Hyckes Hycooler go 8 User manual

Operating manual

Bedienungsanleitung

Notice d’utilisation

Gebruiksaanwijzing

12/24V compressor cooler

HyCooler Go 3

protected by copyright and design law. The underlying technical design and the

products contained herein may be protected by design, patent or be patent

pending. All rights are reserved.

Please read this manual carefully before starting the device. Keep it in a safe

place for future reference. If the device is passed on to another person, this

manual must be handed over to the user along with it.

Contents

1. Safety instructions ..............................................................................................page 4

2. Intended use..........................................................................................................page 4

3. Scope of delivery..................................................................................................page 5

4. Scope of functions...............................................................................................page 5

5. Control panel and display elements...............................................................page 6

6. Operation and use................................................................................................page 7

• Connecting the cooler

• Switching on the cooler

• App connection

• Battery power capacity indication

• Charging USB devices

• Detachable ice pack

7. Using the Powerpack (optional accessory)...................................................page 8

8. Advanced settings ...............................................................................................page 9

• Cooling mode

• Battery protection mode

• Temperature unit setting

• Factory reset

9. Cleaning and maintenance ............................................................................. page 10

• Cleaning

• Defrosting

• Storage

10. Troubleshooting ................................................................................................ page 11

11. Warranty .............................................................................................................. page 12

12. Technical data .................................................................................................... page 12

13. Disposal................................................................................................................ page 12

HMHCP202211-1

HyCooler Go HyCooler Go

WARNING! Failure to obey these warnings may result in death or serious injuries.

Please read and follow the instructions below carefully.

1 Safety instructions

– If the device is visibly damaged, do not operate and contact your supplier.

– Do not expose the device to any rain or water.

– Never place the device near open re or other heat sources such as gas grills, heaters etc.

– Do not store explosive substances like spray cans with a ammable propellant.

– Do not use the device in closed compartments or areas with none or minimal air ow.

– Ensure that there is a minimum of 50 to 100mm ventilation around the device at all times

when in use.

– If the power cable is damaged, it must be replaced to prevent safety hazards

– Only use the device with the original power cable supplied together with this appliance.

– Before every use the voltage specication must be checked corresponding to the used

energy supply.

– Never pull out the power cable from the socket only by the cable.

– Only qualied personnel is allowed to repair this device.

– Children aged from 8 years and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge can use this device, if they are

supervised or given instructions how to use the device in a safe way and must be aware

of the possible hazards involved.

– The device shall not be played with by children.

The insulation of this device contains ammable cyclopentane and requires special disposal

procedures. Deliver the device at the end of its life-cycle to an appropriate recycling centre.

2 Intended use

This product is designed to operate on a 12/24V power supply in a vehicle, stationary use

connecting the 110–230V adapter, or stand-alone operation using the optional battery. The

cooler is suitable for cooling drinks and food. It is intended to be used in household, travelling

and recreation applications, in accordance with these instructions.

The manufacturer accepts no liability for any injury or damage to the product resulting from;

incorrect assembly, connection, maintenance or use for other purposes than those described

in this manual. Please contact your local retailer, or the address listed in this manual, in case of

doubts or questions.

All information, specications and illustrations used in this document reect the most current

available at the time of publication. Without prior notice they can be subject of change.

Notice before use! At rst use, the device must be placed on a level surface for at least 6

hours, before turning it on.

When the device is being moved, make sure the angle will not be more than 30 degrees for a

maximum of 30 seconds. If the device is running, make sure the angle will not exceed 5 degrees.

Disconnect the device from the power supply after every use, before cleaning it or carrying out

maintenance.

During operation, do not leave the device opened for long periods. This prevents temperature

drops, optimises cooling performance and reduces power consumption.

3 Scope of delivery

– Cooler

– 12/24V power cable (DC)

– 110-230V adapter (AC)

4 Scope of functions

– Variable speed compressor combines maximum cooling performance and less energy

consumption compared to traditional compressors (up to 35%).

– High end insulation ensures ecient and fast cooling and freezing up to -20°C at all

circumstances

– HyCooler Powerpack battery oers stand-alone operation without power supply up to

24H (optional accessory).

– Control panel with LED display.

– USB connection for charging portable devices (5V - 2,0A).

– Integrated Bluetooth receiver for app control via mobile devices.

– Eco function for power saving or night mode to reduce noise.

– Intelligent battery protection system to prevent draining the vehicle battery.

– Collapsible carrying handle.

– Detachable ice pack (only for HyCooler Go 8 and Go 15 models).

HyCooler Go HyCooler Go

5 Control panel and display elements

Below an explanation of the control panel layout and possible display options.

6 Operation and use

Connecting the cooler

– Plug the supplied power cable into the cooler.

– Now connect the plug into a power supply for use on 12/24V.

– For use on an 110-230V power supply, the adapter can be connected instead.

Switching on the cooler

– Press the power button to switch on the cooler. Press the power button again to switch

o the cooler.

– The screen will power up and shows the actual cooling compartment temperature and

current settings.

– Use the + or – buttons to set the required temperature. After three seconds the

temperature will show the actual cooling compartment temperature again. Temperature

can be set in between values from -20 to 20°C (-4 to 68°F).

App connection

The cooler can be controlled using the Hyckes app, which can be installed on a mobile device

such as a phone or tablet. The app will give information of the current status while functions and

settings can be changed or controlled. Please follow the steps below to connect the cooler with

your mobile device.

– Download the Hyckes app from the Apple App Store or Google Play.

– When the cooler shows the Bluetooth icon on top of the display, it is ready for pairing

with a mobile device.

– Start the app on your mobile phone and follow the instructions on the screen.

– Once detected, the cooler will show ‘APP’ on the display.

– Conrm pairing by short pressing the settings button on the cooler.

– The cooler is now connected for mobile use.

Battery capacity indicator

When the optional HyCooler Powerpack is installed, the remaining battery capacity will be shown

on the display. If the cooler is connected with the AC power adapter and not switched on, the

battery charging status will be shown.

When connected to a 12/24V power supply, such as a vehicle’s starting or stationary battery, a

capacity indication of the vehicle’s battery will be shown on the display.

When connected to a 110-230V power supply using the adapter, the display will always

show the maximum battery capacity.

Charging USB devices

Small mobile devices can be charged via the integrated USB charging port. When connecting the

device to the USB port of the cooler, charging will start automatically.

Detachable ice pack

Inside the lid a detachable ice pack is installed (only for HyCooler Go 8 and Go 15 models). The

ice pack can be taken o and freely used inside the cooling compartment, or used at its original

position inside the lid.

– Take o the ice pack by rotating the knob 90°.

– Remove the cover on top of the ice pack and ll it with water (maximum 400 ml)

– Put the cover back on top of the ice pack.

Periodically change the water in order to prevent bacteria build-up. Do not drink the

water or let children play with the ice pack. If the cooler is not in use for a longer period,

drain the water from the ice pack and leave it to dry with the cover o.

7 Using the Powerpack (optional accessory)

At the bottom side of the cooler there is a compartment where an optional HyCooler Powerpack

can be installed. The Powerpack is a lithium battery which oers stand-alone operation, without

power supply, up to 24H.

The cooler will recognize the Powerpack automatically once installed. When the cooler is

connected to a 12/24V power supply in a vehicle, or a 110-230V power supply using the adapter,

the Powerpack will be automatically charged.

USB port

Temperature

Display

Power

Settings

Bluetooth

Temperature value

Temperature unit

Battery voltage

Battery protection mode

Cooling mode

Battery capacity

Power indicator

Power capacity indicator

Battery button

Charging port (optional 110-230V charger)

Release buttons

HyCooler Go HyCooler Go

Installing the Powerpack

– Remove the compartment cover by pressing both release buttons at the same time.

– Remove the battery connector protection cover inside the battery compartment. The

6-pin battery connector must be clearly visible (skip this step if no battery connector

protection is installed)

– Slide the Powerpack into the battery compartment of the cooler, while pressing both

release buttons at the same time.

– Release the buttons, the Powerpack is now locked and ready for use.

Using the Powerpack

– Long press the power button on the Powerpack to switch it on. Long press the power

button on the Powerpack again to switch o the battery.

– The power indicator will turn blue and the cooler will give a beep tone, indicating it is

ready for stand-alone use.

– The power indicator will turn green when the cooler is connected to a 12/24V power

supply in a vehicle, or a 110-230V power supply using the adapter, indicating the

Powerpack is being charged.

– The cooler can now be used stand-alone without power supply for up to 24H.

Remove the Powerpack from the cooler when it is left unused for a longer period of time.

Charging the Powerpack

– The Powerpack is equipped with a capacity indicator, showing the remaining battery

capacity. Also the cooler will show the remaining battery capacity on its display.

– When the cooler is connected to a 12/24V power supply in a vehicle, or a 110-230V power

supply using the adapter, the Powerpack will be automatically charged.

– Charging time will be around 4-8 hours, depending on the battery condition, charging

state and available input power.

It is recommended to connect the cooler to a 110-230V power supply, using the adapter,

for charging the battery. The 110-230V adapter will give maximum input power to the

cooler for optimal charging performance. When the cooler is switched o while charging

the battery, the charging time will be decreased while all available power will be used

for charging the battery.

An optional 110-230V battery charger is sold separately to charge the Powerpack without using

the cooler.

WARNING! Do not disassemble the battery. This may result in death or serious

injuries.

8 Advanced Settings

Cooling mode

This cooler is equipped with variable speed compressor technology. The electronics will

automatically vary the compressor speed depending on the conditions to reach and maintain the

set temperature.

MAX mode is the default setting for automatic and quick cooling.

ECO mode will lower the compressor speed and saves up to 35% power consumption. This mode

can also be used at night to reduce unwanted noises.

This feature can be controlled via the app, or changed on the cooler using the control panel:

– Short press the settings button. The current cooling mode setting will start to ash.

– Short press the settings button again to switch between modes.

– After three seconds the selected cooling mode will be set and becomes solid again on

the display .

Battery protection mode

The intelligent battery protection system will prevent the cooler to drain the vehicle battery.

If the supply voltage falls below a set level, the cooler will switch o. Once the voltage reaches

the restart voltage level, the cooler will automatically switch back on.

The battery protection mode can be set to three levels, following the table below:

12V 24V

OFF ON OFF ON

L - Low 8,5V 10,9V 21,3V 22,7V

M - Medium 10,1V 11,4V 22,3V 23,7V

H - High 11,1V 12,4V 24,3V 25,7V

High level should be set when the cooler is connected to a vehicle battery. Medium or

Low level should be set when the cooler is connected to a portable or backup battery.

This feature can be controlled via the app, or changed on the cooler using the control panel:

– Long press the settings button for three seconds. The current setting will start to ash.

– Short press the settings button again to switch between modes.

– After three seconds the selected battery protection mode will be set and becomes solid

again on the display.

Change temperature unit setting

The displayed temperature unit can be changed between °Celsius and °Fahrenheit using this

setting. This aects both the displayed unit in the app and on the cooler.

This feature can be controlled via the app, or changed on the cooler using the control panel:

– Switch o the cooler.

– Long press the settings button for ve seconds until the display shows ‘E1’.

– Short press the settings button until the display shows ‘E5’.

– Use the + and – buttons to switch between °C and °F.

– The selected temperature unit will start ashing.

– After three seconds the display turns o.

– The selected temperature unit is stored.

Factory reset

In case of any irregularities or recovery of the factory default settings, follow the procedure

below:

– Switch o the cooler.

– Long press the settings button for ve seconds until the display shows ‘E1’.

– Long press + and – buttons at the same time together for three seconds.

– A conrmation tone sounds for a successful factory reset.

HyCooler Go HyCooler Go

10 11

9 Cleaning and maintenance

Cleaning

Occasionally clean the cooler with a damp cloth and leave it to dry.

– Make sure the cooler is disconnected from the power supply before cleaning to avoid

electric shocks.

– If the optional Powerpack is installed, remove the battery from the compartment and

place the compartment cover back in place.

– Do not soak the device in water or clean it under running water.

– Do not use hard objects or abrasive cleaning agents as these can damage the device.

– Periodically check the air inlet and outlet vents for dust or dirt blocking the airow.

Defrosting

The cooler must be defrosted from time to time. Due to humidity, frost can settle on the

evaporator and will reduce the cooling capacity of the device.

– Make sure the cooler is disconnected from the power supply before cleaning to avoid

electric shocks.

– If the optional Powerpack is installed, remove the battery from the compartment and

place the compartment cover back in place.

– Never use sharp objects to defrost the device as they can damage the refrigerant circuit.

– Do not use mechanical objects or other means speeding up the defrosting process as

they can damage the device.

– Remove the melt water (by removing the drain plug if applicable)

– Clean with a damp cloth and leave it to dry.

Storage

When the device is left unused for a longer period of time:

– Disconnect the power cable and make sure the device is switched o.

– If the optional Powerpack is installed, remove the battery from the compartment and

place the compartment cover back in place.

– Leave the device for some time to defrost.

– Clean and dry the device.

– To prevent moulds and odours developing within the cooling compartment, take o the

lid or leave it opened.

10 Troubleshooting

When there are issues with the cooler during use, please refer to the troubleshooting list below.

If this does not resolve the issues, please contact a local retailer or visit www.hyckes.com.

Issue Possible cause or suggestion

The device does not function. Check if the power cable and plugs are connected

correct.

The power supply gives no voltage, try another

power outlet or socket.

A fuse has been blown, please check and replace

the fuse.

The device cannot be controlled by app. Restart the app on your mobile device, or (re)con-

nect Bluetooth. See paragraph ‘app connection’.

There is a bubbling or sizzling sound coming

from the cooling compartment.

This is a normal phenomenon, caused by the ow of

refrigerant.

The compressor is slightly noisy when start-

ing.

This is a normal phenomenon, the sound will reduce

after some time running.

A fault code is shown on the display. Please check the table below.

In case the display of the cooler shows a fault code (Fx), the following table explains the meaning

of this fault code and a possible cause and suggestion to resolve this fault.

Fault code Possible cause Suggestion

F1 Low input voltage Check supply battery power, or change

battery protection mode to medium or low. In

case the optional battery is installed; remove

or turn o the battery, or connect a power

supply to prevent draining the battery.

F2 Cooling fan over temperature Turn o the device for 5 minutes, then re-

start. Contact an authorised repair centre for