WIRING REQUIREMENTS
Fig.1
The unit requires connection to a 230 AC 50Hz mains electricity supply.
It is recommended that the unit is connected to the domestic lighting circuit via a
5 amp fused spur and using 2-core round flexible cable of at least 1mm2gauge
(waterproof cable should be used for outdoor installations).
It is also advisable to install a single pole wall switch to allow easy control of the
floodlight (Fig. 1).
IMPORTANT OPERATION & MAINTENANCE INSTRUCTIONS
The Hylite Mightylite floodlight a low energy, high powered outdoor LED floodlight which is suitable for installation on solid
walls in a range of locations including entrances, gardens, staircases, garages and outdoor parking areas
The unit requires connection to a 230 AC 50Hz mains electricity supply.
IMPORTANT SAFETY INSTRUCTIONS
HYLITE MIGHTYLITE – INSTALLATION AND OPERATING INSTRUCTIONS
DO NOT position the light near flammable or combustible materials (such as wood, cloth, paper) or near flammable,
combustible or explosive liquids, solids, gases or equipment.
DO NOT direct the light into a person’s eyes. This light has a very intensive light output, which if incorrectly used could
cause eye damage.
ALWAYS disconnect the mains power supply before servicing or performing any maintenance.
ALWAYS maintain the light in good condition, with repairs only undertaken by a qualified electrician
ONLY carry out repairs using genuine parts. Non-authorized parts may be dangerous and will invalidate the warranty
WARNING: THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN, AND CHECKED TO ENSURE IT IS SAFE BEFORE USING
PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL AND OPERATE THIS LIGHT
The risk of electric shock should be minimized by the installation of appropriate safety devices including the
incorporation of an RCCB (Residual Current Circuit Breaker) into the main distribution board.
DO NOT wire this floodlight directly into the lighting circuit. Use a switched fused spur. Cables should always be
protected against short circuit and overload by use of an RCD.
Ensure the voltage marked on the product is the same as the electrical power supply to be used.
DO NOT install the light where it is likely to be knocked or hit; in hot or humid conditions such as bathrooms, shower
rooms or saunas; or near an exhaust outlet e.g. boiler flue, dryer outlet.
TOOLS REQUIRED
Electric/hand-held drill
No.8 masonry drill bit
Electricians screwdriver
Large cross-head screwdriver
Small cross-head screwdriver
Wire cutters
THIS PRODUCT IS SUITABLE FOR WALL MOUNTING ONLY
PARTS INCLUDED
1 x Mightylite LED Floodlight
1 x Connection box
1 x Cable gland
4 x Connection box screws
4 x Connection box screw covers
4 x Connection box fixing screws
4 x Connection box fixing screw covers
Fig.2
FUSE
3 AMP FUSE
TO LAMP
FROM MAINS
SUPPLY
DOUBLE-POLE SWITCHED FUSED SPUR
F
1
2
5
4
3
T R
PIR
sensor
More sensitiveLess sensitive
L
N
SL
E
Override switch
Live
C L1
Neutral Earth
To Mains MightyLite
N In N Out
L In L Out
3-5m
Fig.5
Fig.4
Fig.3
Landscape
Portrait
FIXING THE CONNECTION BOX
WARNING: Isolate the power supply before installation.
• Position the unit on the wall and mark the position for the connection box
(which can be positioned in either landscape or portrait planes [Fig. 3]).
• Ensure the wires can easily enter the connection box through either one of the
knock-outs on the side of the connection box, or through the knock-out at the
rear of the box.
NOTE: It is recommended that the knock-outs on the sides of the
connection box are used in conjunction with the cable gland [Fig 4.] as
using the knock-out at the rear of the connection box will reduce the
weatherproof rating of the unit to IP23.
• However, If feeding a wire(s) through the knock-out at the rear of the connection
box, this will need to be removed, the sealing grommet fitted [Fig.5] and the
wire pushed through into the connection box BEFORE it is secured to the wall.
• If feeding a wire(s) through the side knock-outs, it is easiest to fit the cable
gland to the connection box [Fig.4] BEFORE securing it to the wall, and wires
should enter the connection box from the sides or underneath, NOT from the top.
CHOOSING A MOUNTING LOCATION
INSTALLATION INSTRUCTIONS
• Mount the floodlight onto solid brick or woodwork, 3 - 5m above the ground
[Fig. 2]
• Avoid positioning the light near heat sources such as hot ventilator ducts, air
conditioning units, street lighting or traffic which may interfere with its operation.
TO MAINS MIGHTYLITE
Earth
L in L out
N in N out
