HWAM I 40/55 User manual

Installation instructions EN
14.10.2020 / 97-9693
www.hwam.com
I 40/55

2

3
TABLE OF CONTENTS
TECHNICAL DATA ...............................................................................................................4
In general ..................................................................................................................................4
Safety..........................................................................................................................................4
Room requirements ...............................................................................................................4
Technical measures and data ................................................................................................4
Type plate and serial number ...............................................................................................5
Floor plate ................................................................................................................................5
Requirements for chimney and flue duct ..........................................................................5
INSTALLATION AND CONNECTION ...........................................................................6
In general ..................................................................................................................................6
Installation in rooms with non-combustible material .....................................................6
Installation in rooms with combustible material..............................................................6
Built-in example.......................................................................................................................7
Installation instructions....................................................................................................... 10

4
Technical daTa
In general
Congratulations on your new HWAM insert.We are pleased that you have chosen a HWAM insert and confident that it will give you much pleasure.
To ensure optimum operation and safety, we recommend that the installation should be carried out by an authorised HWAM retailer or a fitter
recommended by the retailer. For an overview of HWAM distributors, visit www.hwam.com under “Retailer locations”.
Safety
The installation of your HWAM insert must always comply with all European, national and local building regulations.The installation must be
carried out in accordance with the instructions in the installation and user manuals and subsequently registered with the local authorities. Upon
installation, the chimney sweep must approve the installation before you can start using the insert.All HWAM insert packaging material must be
handled in accordance with local waste management regulations.
Room requirements
Always ensure a supply of fresh combustion air to the room where the insert is to be installed.The insert uses approx. 12-19 m3 of air per hour
(depending on the setting of the air control lever).A window that can be opened or an adjustable air valve will be sufficient. It must not be possible
to block the adjustable air valve/grate. In newly built/airtight dwellings, we recommend that a fresh air system should be installed for the direct
supply of external air to the combustion.This fresh-air system may be bought separately.
Before installing the insert, make sure that the floor can carry the insert, the chimney and any other parts required for the installation.
Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should sometimes be treated as a flammable wall, in which
case we ask you to contact your local chimney sweep or glass producer to hear at what distance the insert should be kept from glass.
Technical measures and data
HWAM I 40/55 weighs 97 kg (total weight).
The following sketches show the different dimensions of the outer casing as well as the connecting dimensions for flue duct and fresh air system.
533
391
1818
385
614
149
218
318
308
A
770
569
385 385
147 147
734
Ø120 Ø120
18 18
367 367
DETAIL A
SCALE 1 : 1
Page 1 of 2
CAD-0190895
-
Sheet1
F
06-05-2019
nis Frigivet
Frigivet
nis 03-06-2019
G
Comment Init. Date Rev.
Frigivet nis
20-09-2019
H
nis
21-03-2019
DS/EN 22768-m
1:7
A3
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
Hwam I40-55 målskitse
Thickness: mm
533
391
1818
385
614
149
218
318
308
A
770
569
385 385
147 147
734
Ø120 Ø120
18 18
367 367
DETAIL A
SCALE 1 : 1
Page 1 of 2
CAD-0190895
-
Sheet1
F
06-05-2019
nis Frigivet
Frigivet
nis 03-06-2019
G
Comment Init. Date Rev.
Frigivet nis
20-09-2019
H
nis
21-03-2019
DS/EN 22768-m
1:7
A3
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
Hwam I40-55 målskitse
Thickness: mm
533
391
1818
385
614
149
218
318
308
A
770
569
385 385
147 147
734
Ø120 Ø120
18 18
367 367
DETAIL A
SCALE 1 : 1
Page 1 of 2
CAD-0190895
-
Sheet1
F
06-05-2019
nis Frigivet
Frigivet
nis 03-06-2019
G
Comment Init. Date Rev.
Frigivetnis
20-09-2019
H
nis
21-03-2019
DS/EN 22768-m
1:7
A3
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
Hwam I40-55 målskitse
Thickness: mm
533
391
1818
149
547
502
452
218
318
470
A
770
569
385 385
147 147
734
Ø120 Ø120
18 18
367 367
DETAIL A
SCALE 1 : 1
Page 1 of 2
CAD-0190950
-
Sheet1
C
06-05-2019
nis Frigivet
Frigivet
nis 03-06-2019
D
Comment Init. Date Rev.
Frigivet nis
20-09-2019
E
nis
28-03-2019
DS/EN 22768-m
1:7
A3
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
Hwam I40-55 målskitse røgafgang bagud
Thickness: mm

5
Test results from nominal test EN 13229:
Nominal heating effect 6.4 kW
Flue gas temperature EN 13229 measurement point 273ºC
Flue gas temperature measured in the outlet socket 326ºC
Exhaust gas flow 5.5 g/s
Efficiency 80%
CO at 13% O20.061 %
Test result based on NS 3058:
Particle emissions 2.65 g/kg
The declaration of performance can be downloaded from our website, www.hwam.com.
Type plate and serial number
The insert comes with type plate and serial number on the inside of the outer casing:
Locate the unique serial number of your insert and make a note of it below so that it is always easily accessible.The serial number must always
be provided when contacting your HWAM retailer.
Serial number (starts with “F4”):
Floor plate
European,national and local regulations must be observed in terms of the size and thickness of a non-combustible floor covering the floor in front
of the combustion chamber opening.Ask your HWAM retailer for assistance.
Requirements for chimney and flue duct
The height of the chimney must ensure sufficient draught and prevent any smoke nuisance.As a general rule, satisfactory draught conditions are
achieved if the chimney is 4 m above the stove and at least 80 cm above the ridge. If the chimney is placed at side walls, the top of the chimney
should always be higher than the ridge or the tallest point of the roof.Always be aware of any national and/or local regulations applying to thatched
roofs and the location of the chimneys.
The insert requires a minimum draught of 11 Pa (measured at EN 13229 measurement point). If measured just above the smoke flue socket, the
chimney draught must be 18-20 Pa.
The chimney must have a minimum clearing of Ø 150 mm.The chimney must be provided with an easily accessible cleaning door.The chimney and
flue duct must be of flue classT400 and be CE marked. Furthermore, it must have obtained the classification of G in soot fire testing.The required
distance to combustible material must be complied with in accordance with the brand label.Ask your HWAM retailer for further information.
S.nr.: S.nr.:
EAN S.nr.:
EN 13229:2001 /
A2:2 0 04
Inset app lia nces
fired b y solid fuel
HWAM A/S
Nydamsvej 53 - DK 8362 Hørning
Tel.: [phone]
Fax: [phone]
HWAM A/S
Nydamsvej 53
DK-8362 Hørning
Thermal output: 6.4 kW
Fuel types wood
Combustible materials – minimum di stance to non-combustible insulation:
- Side 50 mm
- Behind 50 mm
Information about insulation and other dimensions see installation instructions
Distance to furnishings front 1200 mm
CO Emission at 13% O20.061 % / 758 mg/m3
Particles at 13% O216 mg/m3
Energy effiency 80 %
Flue gas temperature EN 13229 measurement point 273 °C
Flue gas temperature measured in the outlet socket 326 °C
Laboratory registration number NB 1235
Test report 300-ELAB-2402-EN
300-ELAB-2471-EN
The appliance is capable of intermittent operation.
The appliance can be used in a shared flue.
Follow the user’s manual and use only recommended fuel.
Declaration of Performance: www.hwam.com/dop/i40 -55
Brensel ved
Partikulær utslipp 2,65 g/kg
Prøvningsinstitutt NB 1235
Prøvningsrapport 300-ELAB-2402-NS
NS 3 058
NS 3 059
HWAM I 40/55
19
Norm Österreich 15a B-VG 300-ELAB-2402-AUS
Thermal output: 6.4 kW
Energy effiency 80 %
CO 383 mg/MJ
Particles 11 mg/MJ
NOx63 mg/MJ
OGC 14 mg/MJ
15A

6
insTallaTion and connecTion
In general
HWAM I 40/55 consists of a separate outer casing as well as a separate insert that is pushed into place and connected when the outer casing
has been properly installed.We recommend installing a fresh air system that provides external air directly to the combustion (may be purchased
separately as an accessory). A fan kit that will improve heat utilisation and heat distribution in the room can also be purchased as an accessory.
The outer casing comes with 2 pre-cuts for the connection of tubes for the distribution of convection heat to other rooms.
Installation in rooms with non-combustible material
If the insert is installed in rooms where there is no combustible material, we recommend a distance between masonry and the outer casing of
5 mm as a minimum.This should prevent the brickwork from cracking when the outer casing expands during use.The masonry above the casing
must therefore be load bearing.
Installation in rooms with combustible material
If the insert is installed adjacent to combustible walls, a ventilated installation of non-combustible material such as calcium silicate or other mate-
rial with a thermal conductivity (EN 12667 @ 10 °C) of less than 0.068 W/m x K must be built. Requirements for this installation appear from
the illustrations in this installation guide.
Vent holes
The illustrations show minimum areas for vent holes.The area can be distributed on several vent holes. If the area is distributed on more than 2
vent holes for lower and upper holes respectively, the total area must be increased to compensate for a higher pressure loss. If grates are mounted
in the vent holes, the total vent hole area must be increased to compensate for the additional pressure loss caused by the grates.

7
Built-in example
3
C
C
Min. 300
Min. 1750
Min. 491
Min. 350
SECTION C-C
Convection opening
min. 563 cm²
Convection opening
min. 375 cm²
Hollow spaces must not be filled
with insulating materials
50 mm insulated
chimney
25 mm insulated
chimney
EE
Min. 700
Min. 50 Min. 50
Min. 185 Min. 350
Min. 1200
Min. 934
Min. 50
SECTION E-E
Brændbart materiale
Brandmur - min. 50mm kalciumsilikat
Isoleret skorsten
Distance from furniture to glass pane
Ceiling
Floor
Page 1 of 1
CAD-0190810
-
AUT Side
Sheet1
G
23-09-2019
nis Frigivet
Frigivet
nis 30-09-2019
H
Comment Init. Date Rev.
Frigivet nis
31-01-2020
I
nis
14-03-2019
3647.23
1:15
A3
CAD-0190810
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
3
C
C
Min. 400
Min. 1750
Min. 491
Min. 350
SECTION C-C
Convection opening
min. 563 cm²
Convection opening
min. 375 cm²
Hollow spaces must not be filled
with insulating materials
50 mm insulated
chimney
25 mm insulated
chimney
EE
Min. 700
Min. 50 Min. 50
Min. 185 Min. 350
Min. 1200
Min. 934
Min. 50
SECTION E-E
Brændbart materiale
Brandmur - min. 50mm kalciumsilikat
Isoleret skorsten
Distance from furniture to glass pane
Ceiling
Floor
Page 1 of 1
CAD-0190810
-
AUT Side
Sheet1
H
30-09-2019
nis Frigivet
Frigivet nis 31-01-2020
I
Comment Init. Date Rev.
Frigivet nis
11-03-2020
J
nis
14-03-2019
3645.76
1:15
A3
CAD-0190810
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
3
C
C
Min. 147
Min. 300
Min. 1750
Min. 350
SECTION C-C
Convection opening
min. 500 cm²
Convection opening
min. 750 cm²
Ceiling
Floor
25 mm insulated
chimney
50 mm insulated
chimney
Hollow spaces must not be filled
with insulating materials
EE
Min. 700
Min. 50 Min. 50
Min. 185* Min. 335*
Min. 1200
Min. 188
Min. 934
SECTION E-E
Distance from furniture to glass pane
Combustible material
Fire wall - min. 50 mm Calcium Silicate
Insulated chimney
Page 1 of 1
UK - Hwam I40-55 sikkerhedsafstande røgudgang op
-
Side
Sheet1
A
27-05-2019
nis Frigivet
Frigivet
nis 27-05-2019
B
Comment Init. Date Rev.
Frigivet nis
10-10-2019
C
nis
27-05-2019
3891.81
1:15
A3
CAD-0190810
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:

8
Built-in example
3
C
C
Min. 400
Min. 1750
Min. 491
Min. 350
Convection opening
min. 563 cm²
Convection opening
min. 375 cm²
Hollow spaces must not be filled
with insulating materials
25 mm insulated
chimney
50 mm insulated
chimney
Brændbart materiale
Brandmur - min. 50mm kalciumsilikat
Isoleret skorsten
Ceiling
Floor
Page 1 of 2
CAD-0191007
-
AUT Bagud
Sheet1
C
30-09-2019
nis Frigivet
Frigivet
nis 31-01-2020
D
Comment Init. Date Rev.
Frigivet nis
11-03-2020
E
nis
04-04-2019
3620813.94
1:15
A3
CAD-0190810
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
3
C
C
Min. 147
Min. 300
Min. 1750
Min. 350
SECTION C-C
Convection opening
min. 500 cm²
Convection opening
min. 750 cm²
Ceiling
Floor
25 mm insulated
chimney
50 mm insulated
chimney
Hollow spaces must not be filled
with insulating materials
EE
Min. 700
Min. 50 Min. 50
Min. 185* Min. 335*
Min. 1200
Min. 188
Min. 934
SECTION E-E
Distance from furniture to glass pane
Combustible material
Fire wall - min. 50 mm Calcium Silicate
Insulated chimney
Page 1 of 1
UK - Hwam I40-55 sikkerhedsafstande røgudgang op
-
Side
Sheet1
A
27-05-2019
nis Frigivet
Frigivet
nis 27-05-2019
B
Comment Init. Date Rev.
Frigivet nis
10-10-2019
C
nis
27-05-2019
3891.81
1:15
A3
CAD-0190810
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:

9
Built-in example
BB
Min. 1200
Min. 185
45°
Min. 50 Min. 50
Min. 700
Min. 50
Min. 934
Distance from furniture to glass pane
Page 1 of 2
CAD-0191009
-
Sheet1
A
04-04-2019
nis
Frigivetnis 05-04-2019
B
Comment Init. Date Rev.
Frigivet nis
31-01-2020
C
nis
04-04-2019
DS/EN 22768-m
1:12
A3
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:
Hwam I40-55 sidderhedsafstande skrå væg
Thickness: mm
3
C
C
Min. 147
Min. 300
Min. 1750
Min. 350
SECTION C-C
Convection opening
min. 500 cm²
Convection opening
min. 750 cm²
Ceiling
Floor
25 mm insulated
chimney
50 mm insulated
chimney
Hollow spaces must not be filled
with insulating materials
EE
Min. 700
Min. 50 Min. 50
Min. 185* Min. 335*
Min. 1200
Min. 188
Min. 934
SECTION E-E
Distance from furniture to glass pane
Combustible material
Fire wall - min. 50 mm Calcium Silicate
Insulated chimney
Page 1 of 1
UK - Hwam I40-55 sikkerhedsafstande røgudgang op
-
Side
Sheet1
A
27-05-2019
nis Frigivet
Frigivet
nis 27-05-2019
B
Comment Init. Date Rev.
Frigivet nis
10-10-2019
C
nis
27-05-2019
3891.81
1:15
A3
CAD-0190810
Com-Released
Created date:
Format:
Item number:
kg.
Part:
Weight:
Tolerance:
HWAM A/S
Nydamsvej 53-55
DK - 8362 Hørning
Tel. [phone]
Fax [phone]
Material:
Created by:
Configuration name:
Item:
Status:
Scale:
Drawing number:
Model:

10
Installation instructions
Install the outer casing and the insert as shown in the following illustrations.
Before mounting, any preliminary steps before the installation of fans and fresh air system must have been completed.
Polystyrene from packaging may be placed on the floor and serve as protection for the insert when it is lifted out of the casing. Note: It is VERY
important to secure the outer casing to the support with screws. Otherwise it may fall out during servicing when the insert is turned out of the
casing.
6 MM
5
1 2
3 4
6

11
87
11
9
13
10
12

12
14
17
16
19
18
15

13
20
2322
24
21

14

15