Hyperion EOS 0606i AC/DC User manual

HYPERION EOS 0606i AC/DC
EOS0606I-AD USER’S MANUAL
EOS 0606i AC/DC Special Features
*Two INPUT power choices:
Use AC 100V~240V at home OR DC 11V~15V anywhere
*Powerful, yet compact and portable with wide support for battery types
*Integrated Hyperion LBA Balancer for LiPo (3.7v) and LiFe (3.3v) based cells
*Balance Multi-Adapter for 2S to 6S packs included
*Charge and Discharge Modes (and Cycling for NiMh and NiCd)
*Clear and easy-to-read LCD Screen with Warnings common setup errors
*Packaged in a rugged aluminum case - Long Input leads
*Hyperion Balance Multi-Connector Included. Option multi-connectors
for
most common brands are also available (see details end of document)
Specifications
Input voltage range 11.0-15.0V DC OR 100~240V AC at 50~60 Hz
Only ONE source may be connected at a time!
1-14 NiCd – Nickel-Cadmium cells
1-14 NiMH – Nickel-Metal Hydride cells
1-6 LiPo – Lithium Polymer cells, 100~6000mAh (3.7V/cell type only)
1-6 LiFe – Lithium Iron (3.3V/cell types, inc. A123 brand cells / LiFePO4 cells)
Appropriate battery types and
range of series-connected cells
1-6 Lead-Acid cells (2V per cell nominal)
Charge current 0.1A ~ 6.0A MAX, by 100mA steps (50W limit)
Discharge current 0.1A ~ 1.0A MAX, by 10mA steps (5W limit)
Trickle charge current (NiCd, NiMH) 0 ~ 200mA
“Delta V” peak detection for NiCd/NiMH
Charge termination “CV/CC” for Lithium and Lead-Acid Batteries
Cycling Modes (NiCd, NiMH) Charge>Discharge or Discharge>Charge
Display type 2-line, 16 character blue backlit LCD
Safety precautions
•KEEP CHARGER AWAY FROM CHILDREN AND PETS AT ALL TIMES!
•This charger is ONLY for NiCd/NiMH, Lithium (3.7V/cell), A123 (3.3V/cell), and Lead-Acid (2.0V/cell)
type cells. DO NOT connect others, such as 3.6V/cell Lithium-Ion, or non-rechargeable batteries!
•Always place the charger on a firm, level, and fireproof surface for charging
•Do not place the battery or charger on or near flammable materials while in use:
Keep away from carpets, cluttered workbenches, etc
•Do not exceed cell manufacturer’s suggested max charge rates
•Do not use automotive type battery chargers to power the charger
•Do not leave the charger unattended while charging
•Do not allow water, moisture or foreign objects into the charger
•Do not open the charger, nor attempt any repair as it is dangerous and will void your warranty
•Do not obstruct the air intake holes on the charger
•ALWAYS follow correct connection sequence, as given below
•CAREFULLY FOLLOW THE BATTERY PACK MAKER’S RECOMMENDATIONS AND SAFETY ADVICE!
Initial Setup
The EOS 0606i requires 4mm Bullet Connectors (aka Banana Plugs) on 12awg wire leads for output harness between charger
and battery main wires. Harness wire leads should never exceed 20cm in length. Pre-assembled output harnesses are
available under Hyperion Part #HP-EOSOUTCORD. Solder your chosen battery-side connector to the bare wire ends of the
harness, taking great care to observe proper polarity.
If, after carefully reading the following pages on usage, you have any difficulty using the charger please refer to the final
pages for troubleshooting guide and warranty terms. It is well to carefully check your charger before making a return, as
problems in setup, cabling, or power supply are much more common than defects in the charger. Chargers returned by the
user and later found not defective will only be returned to the user at the user’s expense and may incur a service charge.

ALWAYS FOLLOW this connection sequence, and reverse sequence to disconnect:
1) Connect OUTPUT harness 4mm plugs to the sockets located on the right side of the charger.
Take care that the Output Harness RED wire bullet connector goes to the (+) socket, and BLACK wire to (-) .
2a) Connect Charger INPUT alligator clips to an appropriate DC power source:
a) A 12V automobile battery
b) A quality, low-noise DC power supply of 12~15V with 5A+ rating (large batteries may require 10A supply)
OR
2b) Connect to AC wall power 100~240V using the supplied AC cable
DO NOT CONNECT BOTH AC AND DC INPUT AT THE SAME TIME!!
The Charger will display INPUT VOLTAGE error message if input voltage is out of range. If this happens, please recheck the input
power supply to make sure correct voltage is present.
3) Set the battery type using the charger configuration buttons.
*The INC and DEC buttons are used to Increase or Decrease
values, such as Charge Current or Cell Count
*The INC and DEC buttons are also used to select MODE, such as Charge, Discharge, or Cycle, and to reach Lithium Type sub menu.
*The BATT TYPE and ENTER buttons both have two modes: SHORT press or LONG (~1 second) press
•Short press BATT TYPE: Scroll battery types
•Long press BATT TYPE: View input/output Data
•Short press ENTER: Scrollsettings for a battery type. Values will blink when selected. Blinking will stop after a few
seconds if you do not make a change.
Short press Enter to re-select a setting to change. Short press BATT TYPE to re-select Battery Type, then INC/DEC to change
values.
•Long press ENTER: START charging (or discharging, or cycling)
Let’s start by using a NiMh battery as an example.
When the charger is first connected to input power, it will display the previously used battery configuration. This is especially
convenient if you often charge the same type of battery.
1) If NiMh is not shown, short push the BATT TYPE button to scroll through all battery types. Stop when you reach NiMh.
2) Short press the ENTER button to select “C”, charge rate in Ampere
3) Press INC or DEC buttons to choose the proper rate for your battery pack.
Charging NiCd and NiMH is mostly automatic, and the setup routines are the same for both. You only need to consult the
documentation for your battery pack (or ask your dealer) to determine the proper charge current in Ampere (A). If the rate is given
in mA, note that 100mA equals 0.1A: so 900mA would be 0.9A, for example.
4) Attach your NiMH battery to the EOS 0606i Output side harness, checking that +/- polarity is correct.
5) Long press ENTER button (hold down for about 1~2 seconds) to begin charging
NO BATTERY error – if battery not connected
OPEN CIRCUIT error – if the battery becomes disconnected from the charger after START
REVERSE POLARITY error – if the battery is connected in reverse
In
setting. However, if you want to enter DISCHARGE or CYCLE modes, you can press the BATT TYPE button to start NiMH
blinking, then press INC/DEC buttons to scroll through the various modes. Once the mode is settled (like CYCLE), short
press ENTER to start values blinking for editing.
our NiMH charging example above, we pressed the ENTER button when “NiMH” was blinking, to go directly to charge rate
hanging Between Lithium Types (LiPo vs LiFe) sub menu. Start by pressing BATT TYPE once,
henever Lithium battery charging is started with Balancer properly connected, the display will show:
. NOT CONNECTED, stop and check your connections carefully, and repair as needed. We
ote: The EOS0606i-AD does not support charging of legacy 3.6v Lithium Ion cell types.
C
Switching between LITHIUM battery types is done in a
then INC button twice. At the Lithium TYPE screen, press ENTER, then INC/DEC to select type.
Finally, press DEC to return to Discharge or Charge Screens
W
BALANCER CONN. CONNECTED.
If you see instead BALANCER CONN
strongly recommend lithium balance charging at all times.
N
Never attempt to charge these cells, under any circumstances, using this charger.
LiPo CHARGE
C=6000mAh 6S LiPo DISCHARGE
D=1.00 A 6S
INC
DEC
INC
Lithium Type
LiPo
INC ENTER Lithium Type
LiPo
DEC
Lithium Type
LiFe
ENTER
Lithium Type
LiFe
LiFe CHARGE 6S LiFe DISCHARGE
C=6000mAh D=1.00 A 6S

LiPo CHARGE
C=6000mAh 6S
LiPo CHARGE
C=6000mAh 6S
LiPo DISCHARGE
D=1.00 A 6SS
OLYMER/ION MODE (for 3.7V/cell types only!)
etting LiPo battery capacity ery capacity from 100mAh to 6000mAh with INC & DEC buttons
t
etting Battery Voltage / Number of Cells in Series for LiPo battery packs
cell count e.g. ‘6S’
OTE: The EOS Series chargers have intelligent detection routines to help you avoid making
etting discharge parameters rrent from 0.10A to 1.00A (0.01A per step) with INC & DEC button.
iFe MODE [LiFePO4, A123]
he LiFe charge/discharge modes are intended for cells with 3.3V nominal, with Lithium Phosphate chemistry. The LiFe
ue to the nature of A123/LiFePO4 cells (wide divergence in cell voltages during charging) and due to the high rates at which
Number of LiPo Cells Wired in Series (Pack Voltage)
OLYMER/ION MODE (for 3.7V/cell types only!)
etting LiPo battery capacity ery capacity from 100mAh to 6000mAh with INC & DEC buttons
t
etting Battery Voltage / Number of Cells in Series for LiPo battery packs
cell count e.g. ‘6S’
OTE: The EOS Series chargers have intelligent detection routines to help you avoid making
etting discharge parameters rrent from 0.10A to 1.00A (0.01A per step) with INC & DEC button.
iFe MODE [LiFePO4, A123]
he LiFe charge/discharge modes are intended for cells with 3.3V nominal, with Lithium Phosphate chemistry. The LiFe
ue to the nature of A123/LiFePO4 cells (wide divergence in cell voltages during charging) and due to the high rates at which
Number of LiPo Cells Wired in Series (Pack Voltage)
LITHIUM PLITHIUM P
SS
Adjust and set the desired battAdjust and set the desired batt
(50mAh per step). Press the ENTER button to confirm setting. Charge rate is set on the basis of
selected capacity, at 1C rate. Example: Li-Po cell of 1500mAh capacity: 1C = 1500mAh (= 1.5A).
If your battery is larger than 6000mAh, you can charge it at the 6000mAh setting, but it will jus
(50mAh per step). Press the ENTER button to confirm setting. Charge rate is set on the basis of
selected capacity, at 1C rate. Example: Li-Po cell of 1500mAh capacity: 1C = 1500mAh (= 1.5A).
If your battery is larger than 6000mAh, you can charge it at the 6000mAh setting, but it will jus
take longer to finish charging. take longer to finish charging.
SS
Select the total battery voltage to be charged with ENTER, INC & DEC buttons.Select the total battery voltage to be charged with ENTER, INC & DEC buttons.
The charger knows the pack’s voltage both from the balancer connector and theThe charger knows the pack’s voltage both from the balancer connector and the
NN
mistakes, and LOW or HIGH VOLTAGE errors are displayed if battery voltage does not match your
setting. HOWEVER, under some circumstances, especially with over-discharged or damaged
batteries, the safeguard could fail. Therefore, be absolutely sure that you have correctly set pack
voltage correctly before charging, every time! Using LBA cell balancer with EOS Charger is
STRONGLY recommended, as it greatly increases safety.
mistakes, and LOW or HIGH VOLTAGE errors are displayed if battery voltage does not match your
setting. HOWEVER, under some circumstances, especially with over-discharged or damaged
batteries, the safeguard could fail. Therefore, be absolutely sure that you have correctly set pack
voltage correctly before charging, every time! Using LBA cell balancer with EOS Charger is
STRONGLY recommended, as it greatly increases safety.
SS
Adjust to the desired discharge cuAdjust to the desired discharge cu
Press the ENTER button to confirm setting. Set pack voltage, 1S~6S as in charging example above.
Autocut occurs automatically at 3.0V per cell.
Press the ENTER button to confirm setting. Set pack voltage, 1S~6S as in charging example above.
Autocut occurs automatically at 3.0V per cell.
LL
T
(LiFePO4 charge/discharge modes are intended for cells with 3.3V nominal produced by A123 Company, or other-brand
LiFePO4 cells which are recognized to be of good quality from well-known makers. Choose LiFe for BATT TYPE, for charging
such cells. The LiFe charge mode MAY work with “no brand” LiFePO4 cells having 3.3V nominal voltage, but Hyperion has
found some “knock off” cells in the market of very questionable quality. Customers who use A123 mode (LiFePO4
mode) to charge such off-brand cells assume all risk. In no case does Hyperion HK Ltd. Accept liability due to the
failure of the cell(s) itself during charging or discharging.
T
(LiFePO4 charge/discharge modes are intended for cells with 3.3V nominal produced by A123 Company, or other-brand
LiFePO4 cells which are recognized to be of good quality from well-known makers. Choose LiFe for BATT TYPE, for charging
such cells. The LiFe charge mode MAY work with “no brand” LiFePO4 cells having 3.3V nominal voltage, but Hyperion has
found some “knock off” cells in the market of very questionable quality. Customers who use A123 mode (LiFePO4
mode) to charge such off-brand cells assume all risk. In no case does Hyperion HK Ltd. Accept liability due to the
failure of the cell(s) itself during charging or discharging.
D
some of these cells – such as A123 brand – can be charged, one MUST ALWAYS properly use the cell balancer function
whenever charging in LiFe Mode; failure to do so will result in poor pack performance at best, and damage to cells at worst.
Customers who charge in LiFe mode without balancer connected assume all risk of charger and battery failure!
D
some of these cells – such as A123 brand – can be charged, one MUST ALWAYS properly use the cell balancer function
whenever charging in LiFe Mode; failure to do so will result in poor pack performance at best, and damage to cells at worst.
Customers who charge in LiFe mode without balancer connected assume all risk of charger and battery failure!
1S 2S
73S 11.1V 4S 14.8V 5S 18.5V 6S 22.2V3.7V .4V
LiPo CHARGE 6S
C=6000mAh LiPo DISCHARGE D=1.00 A 6S
BATT TYPE INC
DEC
LiPo CHARGE
C=6000mAh 6S
LiPo CHARGE
C=6000mAh 6S
BATTERY CHECK
WAIT PLEASE. . . .
CHG 0:00 00000
LP + 2.20A 22.200V
ENTER ENTER
DEC
LiPo DISCHARGE
D=1.00A 6S
LiPo DISCHARGE
D=1.00A 6S
BATTERY CHECK
WAIT PLEASE. . . .
DCH 0:00 00000
LP + 1.00A 22.200V
START
INC INC DEC
ENTER ENTER
INC DEC DEC INC
START
BALANCER CON.
CONNECTED
BATTERY CHECK
WAIT PLEASE. . . .

etting charge current the battery at a 1C rate from the capacity you tell it. It is possible to
etting battery charge voltages for A123/LiFe battery pack his in turn, with the correct
etting discharge current the desired discharge current from 0.10A to 1.00A (0.01A per
NiCd / NiMH MODES (Ni H mode is the same as below, except Mode shows ‘NiMH’)
Cd/NiMH continued next page
Number of LiFe Cells Wired in Series (Pack Voltage)
S
The EOS 0606i will charge
charge at higher than 1C but the user accepts all responsibility.
S
Set the number of cells in series that make up your battery pack. T
cell type, tells the charger the packs voltage. Used with the balancer makes for safer charging.
S
Press Enter to find and adjust
step) with the INC & DEC buttons. Press the ENTER button to confirm the setting.
M
Ni
1S
3.3V 2S 63S 9.9V 4S 13.2V 5S 16.5V 6S 19.8V.6V
NiCd CHARGE 16.8V
C=3.0A
B TYPEATT
ENTER
NiCd DISCHARGE V
D=1.00A 16.8 NiCd CYCLE D->C 5
C=3.0A D=1.00A
NiCd CHARGE
C=3.00A 16.8V
BA Y CHECKTTER
WAIT PLEASE. . . .
START
CHG 0:00 00000
NC + 3.00A 16.800V
NiCd DISCHARGE
D=1.00A 16.8V
NiCd DISCHARGE V
D=1.00A 16.8
BA Y CHECKTTER
WAIT PLEASE. . . .
DCH 0:00 00000
NC - 1.00A 16.800V
NiCd CYCLE D->C 5
C=3.0A D=1.00A
NiCd CYCLE D->C 5
C=3.0A D=1.00A
NiCd CYCLE D->C 5
C=3.0A D=1.00A
NiCd CYCLE D->C 5
C=3.0A D=1.00A
BA Y CHECKTTER
WAIT PLEASE. . . .
DCH 0:00 00000
NC + 3.00 1.200V
NiCd CYCLE C->D 5
C=3.0A D=1.00A
START
START
INC DEC
INC DEC
INC DEC
INC DECINC DEC
INC DEC
INC DEC
INC INC
DEC DEC
DEC
INC
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
LiFe CHARGE 6S
C=6000mAh LiFe DISCHARGE D=1.00 A 6S
BATT TYPE INC
DEC
LiFe CHARGE
C=6000mAh 6S
LiFe CHARGE
C=6000mAh 6S
BATTERY CHECK
WAIT PLEASE . . .
CHG 0:00 00000
LF + 2.50A 19.000V
ENTER ENTER
DEC DECINC INC
LiFe DISCHARGE SD=1.00 A 6
ENTER ENTER
DEC DECINC INC
LiFe DISCHARGE
D=1.00 A 6S
BATTERY CHECK
WAIT PLEASE . . .
START START
DCH 0:00 00000
LF - 1.00A 19.800V
LiFe CHARGE
C=6000mAh 6S
LiFe CHARGE
C=6000mAh 6S
LiFe DISCHARGE
D=1.00 A 6S
BALANCER CON. BALANCER CON.
CONNECTED CONNECTED

Pb CHARGE
C=4.0A 12Vpack
Pb CHARGE
C=6.0A 12Vpack
Pb DISCHARGE
D=1.00A 12Vpack
Setting charge current
Adjust and find the desired charge current .1A to 6.0A with INC & DEC
utton to confirm setting.
g from 0.1A to 1A, with INC & DEC buttons.
confirm setting. Auto-limit may reduce the current limiting the
he charger should stop discharging the battery.
ltages to be discharged from 0.1V to 16.8V with INC &
ge / Discharge to Charge). Set cycling
buttons, and press the ENTER button to confirm setting.
b MODE (lead-acid battery)
Setting charge current
Adjust and find the desired charge current which ranges from 0.1A to 6.0A with INC & DEC buttons.
confirm setting
d Battery
elect the proper total battery voltage to be charged or discharged with INC & DEC buttons – 2V, 4V,
djust and find the desired discharge current from 0.10A to 1.00A (0.01A per step) with INC & DEC
n to confirm setting.
NiCd CHARGE which ranges from 0
C=3.00A 16.8V buttons. Press the ENTER b
Setting discharge current
Adjust and find the desired discharge current, rangin
NiCd DISCHARGE
D=1.00A 16.8V Press the ENTER button to
discharge power to 5W.
Setting discharge cutoff voltage
This is the voltage that t
NiCd DISCHARGE
D=1.00A 16.8V Adjust and find total discharge cutoff vo
DEC buttons. Press the ENTER button to confirm setting.
NiCd CYCLE C->D 5 Setting cycle
This is to set cycling with two options ( Charge to Dischar
C=3.0A D=1.00A
with INC & DEC
P
Press the ENTER button to
Setting total battery voltage for Lead-Aci
S
6V, 8V, 10V, and 12V [2V per cell types only]
Setting discharge current
A
button. Press the ENTER butto
Pb CHARGE
C=4.0A 12Vpack DEC
B TYPEATT INC Pb DISCHARGE
D=1.00A 12Vpack
Pb CHARGE
C=4.0A 12Vpack
Pb CHARGE
C=4.0A 12Vpack
BA Y CHECK
WAIT PLEASE. . . .
TTER
CHG 0:00 00000
Pb + 4.0A 12.000V
Pb DISCHARGE
D=1.00A 12Vpack
ENTER ENTER
Pb DISCHARGE
D=1.00A 12Vpack
BA Y CHECK
WAIT PLEASE. . . .
TTER
CHG 0:00 00000
Pb - 1.0A 12.000V
ENTER
INC INC DECDEC
ENTER
INC DEC INC DEC
START START

Displays during Charge, Discharge, and Cycle and connection. For example, Lithium types when connected to a
Completion Display
When the Enter button is pressed, charge or discharge will be stopped.
e back to the main display, press the Enter button.
Data Display – Keys
TT TYPE during charging or discharging to view the data display menu.
Use INC and DEC to scroll through the data screens.
Pressing BATT TYPE again will return you to the charge/discharge screen.
a Display – Screens (Example: During a Balancer-Connected Lithium Charge)
SHOOTING
e battery you are trying to charge and the settings on the EOS 0606i match. Battery type (such as
) Check that the input cable and output cables: *Are not frayed, worn, cut, or damaged side
) Attach the charger input connectors to a 12V automotive battery that is in good condition and fully charged. Wiggle the
) Try another battery for charging. If your RC battery is in poor condition, over discharged, or in some other way
Note that exact display may depend on type of battery
balancer will alternately show CHG / BLC at top left while charging, and CHG / BLC / END when finished charging. Also note
that after charging the EOS0606i may apply maintenance trickle charge or balance discharge as needed until disconnected.
In order to mov
Press BA
Dat
TROUBLE
(1) Check again that th
NiMH or Lithium), battery capacity, number of cells (charge voltage), and charge rate must all be correct.
(2
*Have proper connectors in good condition
*Are the proper gauge (2.5mm, 14ga or higher) *Are proper length – 20cm (8”) on output
(3
Terminal clips into the battery posts to insure that you have a good connection. Try the AC input if failing while using DC.
(4
CHG 030:25 00000
NC + 3.00A 10 .75V DCH 030:25 00000 NC - 3.00A 10 .750V
END 030:00 00000
NC 100mA 10.75V
INPUT = 12.00V
OUTPUT = 23.50V
CHG: charge e Time in minutes : sec Time Delay in minutes between
DCH: discharg Charging and Discharging or
Discharging and Charging
C→D: cycle
D→C: cycle Capacity in mAh
DELAY TIME
5 : 00
NC: NiCd
/LiFe
NM: NiMH
LP: LiPo
LF: A123
Pb: Lead-Acid
ENTER INC
INPUT = 12.00V
OUTPUT = 23.50V 3.92 3.92 3.92V 3.92 3.91 3.93V LCB-MAX =3.937V LCB-MIN =3.923V
DEC
INC LCB-[01] =3.923V
LCB-[AVG =3.930V
ChgCAPA= 400mAh
DchCAPA = 0mAh
CHG PEAK= 23.62V
DCHG AVR = 0.00V
DEC
INC
DEC
INC
DEC
INC
DEC
ENTER
CHG 0:00 00000
LP + 2.20A 22.200V
CHG 15:00 00500
LP + 2.20A 22.200V

defective the charger may correctly refuse to charge it based on safety algorithms.
(5) Try another RC battery type. For example switch to a NiMH battery if you are failing to charge Lithium types. Success
) Contact your dealer with full details and description of the problem, including the type of input power source, RC battery
RROR MESSAGES
with one type but failure with another generally indicates that the charger is working properly. The failing battery type is
almost certainly in poor condition, then, or you have improperly set the charger for it.
(6
type and cell count, and history of the charger – specifically, has the charger been working properly before, or failing from
new condition?
E
INPUT VOLTAGE ERROR Input voltage is below 11.0V or exceeds 15.0V
NO BATTERY Battery not detected
OUTPUT BATT REVERSE POLARITY Battery is connected in reverse polarity to Output leads
OUTPUT CIRCUIT PROBLEM Non-Specific Circuit error. Check battery condition
CHECK BATT OPEN CIRCUIT Battery disconnected during charging
CHECK BATT OVER VOLTAGE Battery voltage too high to match charger settings
CHECK BATT LOW VOLTAGE Battery voltage too low to match charger settings
BALANCER VOLTAGE TOO HIGH If voltage per cell is too high during balancing, this message may appear.
BALANCER VOLTAGE TOO LOW If cell’s voltage falls too low during balancing, this message may appear
DON’T CHARGE Lixx WITH THIS MODE A Lithium pack is connected by balancer, but NiCd/NiMH/Pb mode is selected for charging
Note: If the incorrect number of cells is selected for a lithium type battery, and charging is begun, the charger may give error
ALANCE MULTI-CONNECTORS for most common lithium pack brands are available from your dealer: #HP-EOSLBA-26xx
P: fit HYPERION, POLYQUEST, PolyQ, ETEC, and some other brand packs.
all FLIGHTPOWER* packs from 2S to 6S.
ch Note*: Due to the wiring arrangement on some Thunderpower and FlightPower 4S packs only, the 4S packs may need
ARRANTY
YPERION Chargers are guaranteed to be free from defects in materials and workmanship for a period of one calendar year
amage due physical shock (dropping on the floor, etc), inappropriate power supply (automotive battery charger, etc!), water,
njoy the Power!
he Hyperion Team
immediately and stop charging. In some cases, however, the charger will begin charging at the (lower) voltage it sees as
correct, and watch all cells to confirm the incorrect setting. For example, if you connect a 3S pack but set the charger for 4S
by mistake, the charger may begin by charging at 3S voltage level, and watch all cells. When the mistake is confirmed, the
charger will give error and terminate. This is normal and correct behavior.
B
Hyperion Balance Multi-Connectors
Applications list below may be subject to change, depending on maker decisions outside our control. If your brand is NOT
listed, email your battery maker to ask them WHICH OF THE BRANDS BELOW they are compatible with.
H
EH: fit KOKAM, GRAUPNER and ROBBE
XH: fit ALIGN and DUALSKY packs
TP: fit recent THUNDERPOWER and
Te
the 6th wire removed in order to function properly with HP-EOSLBA-26TP MultiAdapter for 4S charging.
SEE DIAGRAM at http://media.hyperion.hk/dn/eos/eoslba26/EOSLBA26TP-FP4Smod.gif
W
H
from date of purchase. Your selling dealer is your first point of contact for warranty issues. Return postage costs are the
responsibility of the user in all cases. Submit copy of original receipt with the return.
D
moisture, and humidity are specifically NOT covered by warranty. It is well to carefully check your charger before making a
return, as problems in setup, cabling, or power supply are much more common than defects in the charger.
E
T