Hydromatic S4T Series Manual

SUBMERSIBLE
SOLIDS HANDLING PUMP
Mode s S4T, S8L, S8LA, and S12L
10/10
Ite # E-03-503
320 Fra e
Part # 5625-503-1
© 2010 Pentair Pu p Group, Inc.
Insta ation and Service Manua
NOTE! To the installer: Please ake sure
you provide this anual to the owner of
the equip ent or to the responsible party
who aintains the syste .
For use with product
bui t with USEM motor.

2
Thank you for purchasing your
Hydromatic®pump. To help
ensure years of trouble-free
op er a tion, please read the
fol low ing manual carefully.
Before Operation:
Read the following in struc tions
care ful ly. Reasonable care and
safe meth ods should be practiced.
Check local codes and
requirements before installation.
Attention:
This manual contains important
information for the safe use of
this product. Read this manual
completely before using this
product and refer to it often for
con tin ued safe product use.
DO NOT THROW AWAY OR
LOSE THIS AN U AL. Keep it
in a safe place so that you may
refer to it often.
Unpa king Pump:
Remove pump from carton. When
un pack ing unit, check for
con cealed damage. Claims for
damage must be made at the
receiving end through the delivery
carrier. Dam age cannot be
processed from the factory.
WARNING: Before handling
these pumps and ontrols,
always dis onne t the power
first. Do not smoke or use
sparkable ele tri al devi es or
flames in a septi (gaseous) or
possible septi sump.
IMPORTANT—Read all the
dire tions before repla ing
any parts.
WARNING: Before handling
these pumps, always dis onne t
the pow er first.
Do not smoke or use sparkable
ele tri al devi es or flames in a
septi (gaseous) or possible
septi sump.
Shipping:
When unpacking unit check for
con cealed damage. Claim for
damage must be made at the
receiving end through the
delivering carrier. Dam age cannot
be processed from the fac to ry.
Pumps Not Operating or
in Storage:
Pumps with carbon ceramic seals
must have impellers manually
rotated (6 revolutions) after
setting non-op er a tion al for 3
months or longer and prior to
electrical start-up.
Pumps with tungsten carbide seals
must have impellers manually
rotated (6 revolutions) after
setting non-op er a tion al for 3
weeks or longer and prior to
electrical start-up.
Pump:
The submersible pump is sup plied
for three phase only and for 460
and 575 volts. Pump is sup plied
with 35 feet of power cord and/or
35 feet of auxiliary control cord.
Longer cable lengths can be
furnished but must be specified at
time of order. Power cable is three
Genera
Information The Pump
wire with ground. Be sure ground
wire is con nect ed to a water pipe
or ground stake. The auxiliary
cable for seal fail ure and heat
sensors is four wire color coded.
Seal Failure:
An electrode probe is installed in
the seal chamber so if any water
enters the chamber through the
first seal the electrode will be
energized and a sig nal will be
transmitted to the sens ing unit at
ground surface causing a red light
to turn on. The electrode probe is
installed in all units but the
sensing unit is supplied at extra
cost and must be ordered.
In operation the seal failure unit
in di cates only that there is some
water in the seal chamber. The
pump will con tin ue to operate
without damage but the seal
should be checked im me di ate ly
after failure is indicated.
The sensing unit is recommended
on all installations as good
insurance against motor failure.
Heat Sensors —
Standard Equipment:
All motors have heat sensor units
em bed ded in the motor winding to
detect excessive heat. The heat
sen sors are set to trip at 150°C
(302°F), so will not op er ate unless
dangerous heat occurs. The
sensors automatically reset when
mo tor cools to safe tem per a ture.
The sensors are connected in
series with the motor starter coil
so that the starter is tripped if heat
sensor opens. The motor starter is
equipped with overload heaters so
all normal over loads are protected
by the starter.
Sump Level Control:
Sump level is controlled by
Hydromatic float switch con trols.

3
The float is held in position in the
sump by a weight at tached to the
power cord above the float. The
cord supports the float and is
adjusted for height from the
sur face.
Duplex systems use three
controls: one set at turn-off, one
set at turn-on for one pump, and
one set for turn-on for two pumps.
Pumps alternate op er a tion on each
successive cycle.
Two pumps operate together only
if sump level rises to the third or
over ride control. The override
control also brings on the second
pump in case of failure of the first
pump. The extra float is for alarm.
Triplex systems use four controls:
one set at turn-off, one set at
turn-on for one pump, one set
at turn-on for two pumps, and
one set at turn-on for three
pumps. Pumps alternate each
successive cycle.
Three pumps operate together
only if sump level rises to the
fourth control (second override).
This control also brings on
the third pump in case of failure
of either or both of the first
two pumps.
Alarm Controls:
The alarm level is usually set
above the override level so the
alarm will signal only if the
override level is ex ceed ed.
However, some engineers prefer
to have the alarm level set be low
the override level as it is pos si ble
for one pump to fail and the other
pump to operate on the override
level with the sump level never
reach ing the alarm level. This is
par tic u lar ly true in cases of low
inflow ca pac i ty.
Ele tri al Control Panel:
Hydromatic electrical equip ment
is installed in a weatherproof
NE A 3R enclosure. The
electrical equip ment includes a
main circuit breaker for each
pump, a magnetic starter with
overload protection for each
pump, an H-O-A switch and run
light for each pump, an electric
alternator and a transformer to
provide 115 volts for control for
control and circuit and alarms.
compound is needed to make
connections wa ter proof.
Wiring diagrams are provided
with the panel for making
connections. An extra set of
diagrams is included so that one
set can be used in the sump when
making connections. The size
wire to use from panel to sump
depends on motor size and
distance in feet.
Be sure each wire is checked so
that a wrong connection will not
be made. An ohmmeter or
egger can be used to check wire
continuity.
Installing Float Swit h Controls:
The controls are supported by a
mounting bracket that is attached
to sump wall, cover, or to the
NE A 4 junction box. Cord
snubbers are used to hold the cord
in place. Control level can be
changed at any time by loosening
the snubber and readjusting
cord height.
In either duplex or triplex
systems, the bottom of the lower
or turn-off control is set just above
the top of volute, so that the
volute will always be submerged
during the pumping cycle. The
second, or turn-on control, is set
about 24 inches above the lower
turn-off control.
ore distance between turn-on
and turn-off controls can be used,
but sewage may become septic,
and excessive solids may collect
for the pump to handle. A frequent
pumping cycle is recommended
for best operation.
Installing Pump in Sump:
Before installing pump in sump,
lay it on side and turn impeller
manually. Impeller may be
slightly stuck due to factory test
water, so it must be broken loose
with small bar or screwdriver in
edge of vanes. After break ing
loose, the impeller should turn
freely.
Clean all trash and sticks from
sump and connect pump to piping.
A check valve must be installed
on each pump. A gate or plug
valve in each pump discharge line
is also recommended. This valve
should be installed on the
discharge side of the check valve
so if it is necessary to service the
check valve, the line pressure can
be shut off.
NEMA IV Jun tion Box:
(Optional)
This must be used with 60 and
above horsepower pumps and
with all systems if the electrical
control panel is to be set remote
from the pumps. The Hydromatic
NE A 4 junction box is provided
with com pres sion connectors for
sealing all wires. No sealing
Insta ation
Instructions

4
In a duplex system the third or
override control is usually set
about 6 inches above the one
pump turn-on control.
In a triplex system the third or
override control is usually set 24
inches above the one pump
turn-on control, and the fourth or
second override control is 24
inches higher.
If an alarm system is used, this
control is usually set about 6
inches above the override control.
As described previously, some
engineers prefer to have the
alarm control set below the
override control.
Making Ele tri al Conne tions:
All electrical wiring must be in
ac cor dance with local codes, and
only competent electricians
should make the in stal la tions.
Complete wiring diagrams are
glued to the inside cover of the
panel, and an additional set of
prints is included for use in
making the installation. All wires
should be checked for grounds
with an ohm meter or egger after
the con nec tions are made. This is
important, as one grounded wire
can cause considerable trouble.
(See Fig. 1.)
IMPORTANT: If equipment is
not properly wired and
prote ted as re om mend ed, the
motor guarantee is void.
Heat Sensors and Seal Failure
Conne tions:
Be sure heat sensor wires are
con nect ed in series with the
starter coil. Con nec tions are
provided on the terminal strip. See
wiring diagram. If seal failure unit
is used, connect as shown with
seal failure system. If seal failure
unit is not used, the two seal
failure wires are left open. Do not
connect power to these lines at
any time. (See Figs. 2 and 3.)
Starting System:
1. Turn H-O-A switch to
Off position and then turn on
main circuit breakers.
2. Open all discharge valves and
allow water to rise in sump.
3. Turn H-O-A switch to Hand
posi tion on one pump and
notice oper ation. If pump is
noisy and vibrates, rotation is
wrong. To change rotation,
interchange any two line leads
to motor 3ø only. Do not
interchange main incoming
lines. If duplex system, check
second pump in same manner.
4. Now set both H-O-A switches
to Auto position and allow
water to rise in sump until one
pump starts. Allow pump to
operate until level drops to
turn-off point.
5. Allow sump level to rise to
start other pump. Notice run
Fig. 1
HEAT SENSORS AND SEAL FAILURE CONNECTIONS
FOR ANY VOLTAGE MOTOR
ELECTRODE
HEAT SENSORS
IN MOTOR
WINDINGS
WHITEBLACK
HEAT SENSORS SEAL FAILURE
RED DARK
GREEN
Fig. 2
Fig. 3
DUAL VOLTAGE
3 PHASE MOTOR WIRING
230V 3ø 460V 3ø
GREEN GREEN
R
(L3)
W
(L2)
BL
(L1)
R
(L3)
W
(L2)
BL
(L1)
12 3
78 9
45 6
12 3
78 9
45 6
WARNING
BLACK
COIL
ON-OFF
SWITCH
L1 THERMOSTATS
IN SERIES
WHITE
L2
TWO WIRE CONTROL OFFERING AUTOMATIC RESET
THERMOSTATS
IN SERIES
WHITE
L2
BLACK
THREE WIRE CONTROL OFFERING AUTOMATIC RESET
L1
COIL OL OLSTART
IN CERTAIN APPLICATIONS THE NEC MAY REQUIRE THREE OVERLOAD RELAYS
COLOR PURPOSE
DARK GREEN SEAL FAILURE
RED SEAL FAILURE
BLACK HEAT SENSOR
WHITE HEAT SENSOR
WARRANTY IS VOID IF HEAT SENSORS ARE NOT
CONNECTED AS SHOWN (IN SERIES WITH CONTACTOR OIL)
DESIGNATION FOR OPTIONAL
SEAL FAILURE & SENSOR CORD
See Wiring Diagram of seal failure
unit #4673 or 4674 for connecting
dark green and red wires. If seal fail-
ure unit #4673 or 4674 is not used,
leave dark green and red wires open.
Pump
Operations

5
lights on panel. Pumps should
alternate on each successive
cycle of op er a tion.
6. Turn both H-O-A switches
to Off position and allow
sump to fill to the override
control level.
7. Turn both switches to Auto
position and both pumps
should start and operate
together until level drops to
turn-off point.
8. Repeat this operation
cycle several times before
leaving job.
9. Check voltage when pumps are
operating and check the
amp draw of each pump.
Check amps on each wire, as
sometimes a high leg will
exist. One leg can be
somewhat higher (5 to 10%)
without causing trouble. For
excessive amp draw on one
leg, the power company should
be consulted.
expected to operate for many
years on normal sewage pumping
without failure.
Servi ing Instru tions:
IMPORTANT — Read all
in stru tions before repla ing
any parts.
WARNING: Before handling
these pumps and ontrols,
always dis on ne t the power
first.
Do not smoke or use sparkable
ele tri al devi es or flames in
a sep ti (gaseous) or possible
septi sump.
Field Servi e on Motor:
All submersible motors can be
serviced (out of warranty) in the
field by any reliable motor
service shop. Any pump (in
warranty) must be returned to the
factory for service or repaired in
an authorized Hydromatic service
center. Charges will not be
allowed if (in warranty) pump is
taken to a motor repair shop that is
not an authorized
Hydromatic
service center.
When field service is performed
on a pump, these instructions
should be carefully followed.
Repla ing Stator:
If motor winding is burned or
shorted, it can be rewound or
replaced with new factory wound
stator. Refer to sectional drawing
of pump and motor and use
the following steps to remove and
replace stator.
1. If stator only is damaged, it
may not be necessary to
completely dismantle pump
as stator and housing can be
As the motors are oil filled, no
lubrication or other maintenance
is required.
If a seal failure unit is used,
no attention is necessary as
long as the seal shows
satisfactory operation.
If seal failure is not used, the
pump should be lifted once every
two years and the oil drained
from the seal chamber to check
for water.
If the pump is used on a
HYDR-O-RAIL system, it
should be lifted once every six
months and checked for corrosion
and wear.
Generally, these pumps give very
reliable service, and can be
Pump
Maintenance
lifted from pump without
disturbing seals or bearings.
2. Drain all oil from upper
housing, remove drain plug in
bottom of stator housing and
remove plug in top of housing
to allow air to enter.
3. After chamber is drained,
remove hold-down bolts
and lift off. Use care in
lifting as the seal failure
connecting wire must be
dis con nect ed before housing
is com plete ly removed. See
sectional drawing.
4. Set assembly on bench and
remove connection box. When
box is lifted off, connection
wires to motor will be
exposed. These wires will
probably be burned, but each
wire is tagged with a metal
marker giving wire number.
Cut the wires.
If the leads to the connection
box are burned, a complete
new con nec tion box with new
wire must be used. The wires
are potted in with sealing
compound and a new unit
must be obtained from the
factory. The old con nec tion
box can be returned to the
factory for partial credit.
5. The stator is held in the
housing with a bolted-in
retaining ring and prevented
from rotating by a key.
6. Remove the retaining ring and
socket head cap screw.
7. After ring is removed, turn
housing upright and bump on
hard wood blocks. This should
jar the stator loose and allow it
to drop out.
8. Thoroughly clean housing
before replacing new stator.
Replace stator and make all
wire con nec tions to the
connection box before
replacing housing on pump.

6
This is important as leads must
be tucked behind the windings
by using hands up through
rotor core.
IMPORTANT: Use only butt
onne tors on the wires.
Do not tape leads as oil will
de te ri o rate the tape and ause
damage to stator and bearings.
9. Drain oil from seal chamber.
If oil is clean and no water
is present, seals can be
considered sat is fac to ry to
reuse.
10.Check top bearing. If clean and
does not turn rough, bearings
can be reused and it is not
necessary to completely
dismantle pump to change
bearings. If bearings are
damaged with dirt or heat,
they must be re placed. See
additional instructions on
replacing seals and bearings.
11.Replace stator housing onto
seal chamber and bolt in place.
Be sure seal failure wire is
connected before housing is
assembled. (See Figs. 2 and 3.)
Be sure back-off screws have
been loosened so that parts can
come metal to metal. Be
sure O-ring seal has been
replaced. If O-ring is nicked or
cut, replace with new ones.
This applies to all O-rings used
in assembly.
12.After all leads are reconnected
in the connection box, make
a high voltage ground test on
each wire. The only wire that
should show ground is the
green power lead and the
ground lead in the auxiliary
control cable.
13.For safety, complete pump
should be air checked under
water for leaks.
If seals were OK, refill seal
chamber with oil. Lay pump
on side for this oil filling
with oil fill hole upright.
Do not completely fill; leave
oil about 1 inch below plug
hole. Use only Hydromatic
submersible oil in this
chamber. Replace plug; use
Permatex on threads. Install air
valve in top plug opening of
motor housing and charge
housing with about 10 psi of
air. Be sure air is dry. Do
not use air line where water
may be trapped in the line.
Submerge complete unit under
water and check for leaks.
14.Refill motor chamber with oil.
Use high grade transformer
oil or Hydromatic special
sub mers ible oil. Fill chamber
until oil covers top of the
windings. Leave air space in
the top for expansion. Use
Permatex on plug threads.
Repla ing Seals and Bearings:
1. Drain all oil from motor
chamber and seal chamber
as described.
2. Remove motor housing as
described.
3. Remove bolts that hold seal
chamber to pump housing. Use
back-off screws to break loose.
With hardwood block, tape end
of impeller to loosen from
shaft. When free, remove
impeller from shaft.
4. Lift rotating assembly from
pump case and place on bench.
5. Impeller Removal: Hold rotor
and remove bolt and washer
from impeller end of shaft,
then thread bolt back into
shaft. The impeller is keyed
to the shaft, so by using a
screw driv er on opposite sides
behind the im pel ler, apply
force then tap on the end of the
bolt to break impeller loose
from taper shaft. Remove
impeller.
6. Remove key and pry on each
side of shoulder of shaft sleeve
to remove. Seal should come
off with sleeve. If sleeve is not
free, leave in place and push
off when seal plate is
removed.
7. To remove seal plate take
out socket head flat screws
and using screws in back-off
holes pry plate loose. This will
also force seal off if not
already re moved.
8. Remove snap ring that holds
upper seal. Pull seal if it is
free. If not free, it can be
forced off when shaft is
removed.
9. Set seal housing assembly in
upright position and bump end
of shaft on hardwood block.
This will push the bearing
from the housing and will
force upper seal from shaft.
10.Use bearing puller to remove
bearings. Replace with new
bearings. Press only on
inner face of bearing when
replacing. Pressing on outer
face can damage the bearing.
Bear ings are standard size that
can be obtained from any
bearing supply house or can
be obtained from Hydromatic
factory.
11.IMPORTANT—Do not use
any of the old seal parts.
Replace with all new seals.
12.Thoroughly clean all castings
before replacing seals. One
grain of dirt between the seal
faces can cause failure.
13.Examine all O-Rings for nicks
before reusing.
14.Be sure key is in place in
notch of shaft sleeve to
prevent sleeve from turning.

7
15.Use Locktite on socket head
locking screw in end of shaft.
16.Before refilling chamber with
oil, air test as described above.
17.Refill both chambers with oil
as described above.
18.Always check all leads with
high voltage or with egger
for grounds before operating
the pump.
Below is a list of common
problems and the probable causes:
Pump will not start.
1. No power to the motor. Check
for blown fuse or open
circuit breaker.
2. Selector switch may be in the
Off position.
3. Control circuit transformer
fuse may be blown.
4. Overload heater on starter may
be tripped. Push to reset.
Pump will not start and
overload heaters trip.
1. Turn off power and check
motor leads with egger or
ohmmeter for possible ground.
2. Check resistance of motor
windings. All 3 phases should
show the same reading.
3. If no grounds exist and
the motor windings check
OK, remove pump from sump
and check for clogged or
blocked impeller.
Pump operates with sele tor
swit h in Hand position but will
not operate in Auto position.
1. This indicates trouble in the
level control or the alternator
relay.
2. To check for defective control
put selector switch in Auto
position and turn off main
power. Put a jumper wire
between 2 and 3 on terminal
strip. Turn on power and
if pump starts, trouble is in
lower control. Replace control.
If pump does not start, turn off
power, remove jumper from 2
and 3 and put jumper wire
between 1 and 2 ter mi nals.
Turn on power and if pump
starts, trouble is in upper
control. Replace control.
If pump does not start, turn off
power and put jumper between
2 and 3 and 1 and 2 and turn on
power. If pump starts, both
lower and upper controls are
defective. If pump still does
not start, trouble is in the
alternating relay. Replace with
new relay.
Pump runs but will not shut off.
1. Pump may be air locked. Turn
pump off and let set for
several minutes, then restart.
2. Lower float control may be
hung-up in the closed position.
Check in sump to be sure
control is free.
3. Selector switch may be in the
Hand position.
Pump does not deliver proper
apa ity.
1. Discharge gate valve may be
partially closed or partially
clogged.
2. Check valve may be partially
clogged. Raise level up and
down to clear.
3. Pump may be running in
wrong direction. Low speed
pumps can operate in reverse
direction without much noise
or vibration.
4. Discharge head may be too
high. Check total head
with gauge when pump is
operating. Total head is
discharge gauge pressure
converted to feet plus vertical
height from water level in
sump to center line of pressure
gauge in discharge line. Gauge
should be installed on pump
side of all valves. ultiply
gauge pressure in pounds by
2.31 to get head in feet.
5. If pump has been in service for
some time and capacity falls
off, remove pump and check
for wear or clogged impeller.
Motor stops and then restarts
after short period but overload
heaters in starter do not trip.
1. This indicates heat sensors in
the motor are tripping due
to ex ces sive heat. Impeller
may be partially clogged
giving a sus tained overload
but not high enough to trip
overload heater switch.
2. otor may be operating out of
liquid due to a failed level
control. All Hydromatic
sub mers ible motors can
operate for extended periods
out of water without burning
up the winding, but the heat
sensors give motor prolonged
life by con trol ling winding
temperature.
3. Pump may be operating on
a short cycle due to sump
being too small or from water
returning to sump due to a
leaking check valve.
Pump
Troub eshooting

8
Motor End
Components

9
S4T S8L
S8LA S12L
Wet End
Components

10
A1 65-006-1 BEARING – BALL (UPPER) R 1
A2 65-023-1 BEARING – BALL (LOWER) R 1
A3 150-019-1 O-RING 1
A4 150-032-1 O-RING SC 1
A5 150-038-1 O-RING SCI 2
A6 150-057-1 O-RING SCI 1
A7 150-108-1 O-RING (VITON) SC 1
A8 239-035-1 SCREW – HHC 1/2-13 x 5-1/4 4
A9 239-038-1 SCREW – HHC 1/2-13 x 7-1/4 12
A10 556-007-1 SCREW – CAP (HEX SOC.) 6
A11 557-000-1 CONNECTOR – WIRE 3
A12 975-010-1 RING – RETAINING 1
A13 975-014-1 RING – RETAINING 1
A14 1272-001-3 TUBING – NYLON 1
A15 1664-008-1 PLUG – PIPE 3/8 SKT HD BRASS 3
A16 2310-004-3 SLEEVE – SHAFT SC 1
A17 2855-001-1 KEY – SQUARE 3/8 1
A18 2921-001-1 SCREW – CAP (FL. HD SOC) 4
A19 4580-001-1 SCREW – DRIVE 4
A20 6000-011-1 WIRE w/TERMINAL 14 GA. RED 1
A21 6579-002-1 KEY – SQUARE 1/4 1
A22 7398-000-2 HOUSING – SEAL 1
A23 7400-004-2 HOUSING – MOTOR 1
A24 7401-100-2 HOUSING – BEARING 1
A25 8206-000-1 PLATE – INSTR (DRAIN) 1
A26 8206-001-1 PLATE – INSTR (FILL & DRAIN) 1
A27 8354-000-3 RING – RETAINING STATOR 1
A28 8472-002-5 SEAL FAILURE ASS'Y 1
A29 9176-000-1 SLEEVE – WIRE 6
A30 11065-002-3 SCREEN 3.81 DIA. 1
A31 12672A002 CONNECTOR – BUTT 3
A32 13425-023-1 NAMEPLATE 1
Ref. Part Part
No. No. Descriptio Qty.
A33 19101A017 SCREW – CAP HEX SST 3/8 6
A34 19103A052 SCREW – CAP HEX SST 1/2 6
A35 24709110000 OIL – TRANSFORMER 10.5
A36 13424-004-1 LABEL – HEAT SENSOR 1
C1 3718-000-1 SEAL Carbon Ceramic / Buna-n S 1
C2 3718-000-1 SEAL Carbon Ceramic / Buna-n S 1
C2 3718-001-1 SEAL Tungsten Carbide / Buna-n C Optional
F1 19109A080 NUT – HEX SST 3/4 4
F2 15175-300-1 BAIL – LIFTING 1
F3 05454A030 WASHER – LOCK 3/4 4
F4 05454A027 WASHER – LOCK 5/8 2
F5 15174-000-1 BRACKET – MOUNTING 2
F6 19105A033 SCREW – CAP HEX SST 5/8 2
51700-068-7 Seal Kit S
51700-368-7 Carbide Seal Kit C
-24709110000 Para inic Oil O
ORDERING REPLACE ENT PARTS: Product improvements are made from time to time. The latest part design will be fur nished
as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1)
pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller),
(6) quan ti ty required, and (7) shipping instructions.
Ref. Part Part
No. No. Descriptio Qty. Ref. Part Part No. No. Descriptio Qty.
Motor End
Parts List
Notes: S — Parts in Seal Kit C — Parts in Carbide Seal Kit I — Parts in Impeller Kit R — Parts in Rebuild Kit *Consult Factory
O — Amount of oil required will vary between 8-10.5 gal. depending on stator size, fill to above motor windings.
Wet End
Parts List
Item# Descriptio S4T S8L S12L S8LA
Qty. Qty. Qty.
D1 SCREW – MACH. FL. HD. 829-009-1 (4) 07597A021 (4) --- 07597A021 (4)
D2 WASHER – IMPELLER 1945-001-3 1945-001-3 1945-001-3 1945-001-3
D3 SCREW – CAP (HEX SOC.) 3/4 3879-002-1 3879-002-1 3879-002-1 3879-002-1
D4 VOLUTE 13688-000-2 7394-200-2 25457F200 7394-000-2
D5 RING – WEAR 13695-000-3 8345-000-2 24548D000 13535-000-3
D6 CLAMP – WEAR RING --- --- --- 13536-000-3
D7 BELL – SUCTION --- --- 10587-100-2 ---
D8 STAND – PUMP --- --- 10627-000-5 ---
D9 SCREW – CAP HEX SST 1/2-13 --- --- 19106A017 ---
D10 SCREW – CAP HEX SST 1/2-13 --- --- 06106A019 (3) ---
D11 SCREW – CAP SKT HD 1/4-20 --- --- 19103A052 (8) ---
For use with product bui t with USEM motor.
For use with product bui t with USEM motor.

11
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 HP VOLTAGE/ SPRING – CONNECTOR– CONNECTOR – CONNECTOR – INSULATOR CONNECTOR – RING – BOX – ROTOR/ STATOR CONNECTOR –
PH/RPM BEARING WIRE SPLIT BOLT WIRE BUTT SPACER CONNECTION SHAFT SPLICE
15–20 200/3/870 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 8790-000-1 (3) 8662-012-1 13769-003-5 14163-012-5 14163-203-1 15155-004-1 (9)
15–20 230/3/870 64-005-1 (2) 2494-000-1 (1) 2498-005-1 (3) --- 8675-000-1 (3) 1006-001-1 (9) 8662-012-1 13769-006-5 14163-012-5 14163-003-1 ---
15–20 460/3/870 64-005-1 (2) --- --- 2494-000-1 (6) --- 23394A003 (9) 8662-012-1 13769-007-5 14163-012-5 14163-003-1 ---
15–20 575/3/870 64-005-1 (2) --- --- 2494-000-1 (3) --- 23394A003 (3) 8662-012-1 13769-004-5 14163-012-5 14163-603-1 ---
25 200/3/870 64-005-1 (2) --- 2498-007-1 (3) 8675-000-1 (3) 8790-000-1 (3) 8662-009-1 13769-002-5 14162-012-5 14162-203-1 ---
25 230/3/870 64-005-1 (2) 2494-000-1 (1) 2498-007-1 (3) 8675-000-1 (3) 23394A002 (9) 8662-009-1 13769-005-5 14162-012-5 14162-003-1 ---
25 460/3/870 64-005-1 (2) --- --- 2494-000-1 (6) --- 11666-000-1 (9) 8662-009-1 13769-007-5 14162-012-5 14162-003-1 15155-004-1 (9)
25 575/3/870 64-005-1 (2) --- --- 2494-000-1 (3) --- 23394A003 (3) 8662-009-1 13769-004-5 14162-012-5 14162-603-1 ---
30 200/3/870 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 11667-000-1 (3) 8662-009-1 13769-001-5 14162-012-5 14162-203-1 ---
30 230/3/870 64-005-1 (2) 2494-000-1 (1) 2498-007-1 (3) --- 8675-000-1 (3) 23394A002 (9) 8662-009-1 13769-005-5 14162-012-5 14162-003-1 ---
30 460/3/870 64-005-1 (2) 2494-000-1 (4) 2498-005-1 (3) --- 8675-002-1 (3) 11666-000-1 (3) 8662-009-1 13769-007-5 14162-012-5 14162-003-1 15155-001-1 (9)
30 575/3/870 64-005-1 (2) --- --- 2494-000-1 (3) --- 23394A003 (3) 8662-009-1 13769-004-5 14162-012-5 14162-603-1 ---
30 200/3/1150 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 8675-000-1 (3) 8662-011-1 13769-001-5 14161-012-5 14161-203-1 ---
30 230/3/1150 64-005-1 (2) 2494-000-1 (1) 2498-007-1 (3) --- 8675-000-1 (3) 8790-000-1 (9) 8662-011-1 13769-005-5 14161-012-5 14161-003-1 ---
30 460/3/1150 64-005-1 (2) 2494-000-1 (3) 2498-005-1 (3) --- 8675-002-1 (3) 8790-000-1 (9) 8662-011-1 13769-006-5 14161-012-5 14161-003-1 15155-004-1 (9)
30 575/3/1150 64-005-1 (2) --- --- 2494-000-1 (3) --- 23394A001 (3) 8662-011-1 13769-003-5 14161-012-5 14161-603-1 ---
40 200/3/1150 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 11668-000-1 (3) 8662-011-1 13769-001-5 14161-012-5 14161-203-1 ---
40 230/3/1150 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 11667-000-1 (9) 8662-011-1 13769-001-5 14161-012-5 14161-003-1 ---
40 460/3/1150 64-005-1 (2) 2494-000-1 (3) 2498-005-1 (3) --- 8675-000-1 (3) 8790-000-1 (9) 8662-011-1 13769-006-5 14161-012-5 14161-003-1 15155-004-1 (9)
40 575/3/1150 64-005-1 (2) --- 2498-005-1 (3) --- 8675-002-1 (3) 23394A001 (3) 8662-011-1 13769-003-5 14161-012-5 14161-603-1 ---
50 230/3/1150 64-005-1 (2) --- 2498-009-1 (3) --- 8675-000-1 (3) 11667-000-1 (9) 8662-004-1 13769-001-5 14160-012-5 14160-003-1 ---
50 460/3/1150 64-005-1 (2) 2494-000-1 (3) 2498-007-1 (3) --- 8675-000-1 (3) 8790-000-1 (9) 8662-004-1 13769-005-5 14160-012-5 14160-003-1 ---
50 575/3/1150 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 23394A001 (3) 8662-004-1 13769-003-5 14160-012-5 14160-603-1 ---
60 460/3/1150 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 8790-000-1 (9) 8662-003-1 13769-002-5 14159-012-5 14159-003-1 ---
60 575/3/1150 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 23394A002 (3) 8662-003-1 13769-002-5 14159-012-5 14159-603-1 ---
75 460/3/1150 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 11667-000-1 (9) 8662-003-1 13769-001-5 14159-012-5 14159-003-1 ---
75 575/3/1150 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 23394A002 (3) 8662-003-1 13769-002-5 14159-012-5 14159-603-1 ---
50 460/3/1750 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 8790-000-1 (3) 8662-003-1 13769-002-5 14157-012-5 14158-003-1 ---
50 575/3/1750 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 23394A002 (3) 8662-003-1 13769-003-5 14157-012-5 14158-603-1 ---
60 460/3/1750 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 8790-000-1 (3) 8662-003-1 13769-002-5 14157-012-5 14158-603-1 ---
60 575/3/1750 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 8790-000-1 (3) 8662-003-1 13769-002-5 14157-012-5 14158-603-1 ---
75 460/3/1750 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 11667-000-1 (3) 8662-003-1 13769-001-5 14157-012-5 14158-603-1 ---
75 575/3/1750 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 11667-000-1 (3) 8662-003-1 13769-002-5 14157-012-5 14158-603-1 ---
100 460/3/1750 64-005-1 (2) --- 2498-008-1 (3) --- 8675-000-1 (3) 11668-000-1 (3) 8662-003-1 13769-001-5 14157-012-5 14157-003-1 ---
100 575/3/1750 64-005-1 (2) --- 2498-007-1 (3) --- 8675-000-1 (3) 11667-000-1 (3) 8662-003-1 13769-001-5 14157-012-5 14157-603-1 ---
125 460/3/1750 64-005-1 (3) --- 2498-009-1 (3) --- 8675-000-1 (3) 11668-000-1 (3) --- 13769-001-5 14156-012-5 14156-003-1 ---
125 575/3/1750 64-005-1 (3) --- 2498-009-1 (3) --- 8675-000-1 (3) 11668-000-1 (3) --- 13769-001-5 14156-012-5 14156-603-1 ---
150 460/3/1750 64-005-1 (3) --- 2498-009-1 (3) --- 8675-000-1 (3) 11668-000-1 (3) --- 13769-008-5 14156-012-5 14156-003-1 ---
150 575/3/1750 64-005-1 (3) --- 2498-009-1 (3) --- 8675-000-1 (3) 11668-000-1 (3) --- 13769-001-5 14156-012-5 14156-603-1 ---
ORDERING REPLACE ENT PARTS: Product improvements are made from time to time. The latest part design will be fur nished
as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1)
pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller),
(6) quan ti ty required, and (7) shipping instructions.
Motor End
Parts List
For use with product bui t with USEM motor.

12
Cord Cap and
Impe er Parts List
1750 RPM
S8L7500M4-4 75 460/3 2-4 12.12 x 11.12 25252D559 13766-037-5
S8L7500M5-4 75 575/3 2-4 12.12 x 11.12 25252D559 13766-037-5
S8L10000M4-4 100 460/3 1/0-4 13.00 x 12.00 25252D558 13766-036-5
S8L10000M5-4 100 575/3 1/0-4 13.00 x 12.00 25252D558 13766-036-5
S8L12500M4-4 125 460/3 4/0-3 13.75 x 12.75 25252D556 13766-032-5
S8L12500M5-4 125 275/3 4/0-3 13.75 x 12.75 25252D556 13766-032-5
S8L15000M4-4 150 460/3 4/0-3 15.00 x 14.00 25252D551 13766-032-5
S8L15000M5-4 150 575/3 4/0-3 15.00 x 14.00 25252D551 13766-032-5
1150 RPM
S8L3000M6-6 30 200/3 1/0-4 13.00 x 12.00 25252D558 13766-036-5
S8L3000M3-6 30 230/3 2-4 13.00 x 12.00 25252D558 13766-037-5
S8L3000M4-6 30 460/3 4-4 13.00 x 12.00 25252D558 13766-038-5
S8L3000M5-6 30 575/3 6-4 13.00 x 12.00 25252D558 13766-039-5
S8L40000M6-6 40 200/3 1/0-4 14.25 x 13.25 25252D553 13766-036-5
S8L40000M3-6 40 230/3 1/0-4 14.25 x 13.25 25252D553 13766-036-5
S8L40000M4-6 40 460/3 2-4 14.25 x 13.25 25252D553 13766-037-5
S8L40000M5-6 40 575/3 4-4 14.25 x 13.25 25252D553 13766-038-5
S8L50000M3-6 50 230/3 4/0-3 15.00 x 15.00 25252D551 13766-032-5
S8L50000M4-6 50 460/3 2-4 15.00 x 15.00 25252D551 13766-037-5
S8L50000M5-6 50 575/3 2-4 15.00 x 15.00 25252D551 13766-037-5
S8L60000M4-6 60 460/3 2-4 15.00 x 15.00 25252D550 13766-037-5
S8L60000M5-6 60 575/3 2-4 15.00 x 15.00 25252D550 13766-037-5
870 RPM
S8L1500M6-8 15 200/3 2-4 13.38 x 12.38 25252D557 13766-037-5
S8L1500M3-8 15 230/3 4-4 13.38 x 12.38 25252D557 13766-038-5
S8L1500M4-8 15 460/3 6-4 13.38 x 12.38 25252D557 13766-039-5
S8L1500M5-8 15 575/3 10-4 13.38 x 12.38 25252D557 13766-033-5
S8L2000M6-8 20 200/3 2-4 14.85 x 13.85 25252D552 13766-037-5
S8L2000M3-8 20 230/3 2-4 14.85 x 13.85 25252D552 13766-037-5
S8L2000M4-8 20 460/3 6-4 14.85 x 13.85 25252D552 13766-039-5
S8L2000M5-8 20 575/3 8-4 14.85 x 13.85 25252D552 13766-034-5
S8L2500M6-8 25 200/3 2-4 15.00 x 14.00 25252D550 13766-037-5
S8L2500M3-8 25 230/3 2-4 15.00 x 14.00 25252D550 13766-037-5
S8L2500M4-8 25 460/3 6-4 15.00 x 14.00 25252D550 13766-039-5
S8L2500M5-8 25 575/3 8-4 15.00 x 14.00 25252D550 13766-034-5
S8L3000M6-8 30 200/3 2-4 15.00 x 14.00 25252D550 13766-037-5
S8L3000M3-8 30 230/3 2-4 15.00 x 14.00 25252D550 13766-037-5
S8L3000M4-8 30 460/3 4-4 15.00 x 14.00 25252D550 13766-038-5
S8L3000M5-8 30 575/3 6-4 15.00 x 14.00 25252D550 13766-039-5
1750 RPM
S4T5000M4-4 50 460/3 2-4 12 13532-113-2 13766-037-5
S4T5000M5-4 50 575/3 2-4 12 13532-113-2 13766-037-5
S4T6000M4-4 60 460/3 2-4 12.5 13532-111-2 13766-037-5
S4T6000M5-4 60 575/3 2-4 12.5 13532-111-2 13766-037-5
S4T7500M4-4 75 460/3 2-4 13 13532-109-2 13766-037-5
S4T7500M5-4 75 575/3 2-4 13 13532-109-2 13766-037-5
S4T10000M4-4 100 460/3 1/0-4 14 13532-105-2 13766-036-5
S4T10000M5-4 100 575/3 1/0-4 14 13532-105-2 13766-036-5
S4T12500M4-4 125 460/3 4/0-3 15 13532-101-2 13766-032-5
S4T12500M5-4 125 575/3 4/0-3 15 13532-101-2 13766-032-5
S4T15000M4-4 150 460/3 4/0-3 15.13 13532-126-2 13766-032-5
S4T15000M5-4 150 575/3 4/0-3 15.13 13532-126-2 13766-032-5
1750 RPM
S8LA7500M4-4 75 460/3 2-4 13 13532-005-2 13766-037-5
S8LA7500M5-4 75 575/3 2-4 13 13532-005-2 13766-037-5
S8LA10000M4-4 100 460/3 1/0-4 14 13532-001-2 13766-036-5
S8LA10000M5-4 100 575/3 1/0-4 14 13532-001-2 13766-036-5
S8LA12500M4-4 125 460/3 4/0-3 14.5 13532-008-2 13766-032-5
S8LA12500M5-4 125 575/3 4/0-3 14.5 13532-008-2 13766-032-5
1750 RPM
S12L7500M4-4 75 460/3 2-4 11 x 10 25456E562 13766-037-5
S12L7500M5-4 75 575/3 2-4 11 x 10 25456E562 13766-037-5
S12L10000M4-4 100 460/3 1/0-4 11.5 x 11 25456E563 13766-036-5
S12L10000M5-4 100 575/3 1/0-4 11.5 x 11 25456E563 13766-036-5
S12L12500M4-4 125 460/3 4/0-3 12.5 x 11 25456E564 13766-032-5
S12L12500M5-4 125 275/3 4/0-3 12.5 x 11 25456E564 13766-032-5
S12L15000M4-4 150 460/3 4/0-3 13 x 11 25456E565 13766-032-5
S12L15000M5-4 150 575/3 4/0-3 13 x 11 25456E565 13766-032-5
1150 RPM
S12L40000M3-6 40 230/3 1/0-4 12.31 25456E560 13766-036-5
S12L40000M4-6 40 460/3 2-4 12.31 25456E560 13766-037-5
S12L40000M5-6 40 575/3 4-4 12.31 25456E560 13766-038-5
S12L50000M3-6 50 230/3 4/0-3 13.06 25456E560 13766-032-5
S12L50000M4-6 50 460/3 2-4 13.06 25456E555 13766-037-5
S12L50000M5-6 50 575/3 2-4 13.06 25456E555 13766-037-5
S12L60000M4-6 60 460/3 2-4 13.63 25456E553 13766-037-5
S12L60000M5-6 60 575/3 2-4 13.63 25456E553 13766-037-5
S12L75000M4-6 75 460/3 1/0-4 14 25456E552 13766-036-5
S12L75000M5-6 75 575/3 2-4 14 25456E552 13766-037-5
870 RPM
S12L1500M6-8 15 200/3 2-4 12.25 25456E561 13766-037-5
S12L1500M3-8 15 230/3 4-4 12.25 25456E561 13766-038-5
S12L1500M4-8 15 460/3 6-4 12.25 25456E561 13766-039-5
S12L1500M5-8 15 575/3 10-4 12.25 25456E561 13766-033-5
S12L2000M6-8 20 200/3 2-4 13 25456E556 13766-037-5
S12L2000M3-8 20 230/3 2-4 13 25456E556 13766-037-5
S12L2000M4-8 20 460/3 6-4 13 25456E556 13766-039-5
S12L2000M5-8 20 575/3 8-4 13 25456E556 13766-034-5
S12L2500M6-8 25 200/3 2-4 13.5 25456E554 13766-037-5
S12L2500M3-8 25 230/3 2-4 13.5 25456E554 13766-037-5
S12L2500M4-8 25 460/3 6-4 13.5 25456E554 13766-039-5
S12L2500M5-8 25 575/3 8-4 13.5 25456E554 13766-034-5
S12L3000M6-8 30 200/3 2-4 14 25456E552 13766-037-5
S12L3000M3-8 30 230/3 2-4 14 25456E552 13766-037-5
S12L3000M4-8 30 460/3 4-4 14 25456E552 13766-038-5
S12L3000M5-8 30 575/3 6-4 14 25456E552 13766-039-5
Descriptio HP Volt/Ph Cord Trim ITEM #1 ITEM #2
Impeller Cord Cap
Descriptio HP Volt/Ph Cord Trim ITEM #1 ITEM #2
Impeller Cord Cap
For use with product bui t with USEM motor.

13
Pump
Notes
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________
______________________________________________

– Your Authorized Local Distributor –
www.hydromatic.com
STANDARD LIMITED WARRANTY
HYDROMATIC®
warrants its products against defects in material and workmanship for a period of 12 months
from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first -
provided that such products are used compliance with the requirements of the Hydromatic catalog and
technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive free
non-corrosive liquids.
During the warranty period and subject to the conditions set forth, Hydromatic, at its discretion, will repair or
replace to the original user, the parts which prove defective in materials and workmanship. Hydromatic
reserves the right to change or improve its products or any portions thereof without being obligated to provide
such a change or improvement for prior sold and/or shipped units.
Start-up reports and electrical schematics may be required to support warranty claims. Warranty is
effective only if Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be
hooked up, functional and monitored or this warranty will be void. Hydromatic will only cover the lower seal
and labor thereof for all dual seal pumps. Under no circumstance will Hydromatic be responsible for the cost
of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from
the factory or an authorized Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly
install, operate or maintain the unit in accordance with the printed instructions provided; (b) to failures resulting
from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such
service; (d) to units which are not installed in accordance with applicable local codes, ordinances and good
trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for purposes other
than for what it is designed and manufactured; (g) to any unit which has been repaired or altered by anyone
other than Hydromaticor an authorized Hydromatic service provider; (h) to any unit which has been repaired
using non factory specified/OEM parts.
Warranty Exclusions: HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.
Liability Limitation: IN NO EVENT SHALL HYDROMATIC BE LIABLE OR RESPONSIBLE FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER
TO ANY HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE
MAY RESULT FROM IMPROPER INSTALLATION. HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING
LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. HYDROMATIC RECOMMENDS
INSTALLATION BY PROFESSIONALS.
Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of
incidental or consequential damages and therefore such limitations may not apply to you. No warranties
or representations at any time made by any representatives of Hydromatic shall vary or expand the
provision hereof.
USA
740 East 9th Street, Ashland, Ohio 44805
Tel: [phone] Fax: [phone]
CANADA
269 Trillium Drive, Kitchener, Ontario, Canada N2G 4W5
Tel: [phone] Fax: [phone]
Warranty Rev 02/09

START-UP REPORT
cut along dotted line
Distributor:__________________________________________________ Order No.: _________________________
Installing Contractor: _________________________________________ Phone: ____________________________
Sales Contact: ______________________________________________ Phone: ____________________________
Customer: ______________________________________________________________________________________
Location: _______________________________________________________________________________________
1. SYSTEM INFORMATION
Size of Wet Well:_______________________________________Manufacturer: _____________________________
Discharge from Bottom of Basin: ________________________Discharge Location:________________________
Inlet from Bottom of Basin: _____________________________Inlet Location: _____________________________
Type of Check Valves: __________________________________Type of Piping: ____________________________
Does System Have Suction Gauges? TYes TNo Suction Pressure Reading: __________________
Does System Have Discharge Gauges? TYes TNo Discharge Pressure Reading:________________
Liquid Being Pumped:_______________________Temperature (F°): __________ Pct. of Solid (%):___________
Is a Sketch or Photograph of System Available? TYes TNo If So, Please Attach.
Any Additional Comments on System:______________________________________________________________
_______________________________________________________________________________________________
2. ELECTRICAL INFORMATION
Control Panel Part Number: _____________________________Panel Rated Amps: ________________________
Manufacturer: _________________________________________Voltage: _______________ Phase: ____________
Heater Size:___________________________________________Location of Panel to Wet Well: _______________
Incoming Line Voltage: _________________________________Actual? ___________________________________
Voltage to Pumps: _____________________________________Actual? ___________________________________
Type of Junction Box: __________________________________Manufacturer of Junction Box: ______________
Are Floats Installed in Wet Well? TYes TNo Are Floats Set to Engineer’s Specs? TYes TNo
Are Floats Wired for Proper Sequencing? TYes TNo Are Heat Sensors Hooked Up? TYes TNo
Is the Seal Leak Detection Hooked Up? TYes TNo
Any Additional Comments on Electrical: ____________________________________________________________
_______________________________________________________________________________________________
3. PUMP INFORMATION
Type of Pump:_________________________________________Serial Number of Pump: ____________________
Voltage of Pump: ________________ Phase: _______________RPM: _________________ Amps: ____________
Impeller Size:____________________ C.O.S. TDH: __________GPM: _________________
Voltage Supplied from Panel:____________________________Actual? ___________________________________
Actual Amperage (All Phases): Phase 1 Amps: ________ Phase 2 Amps: ________ Phase 3 Amps: ________
Define the Rotation of the Pump: TClockwise TCounterclockwise
Method Used to Check Rotation: TViewed from the Top TViewed from the Bottom
Any Additional Comments on Pumps: ______________________________________________________________
_______________________________________________________________________________________________
4. ACKNOWLEDGE
Acknowledge that all information is accurate and proper procedures have been followed.
Customer: ___________________________________________________________________ Date: _____________
Start-up Technician:___________________________________________________________ Date: _____________
Send to Warranty Manager, 1101 Myers Parkway, Ashland, OH 44805
or Fax to 419-207-3344
or email to [email protected]
or submit online at http://forms.pentairliterature.com/startupform/startupform.asp?type=h