Husqvarna K 3000 Cut-n-Break User manual

EE
EEnn nngg ggll llii iiss sshh hh
K3000
K3000 Wet
Oper ator ′ s manual
Please r ead the operator’s manual carefully and make sure you understand the instructions
before using the machine.

KEY T O SYMBOLS
2 – English
Symbols on the mac hine:
W ARNING! The machine can be a
dangerous tool if used incorrectly or
carelessly, which can cause serious or
fatal injury to the operator or others.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Always wear:
• Approved protective helmet
• Approved hearing protection
• Protective goggles or a visor
This product is in accordance with
applicable EC directives.
WARNING! Dust forms when cutting,
which can cause injuries if inhaled. Use
an approved breathing mask. Always
provide for good ventilation.
WARNING! Sparks from the cutting
blade can cause fire in combustible
materials such as: petrol (gas), wood,
dry grass etc.
WARNING! Kickbacks can be sudden,
rapid and violent and can cause life
threatening injuries. Read and
understand the instructions in the
manual before using the machine.
En vironmental marking. Symbols on
the product or its packaging indicate that
this product cannot be handled as
domestic waste. It must instead be
submitted to an appropriate recycling
station for the recovery of electrical and
electronic equipment.
By ensuring that this product is taken care of correctly,
you can help to counteract the potential negative impact
on the environment and people that can otherwise result
through the incorrect waste management of this product.
For more detailed information about recycling this
product, contact your municipality, your domestic waste
service or the shop from where you purchased the
product.
Other symbols/decals on the mac hine refer to special
certification requirements for certain markets.
Symbols in the operator’ s
manual:
Inspection and/or maintenance should
be carried out with the motor switched
off and the plug disconnected.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
Protective goggles or a visor must be
worn.

CONTENTS
English – 3
Contents
KEY TO SYMBOLS
Symbols on the machine: ..................................... 2
Symbols in the operator’s manual: ....................... 2
CONTENTS
Contents ............................................................... 3
WHA T IS WHAT?
What is what on the po wer cutter - K3000? ......... 4
WHA T IS WHAT?
What is what on the po wer cutter - K3000 Wet? .. 5
GENERAL SAFETY PRECA UTIONS
Steps bef ore using a new power cutter ................ 6
Personal protective equipment ............................. 6
Machine ′ s safety equipment ................................. 7
SAFETY INSTR UCTIONS
Gener al safety warnings ....................................... 9
Cutting blades ...................................................... 11
General working instructions ................................ 13
ASSEMBL Y
Assemb ly .............................................................. 15
Fitting the cutting blade ........................................ 15
Guard for the blade ............................................... 15
ST ARTING AND STOPPING
Bef ore starting ...................................................... 16
Starting ................................................................. 16
Stopping ............................................................... 16
MAINTENANCE
Gener al ................................................................. 17
Cleaning ............................................................... 17
Electrical Feed ...................................................... 17
Replacing the carbon brushes .............................. 17
Bevel gear ............................................................ 18
Checking the drive shaft and flange washers ....... 18
Checking water connection with flow limiter ......... 18
Daily maintenance ................................................ 18
TECHNICAL D ATA
Cutting equipment ................................................ 20
Recommended cable dimensions ........................ 20
EC-declaration of conformity ................................ 21

4 – English
WHA T IS WHA T?
What is what on the po wer cutter - K3000?
1 Rear handle
2 Guard for the blade 14”
3 Cutting blade
4 Locking the axle
5 Front handle
6 Inspection covers
7 Power switch lock
8 Switch
9 Rating plate
10 Brush retainer
11 Carbon brushes
12 Guard for the blade 12” (Model version)
13 Connection for vacuum cleaner
14 Combination spanner
15 Operator ′ s manual

English – 5
WHA T IS WHA T?
What is what on the po wer cutter - K3000 Wet?
1 Rear handle
2 Guard for the blade
3 Water kit
4 Cutting blade
5 Locking the axle
6 Front handle
7 Inspection covers
8 Power switch lock
9 Switch
10 Water tap
11 Water connection with flow limiter
12 Rating plate
13 Brush retainer
14 Carbon brushes
15 Ground fault circuit interrupter (not for GB)
16 Combination spanner
17 Operator ′ s manual