Hunter 44660 User manual

Ch T E M P
Form No. 44004-01 R030409
Your Model 44668/44665 thermostat
can read the temperature from up to
three weather-resistant sensors at a
distance of up to 75 feet.
Note: Distance my vary based on
building construction or other interfering
frequencies.
You can control the temperature from
one indoor sensor and/or thermostat,
with the second and third being a sensor
only. If you use multiple sensors, you
might want to number them. Simply use
a marker to write a number on the back
of each sensor. The remote sensors are
designed to either be mounted on a wall,
or set on a desk or side table.
Consult the Thermostat Instruction
Manual for instructions in setting the
thermostat to accommodate the remote
sensors.
You may also download directly from
Hunter Fan Company at www.hunterfan.
com/support.
1. Remove the four screws on the back
of the Remote Sensor. See Figure 1. The
Outer Cover will drop off.
2. Remove the Battery Compartment
Cover, which is underneath the Outer
Cover. See Figure 2.
Figure 1.
Outer Cover
4. Install two fresh AA alkaline batteries
into the Battery Compartment, being
careful to observe the battery polarities.
See Figure 4.
Figure 2.
Battery
Cover
3. Use the tip of a paper clip to set
the FIRST FOUR Remote Sensor DIP
Switches to any conguration you desire.
NOTE: Each sensor you use must have a
different setting. See Figure 3.
To set the remote sensor to display the
temperature in Fahrenheit, place the
FIFTH DIP switch in the DOWN position.
To set the remote sensor to display the
temperature in Celsius, place the FIFTH
DIP switch in the UP position.
Battery
Compartment
(Batteries
installed)
Figure 4.
1. When the batteries are installed, the
LCD Display will show the rst initializing
screen for approx. 2 seconds. See Figure
5.
2. The LCD Display will then show the
second initializing screen for approx. 10
seconds. See Figure 6.
Ch RHTEMP
C
%
Figure 5.
Ch
Figure 6.
Figure 3.
ON DIP
12 3 45
Model 44758 Remote Sensor
Owners Manual
Setup
InItIal Start-up
3. The LCD Display will then show the
normal operating screen. See Figure 7.
NOTE: It may take up to 30 seconds for
the thermostat to "pick-up" the sensor.
Ch TEMP
Figure 7.
Channel
4. The Remote Sensor Screen will
display the ambient temperature and, in
the bottom-left corner, a channel number
between 0 and 15. See Figure 7. This
will be the channel to which you will set
the thermostat to read the Remote Sensor.
See the Thermostat Instruction Manual,
page 14, Option 8.
5) Place the Battery Compartment Cover
over the Battery Compartment.
Wall MountIng
1. Replace the Outer Cover as shown in
Figure 8. Use the four screws to secure
the Outer Cover.

Fan Co.
7130 Goodlett Farms Pkwy,
Suite 400
MEMPHIS, TN 38016
© 2009 Hunter Fan Company
Form No. 44004-01 R030409
Wall-Mount
Indent
Figure 9.
1. Replace the Outer Cover as shown in
Figure 10. Use the four screws to secure
the Outer Cover.
2. Rest the Remote sensor on the
horizontal surface of your choice.
Figure 10.
Ch TEMP
Ch TEMP
If your Remote Sensor is set to show
the temperature in Celsius, the display
will show the ºC indication next to the
temperature. See Figure 11.
Ch TEMP
C
Figure 11
Temperature Measurement Range
Your Remote Sensor will show
temperatures from -40ºF to 122ºF (-40ºC
to 50ºC). If the temperature is greater
than 122ºF (50ºC), the LCD will show
“HI”. See Figure 12A. If the temperature
is lower than -40ºF (-40ºC), the LCD will
show “LO”. See Figure 12B.
Figure 12A Figure 12B
Low Battery Indication
When your Remote Sensor’s battery
is running low, the LCD will show the
ashing Low Battery Indication to remind
you to install two fresh AA Alkaline
batteries at your earliest convenience.
See Figure 13. At this point your Remote
Sensor will continue to function normally.
Figure 13.
Ch TEMP
Depleted Battery Indication
If your Remote Sensor’s battery is
depleted to the point that the LCD is
showing only the ashing Low Battery
Indication, as in Figure 14, your Remote
Sensor has ceased functioning and will
continue in this condition until two fresh
AA Alkaline batteries are installed.
Without further attention, the LCD will
eventually go blank.
Your Remote Sensor will return to normal
operation when fresh batteries are
installed.
Figure 14.
Problem: LCD is Blank.
Solution: Make certain your Remote
Sensor’s batteries are 1) installed
correctly, with polarities correctly
positioned, and 2) fresh.
Problem: Thermostat is not showing the
same temperature as the Remote Sensor.
Solution: Make certain you have
the correct Remote Sensor selected
at your thermostat (if you are using
more than one Remote Sensor). If you
require further assistance, call Hunter
Fan Technical Support at 1-888-830-
1326 from 7am to 7pm Central Time
Monday thru Friday and 8am to 5pm on
Saturday.
to Stand on a Surface
teMperature IndIcatIon
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation. This equipment has
been tested and found to comply with
the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Figure 8.
2. Use the provided screw to mount the
Remote Sensor on a wall or other vertical
surface. The back of the Remote Sensor
has a Wall-Mount Indent from which it
will hang from the provided screw. See
Figure 9.
troubleShootIng
technIcal