HWAM Classic 7 User manual

User’s Manual and Installation Guide
HWAM Classic 7 Wood Cook Stove
Distributed in the United States and Canada by:
HWAM North America
211 Reservoir Rd.
Plymouth, New Hampshire 03264
TEL: [phone]
www.hwamna.com
Manufactured by:
HWAM AS
Nydamsvej 53
Hørning, 8362
Denmark
TEL: [phone]
Web Site: www.hwam.com
HWAM Classic 7 with baking
door HWAM Classic 7 with soapstone top and baking door
This manual covers all versions of the HWAM Classic 7

Page 2
Table of Contents
1. Introduction ...........................................................................3
WARNINGS ............................................................................3
2. Installation ...........................................................................4
Pre Installation Check List ....................................................5
Clearance to combustibles ...................................................6
Floor protection ....................................................................6
Ceiling Height ......................................................................6
Combustible Wall Clearance for top vent installation .........6
Combustible Wall Clearance for rear vent installation .......7
Draft Requirements ..............................................................7
Chimney Installation .............................................................8
Top vent installation ..............................................................9
Chimney connection .............................................................9
Rear vent installation ..........................................................10
Mounting the connector pipe .............................................11
Combustible wall pass throughs ........................................11
Chimney height requirements ............................................14
3. Check the loose parts .........................................................16
4. Instructions for use .............................................................19
AshDrawer&AshGrate ..........................................................19
Baffle Plates & Skamol refractory .......................................20
Glass ........................................................................20
Smoke Detectors .......................................................20
Room Ventilation & Draft requirements ..................................21
5. Operation ..............................................................................22
Starting the stove ................................................................23
Refueling the stove ............................................................23
6. Maintenance ....................................................................... 24
Removing Skamol smoke plate for cleaning ......................25
Replacing broken Door Glass .............................................26
7. Troubleshooting ....................................................................27
Automatic Air Control System diagram ...................................28
Spare part list ..............................................................................29

Page 3
1. Introduction
We welcome you as a new owner of a HWAM wood-burning stove. This manual will
explain the installation, operation and maintenance of the HWAM wood-burning stove.
Please familiarize yourself with the owner’s manual before operating your stove and
save the manual for future reference.
Included are helpful hints and suggestions that will make the operation and maintenance
of your new stove an easier and more enjoyable experience.
Please read the entire manual carefully before you install and use your
new HWAM wood-burning stove. FAILURE TO FOLLOW INSTRUCTIONS
MAYRESULT IN PROPERTY DAMAGE, BODILYINJURY OR LOSS OF LIFE.
This manual contains important user information. Keep this manual with
the stove after installation is complete.
Safety and environmental testing
HWAM Classic 7 has been tested by Intertek Testing Services. of Fairview, Oregon,
and is safety listed by Intertek to UL 1482, ULC-S627.
The serial number is fixed to the stove and to the guarantee card. If you need
to contact the factory please refer to this serial number.
Items included:
1 instruction and maintenance manual, 1 guarantee card, 1 oven mitten, and 1
set of screws for the flue collar, and 1 detachable handle.
CONTACT YOUR LOCAL BUILDING OFFICIALS FOR INFORMATION ON
RESTRICTIONS AND INSTALLATION AND PERMIT REQUIREMENTS IN YOUR
AREA.
WARNINGS!
1. KEEP ASH DRAWER CLOSED DURING FIRING IN THIS STOVE. USE A METAL
CONTAINER WITH A TIGHT FITTING LID TO DISPOSE OF ASHES.
2. NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR ‘FRESHEN
UP’A FIRE IN THIS STOVE. KEEP ALL SUCH LIQUIDS WELL AWAY FROM
THE STOVE WHILE IT IS IN USE.
3. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE,
NAPHTHA OR ENGINE OIL.
4. THE STOVE IS HOT WHILE IN OPERATION. DO NOT TOUCH AND KEEP
CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN
BURNS. USE GLOVES WHEN STOKING THE FIRE.

Page 4
WARNINGS!
5. DO NOT CONNECT THIS STOVE TO A CHIMNEY FLUE CONNECTED TO
ANOTHER STOVE OR APPLIANCE.
6. DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
7. DO NOT INSTALL IN A MOBILE HOME.
8. BE SURE TO ALLOW AN ADEQUATE SOURCE OF FRESH AIR INTO THE
ROOM WHERE THE STOVE IS OPERATING .
9. DO NOT OPERATE THE STOVE WITHOUT THE FIREBOX REFRACTORY
PLATES PROPERLY INSTALLED.
10. BUILD FIRES DIRECTLY ON THE REFRACTORY BOTTOM PLATES
INSIDE THE STOVE.
11. DO NOT USE GRATES, IRONS OR ANY OTHER METHOD TO ELEVATE
THE FIRE.
What to do if you have a chimney fire
If you realize a chimney fire is occurring, follow these steps:
Get everyone out of the house, including yourself.
Call the fire department. If you can do so without risk to yourself, these additional
steps may help save your home. Remember, however, that homes are replace-
able, lives are not.
Put a chimney fire extinguisher into the stove.
Close the air controls on the stove and the damper on the chimney connector.
Use a garden hose to spray down the roof (not the chimney) so the fire won’t
spread to the rest of the structure.
Once it’s over, call a CSIA Certified Chimney Sweep to inspect for damage.
Chimney fire damage and repair normally is covered by homeowner insurance
policies.
2. Installation
WARNING
IF YOUR HWAM WOOD-BURNING STOVE IS NOT PROPERLY
INSTALLED, OPERATED AND MAINTAINED, A HOUSE FIRE
MAY RESULT. FOR YOUR SAFETY, FOLLOW ALL INSTALLA-
TION, OPERATION AND MAINTENANCE DIRECTIONS.

Page 5
Pre Installation Check List
Before you begin an installation, review your plans, check to see:
Your stove and chimney connector will be far enough from combustible material
to meet all clearance requirements.
The floor protection is large enough and is constructed properly to meet all
requirements.
You have all necessary permits from your local authorities. Your local building
official is the final authority for approving your installationas safe and in determining
that it meets all local and state building and safety codes.
The metal label permanently attached to the back of every HWAM wood-burning stove
shows that it has been tested to current UL and ULC safety standards, and gives the
name of the testing laboratory. Clearance and installation information is also printed on
the label. Local authorities will generally accept the label as evidence that, when the
stove is installed according to the information on the label and in this manual, the
installation meets codes and can be approved.
This wood stove must be connected to 1) a chimney complying with the requirements
for Type HTchimneys in the standard for Chimneys, Factory-Built, Residential Type and
Building HeatingAppliance, UL 103, or 2) a code-approved masonry chimney with a flue
liner. Due to the height if the HWAM Classic 7 flue outlet it is not possible to connect the
Classic 7 through an existing masonary or factory built fireplace.
For any unresolved questions about installation in the USA, refer to the national Fire
ProtectionAssociation’s publicationANSI/NFPA211 Standard for Chimneys, Fireplaces,
Vents and Solid Fuel BurningAppliances. For installation in Canada, refer to CSA CAN-
B365, Installation Code for Solid Fuel Burning Applications abd Equipment. These
standards are the basis for many national codes. They are nationally recognized and
are accepted by most local authorities. Your local dealer or your local building official
may have a copy of these regulations.
WARNING!
CHECK ALL LOCAL BUILDING AND SAFETY CODES BEFORE INSTALLATION.
THE INSTALLATION INSTRUCTIONS AND APPROPRIATE CODE REQUIREMENTS
MUST BE FOLLOWED EXACTLY AND WITHOUT COMPROMISE. ALTERATIONS
TO THE STOVE ARE NOT ALLOWED. DO NOT CONNECT THE STOVE TO A
CHIMNEY SYSTEM SERVING ANOTHER STOVE, APPLIANCE OR ANY AIR
DISTRIBUTION DUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID
THE MANUFACTURERS WARRANTY.
NOTE
If you plan to vent your stove into an existing masonry chimney, have the chimney

Page 6
inspected by a local fire marshal or qualified installer. Remember that the chimney and
its location on the roof heavily influents the stoves performance. An oversized flue may
not provide effective draft and a flue liner may be required. (Observe draft requirements).
Consult your dealer or qualified installer before final selection is made.
We advise you to leave enough room to enable cleaning between the stove and the
wall.
Clearance to combustibles
One of the main necessary precautions you must take, when installing a stove is to
leave sufficient space between the stove (top, sides, back, front, and under stove pipes)
and any material that can catch fire.
Floor protection
If the stove is to be installed on a combustible floor, the stove must be placed on a
noncombustible hearth pad, which extends 8" ( 200 mm measured from the legs) beyond
the stove sides and back, and 18" (455 mm) measured from side and back panels to the
front.
Ceiling height clearance
Do not install in an alcove or confined space and do not install in a room with a ceiling high
below 7’0” (210 cm).
&2/.4
&LOORPROTECTIONFOR#ANADAvCM
FROMUNITTOFRONTOFmOORPROTECTORAND
vCMTOTHESIDES
&LOOR0ROTECTORMUSTBEUNDERCONNECTOR
PIPEANDvCMTOTHESIDEFORATHROUGH
THEWALLCONlGURATION
v
v
53! v
#ANADAv
&,//202/4%#4/2
v

Page 7
Refer to the chimney connector manufacturer’s instructions concerning installation of
listed connector pipe, wall thimble and chimney.
#,%!2!.#%4/#/-"534)",%352&!#%3
,,!7%$)3
,,!74.%#!*$!
#
#
&
&
!
"
$
%
%
"
v
v
''
"!#+7!,, !$*!#%.47!,,
2%!24/0 6%.4/04)/.#%),).'
Combustible Wall Clearance for rear vent installation
In placing to stove the following clearances to combustible materials must be kept.
,,!7%$)3
#
!
"
"
v
'
"!#+7!,,

2%!26%.4/04)/.#%),).'
&KLPQH\
FRQQHFWRU
W\SH



$

%

&

*

³VLQJOH
ZDOOSLSH

´

´

´

´


PP

PP

PP

PP


&KLPQH\
FRQQHFWRU
W\SH








$
%
&
'
(
)
*
³6LQJOH
ZDOOSLSH

´
´
´ 
´
´
´ 
´

PP
PP

PP

PP
PP
PP

PP
Combustible Wall Clearance for top vent installation
In placing to stove the following clearances to combustible materials must be kept.

Page 8
The chimney draft depends on the weather conditions. In stormy weather, you may
reduce the chimney draft by closing the damper in the smoke pipe (if a damper has
been installed). If the chimney draft is strong, the combustion air supply should also be
reduced.
Chimney Installation
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER
APPLIANCE. DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
HWAM Classic 7 is listed for installation as a vertically top or rear vented wood-burning
stoveusinga listed classA(UL103HT)forCanada (CAN/ULC-S629) factory built chimney
exiting through the ceiling/attic/roof.
The inside diameter of the chimney and connector pipe must not be smaller than 6"
(152 cm) diameter. Single wall 24 gauge MSG (0.58 - 0.71 mm) , this may be used in
the room where the stove is installed, follow the chimney manufacturer’s instruction for
installation of chimney and chimney adapter. In Canada, where passage through wall,
or partition of combustible construction is desired, the installation shall conform to CAN/
CSA B365.
Factory Built Chimney
Whena metalprefabricated chimney is used,the manufacturer’sinstallation instructions
must be followed. You must also purchase (from the same manufacturer) and install the
ceiling support package or wall pass-through and “T” section package, fire stops (where
needed),insulationshield,roofflashing,chimneycap,etc. Maintain the proper clearance
tothestructureasrecommendedbythemanufacturer.Thechimney must be the required
height above the roof or other obstructions for safety and proper draft operation.
Masonry Chimney
Ensure that a masonry chimney meets the minimum standards of the National Fire
Protection Association (NFPA) by having it inspected by a professional. Make sure
there are no cracks, loose mortar or other signs of deterioration and blockage. Have
the chimney cleaned before the stove is installed and operated. When connecting the
Draft Requirements
HWAM Classic 7 is only one component of the total system. The venting system is
equally important for achieving the required flow of combustion air to the firebox and for
safely removing unwanted combustion by-products from the appliance. If the venting
system’s design does not promote these ends, the system may not function properly.
Poorly functioning venting systems may create performance problems as well as be a
safety hazard (i.e. .an oversized chimney may result in less than optimum performance.
Installations into a large, masonry chimney may require a liner to improve performance).
Adraft test should read greater than .04" W.C. (Inches Water Column) and less than 08"
W.C.

Page 9
Top vent installation
Required installation components:
Chimney cap
Insulated chimney
Storm collar
Roof flashing
Ceiling support box or joist shield/fire stop spacer
Chimney connector pipe
Chimney connector adapter
Chimney connector
The chimney connector is a single or walled pipe used
to connect the stove to the chimney. For use with the
HWAM wood-burning stoves the chimney connector
MUST be 6" in diameter, with a minimum thickness of
24 gauge black steel or 26 gauge blued steel
Aluminum and galvanized steel pipe is not acceptable
for use with the HWAM wood-burning stove. These
materials cannot withstand the extreme temperatures
ofawoodfireandcangiveofftoxicfumeswhen heated.
DO NOT USE THE CONNECTOR PIPE AS A
CHIMNEY
Each chimney connector or stove pipe section must
be connected to the stove flue collar and to each
other with the male (crimped) end toward the stove.
Each adjacent piece of connector must be fastened
with 3 screws.
stove through a combustible wall to a masonry chimney, special methods are needed.
Refer to Combustible Wall Chimney Connector Pass-Throughs on the following pages.

Page 10
This prevents any condensed or liquid creosote from running down the outside of the
pipe or the stove top. All joints, including the flue collar connection must be secured
with three sheet metal screws to ensure that the sections do not separate. For the best
performance the chimney connector should be as short and direct as possible, with no
morethanone 90 degree elbow. Themaximumhorizontalrunis36"and a recommended
total length of connector pipe should not exceed 10 feet. Always slope horizontal runs
upward ¼” per foot toward the chimney.
No part of the chimney connector may pass through an attic or roof space, closet or
other concealed-space, or through a floor ceiling. All sections of the chimney connectors
mustbeaccessible for cleaning. Where passagethrough a wall or partition of combustible
construction is desired, the installation must conform with NFPA211 or CAN/CSA-B365.
Rear vent installation
Forventingintoamasonryorabackstandingsteelchim-
ney through the top vent the top horizontal portion of a
singlewall connector pipe can belocated not closerthan
18" below a combustible ceiling.
From the factory the stove is prepared for top mounting
of the flue collar, but all HWAM wood-burning stoves
havean optional rear flue outlet, thereforethe flue collar
can be fitted either on the top or at the rear as required.
Mounting the flue collar for rear outlet:
Remove the cover plate on the rear of the stove.
Remove the inner cover plate. The flue collar is fitted
from the outside into the discharge hole of the firebox
in such a way that the bracket is located on the inside.
Place the cover plate on top so that this is just under
levelwiththe top plate, thereafterit is possible to mount
the external cover plate, for at smooth look.
Rear venting into a masonry or steel chimney through
a thimble vent configuration or other than described
here must follow local codes or NFPA 211 or CAN/
CSA_B365 guidelines and methods.

Page 11
Required installation components:
Chimney cap
Insulated chimney
Tee section
Tee support bracket
Chimney connector pipe
Wall thimble
Wall strap
Mounting the connector pipe to the stove
Pipe is placed in smoke outlet.
The 3 screws are screwed into the pipe to make a
mark in the pipe.
Drill a 5,2 mm hole at the markings from the 3
screws. .
Screw the 3 screws through the holes in the pipe,
so the pipe cannot be lifted of turned from the
stove
4OP/UTLET&LUE#OLLAR
2EAR/UTLET&LUE#OLLAR
3ET3CREW

Page 12
Method B 9" (228.6 mm) Clearance to Combustible Wall Member:
Using a 6" (152.4 mm) inside diameter, listed factory-built Solid-Pak chimney section
with insulation of 1"(25.4 mm) or more, build a wall pass-through with a minimum 9"
(228.6mm)airspace between the outer wall of the chimney lengthand wall combustibles.
Use sheet metal supports fastened securely to wall surfaces on all sides, to maintain the
9" (228.6 mm) air space. When fastening supports to chimney length, do not penetrate
the chimney liner (the inside wall of the Solid-Pak chimney). The inner end of the Solid-
Pak chimney section shall be flush with the inside of the masonry chimney flue, and
sealed with a non-water soluble refractory cement. Use this cement to also seal to the
brick masonry penetration
Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm) minimum wall
thickness clay liner, construct a wall pass-through. The clay liner must conform toASTM
C315 (Standard Specification for Clay Fire Linings) or its equivalent. Keep a minimum of
12" (304.8 mm) of brick masonry between the clay liner and wall combustibles. The clay
liner shall run from the brick masonry outer surface to the inner surface of the chimney
flue liner but not past the inner surface. Firmly grout or cement the clay liner in place to
the chimney flue liner.
Combustible Wall Chimney Connector Pass-Throughs
Method A 12” (304.8 mm) Clearance to Combustible Wall Member:
Minimum
12 in.(304,8 mm)
to combustibles
Minimum chimney clearance to brick
and combustibles 2 in. (50.8 mm)
Minimum clearance
12 in.(304.8 mm)
of brick
Chimney connector
Fire clay liner
Chimneyflue
Masony
chimney
Minimum chimney clearance from masony
to sheet steel supports and combustibles
2 in.(50.8 mm)
Minimum clearance
9 in.(228.6 mm) of bric
k
Air space
Masony chimney
Chimney
flue
Nonsoluble
refractor y
cement
Chimney length
flush with
inside of flue
Sheet steel suppo rt s
Chimney connector
Use chimney mfrs.
parts to attach
connector secur el y
Solid-insulated listed
factory-built chimney
length
Factory-built
chimney length
Air space 9 in.
(228.6 mm) min.

Page 13
Method D 2" (50.8 mm) Clearance to Combustible Wall Member:
Start with a solid-pak listed factory built chimney section at least 12" (304 mm) long,
with insulation of 1" (25.4 mm) or more, and an inside diameter of 8" (2 inches [51
mm] larger than the 6" [152.4 mm] chimney connector). Use this as a pass-through
for a minimum 24-gage single wall steel chimney connector. Keep solid-pak section
concentric with and spaced 1" (25.4 mm) off the chimney connector by way of sheet
metal support plates at both ends of chimney section. Cover opening with and support
chimney section on both sides with 24 gage minimum sheet metal supports. See that
the supports are fastened securely to wall surfaces on all sides. Make sure fasteners
used to secure chimney flue liner do not penetrate the liner.
Minimum chimney clearance to
sheet steel suppor ts and combustibles
2 in.(50.8 mm)
Two air channels
each 1 in. (25.4 mm)
Chimney connector
Minimum 6 in.(152.4 mm)
glass fiber insulation
Sheet steel suppo rts
Masony chimney
Chimney flue
Two ventilated air channels
each 1 in. (25.4 mm).
Construction of sheet steel.
Method C 6" (152.4 mm) Clearance to Combustible Wall Member:
Startingwith a minimum24gage(.024"[.61mm]) 6" (152.4 mm) metal chimney connector,
and a minimum 24 gage ventilated wall thimble which has two air channels of 1 in. (25.4
mm) each, construct a wall pass-through. There shall be a minimum 6" (152.4) mm
separationarea containingfiberglass insulation,from the outer surfaceof the wallthimble
to wall combustibles. Support the wall thimble, and cover its opening with a 24-gage
minimum sheet metal support. Maintain the 6" (152.4 mm) space. There should also be
a support sized to fit and hold the metal chimney connector. See that the supports are
fastened securely to wall surfaces on all sides. Make sure fasteners used to secure the
metal chimney connector do not penetrate chimney flue liner.
Sheet steel
suppor ts
Chimney
connector
Chimney
section
Air space 2 in.
(50.8 mm)
Minimum chimney clearance to
sheet steel supports and combustibles
2 in.(50.8 mm) Minimum clearance
2 in.(50.8 mm)
1 in.(25.4 mm) air
space to chimne y length
Chimney connector
Sheet steel support s
Chimney length
Masony chimney

Page 14
Chimney height requirements
The chimney must extend 3 feet above the level of roof penetration and a minimum of 2
feet higher than any roof surface within 10 feet. Check with your local building officials
for additional requirements for your area.
The condition of the chimney and height is very important; we suggest a total
minimum height of 15’ (4.5m). Measured From the floor level on which the stove is
installed.
Notes
1. Connectors to a masonry chimney, excepting method B, shall extend in
one continuous section through the wall pass-through system and the
chimney wall, to but not past the inner flue liner face.
2. Achimney connector shall not pass through an attic or roof space, closet
or similar concealed space, or a floor, or ceiling.

Page 15

Page 16
Cover plate
Your HWAM wood-burning stove is supplied with a loose cover plate for the shaking
grate. .This is a 3 mm thick iron plate. .It is placed on top of the shaking grate and
prevents the embers from falling into the ash pan. The cover plate is raised approx. 8
mm above the grate, thus ensuring that the automatically controlled primary
combustion air is distributed evenly at the base of the combustion chamber.
Cross section view of cover plate and shaker grate
3. Check the Stove Assembly
Before the stove is installed, you must ensure that all parts are fitted correctly,
especially the baffle plate #9.
Drawing A1: HWAM Classic 7 with baking door
These numbers correspond to the numbers on the drawing on the opposite page.
1. Air control 1
2. Air control 2
3. Air wash control
4. Bypass damper
5. Heat Shield
6. Cover plate. Should always cover the grate.
7. Log and ember guard. Should always be in place
8. Smoke shelf. Fits on top of side panels. Should always be pushed against the back
panel.
9. Rear smoke outlet. At the factory this is sealed with a cast cover plate, and an internal
cover plate. The smoke outlet is therefore hidden behind the plate.

Page 17
Exploded view of the Skamol re-
fractory plates. Skamol is a very
heat resistant and highly insulat-
ing material made of processed
vermiculite. This material is ca-
pable of service temperatures up
to 1150 C (2101 F) It is however
somewhat fragile. Care should be
used when handling these pieces
and when fueling the stove.
Drawing A1: HWAM Classic 7 with baking door
12
4
3
8
76
5
9

Page 18
Handle
The handle for the door is removable. Please note that it will fall off when the door is
closed. Hang the handle on the lower door frame when not in use. Do not hang the
handle on the oven door frame. It may become too hot. Always use a stove mitt
when refueling the stove.
2EMOVABLEHANDLE
INCLOSEDPOSITION
2EMOVABLEHANDLE
INOPENPOSITION

Page 19
Automatic Control (Drawing G)
Brilliant solutions are often simple little details which nevertheless make a huge
difference in our everyday lives. HWAM’s patented automatic system consists of a
small spring which automatically regulates the supply of air to the combustion
chamber. Simple, convenient operation - The automatic system optimizes the
combustion for you. All you need to do is to light up the stove and enjoy the flames
and the heat to the fullest. When you add more firewood, the system will
automatically readjust the stove to achieve the optimum combustion.
Lift off the rear panel. The starting point of the control arm should be checked. The
angle of the control arm on a cold stove is about 10° above horizontal.
It should move easily and bounce when you push it, no matter if the stove is cold or
hot. As the temperature rises and falls it must move smoothly. The slide gates must
be dry and clean and slide together unhindered. Control bars and slide gates may
need to be lubricated with WD40 (do not use oil).
10°
G.
4. Instructions for use
Ash Drawer
The ash drawer located below the fuel door is designed to make cleaning easier by
containing the ashes in a removable drawer. Replace the gasket as necessary to
ensure a tight seal.
Caution
Do not operate the stove with the ash drawer open or ajar, as this will produce
extreme temperatures within the stove (over-firing) and could result in a house fire.
Damage caused from over firing is not covered under the manufacturers limited
warranty. It will also clog the automatic control with ash and prevent it from working.
Ash Grate
Above the ash drawer, located in the floor of the firebox is a rotating ash grate to
facilitate transferring ashes from the firebox into the ash drawer. To operate this grate,
pull and push the handle placed in front of the stove in and out several times. Only
operate stove with the handle pushed all the way in.

Page 20
Skamol
Skamol refractory plates are delivered in all HWAM wood-burning stoves. When
mounting a baffle plate place it according to the description on page 25: Removing
Baffle for Cleaning. Make sure that it is placed symmetrically in the stove, i.e. with
even amounts of free air space on each side. We recommend that you treat the
Skamol refractory plates with care because it is a delicate material (not covered by
the limited warranty). Small cracks may arise in the Skamol because from minor water
content, especially if the stove is overheated during the first fire. These cracks do not
influence the performance of the stove and are not covered by the limited warranty.
Glass
The glass is a heat resistance ceramic glass that can withstand continuous
temperatures up to 1390°F (754°C). This temperature is well above the temperatures
in which you operate your stove. This stove is designed to provide a flow of air over
the inside of the glass. This air combined with high temperatures helps keep the glass
optimally clean when the air wash air intake is fully opened. When operating the stove
on low for extended periods of time, the glass may become dirty. A short, hot fire will
help clean off much of the normal soot buildup (see section 6: Troubleshooting). In
order to keep glass soot free the moisture content of the wood must be between 15
and 18%.
Smoke Detectors
HWAM strongly recommends installing smoke detectors throughout your home.
However, do not install them too close to the stove as the heat can activate them.
Gaskets
The stoves are equipped with ceramic gaskets to ensure the tightness of the doors and
the glass. These gaskets are wearing parts and must be changed from time to time.
Note the position of and remove worn gaskets. Remove the protective strip from the
back of the new gaskets and place the new gasket in the same position as the worn
one.
Protected Wall Reduced Clearances
Local codes in some areas will allow reduced clearances when the stove is installed
adjacent to a protected wall system. Your local building official must approve the
variance. Check your local building codes or with a qualified installer.
Room Ventilation & Combustion Air Supply
Provide for an adequate supply of air for combustion. Proper ventilation is essential
when using a solid fuel-burning appliance. The combustion process uses oxygen from
inside the dwelling and if there is not adequate make-up air (such as in newer homes
which are well insulated and weather tight), it may be difficult to obtain an adequate
draft in your chimney (caused by a shortage of air in the house). To correct this, it
may be necessary to crack a window on the windward side of the dwelling, or provide