Hunter logo faces right side up and push together until
8. Expand the grill ring by loosening the screw that
9.
10. Tighten the screw to secure the grill ring over both
61903-01 R20141230
bottom.
turning the ring so that the screw is on the
Place the front grill against the rear grill so that the
Slide the grill ring over both front and rear grills
Rear Grill
the tabs on the grills hold them together. Figure 14.
secures it. Figure 15.
Figure 15.
the front and rear grill. Figure 16.

10
Figure 17
High
Medium
Low
Off
Figure 18
OPERATION
Turn the fan “ON” or “OFF” by moving the power/speed
lever. The power should always be OFF before
unplugging the fan. Toselect the speed, move the power/
speed lever from OFF to the desired speedsetting: O (off),
I(low), II (medium), III (high). Figure 17.
Off / Speed Selection
O
Height Adjustment
scillation
T
To adjust the height of the fan, turn the adjustment knob
counter-clockwise to loosen the inner pole. Adjust the
inner pole to the desired height, and firmly tighten the
adjustment knob in a clockwise direction. Figure 19.
o allow the fan to oscillate, push the knob beside the fan
speed control down. Pull up on the knob if oscillation is
not desired. Figure 18.
Oscillation
Knob
61903-01 R20141230
Figure 19
Adjustment
Knob