HySecurity MX3426 User manual

Installation Instructions
MX3426
StrongArm Flashing Light Kit
•MX3425 LED Light Bulb (24V, AC/DC) for electric asher kits
•MX3426 Light Kit, Flashing, runs on 24VDC
•MX001197 Add-On Light Kit, Flashing runs on 24VDC
NOTE: The Add-ON Light Kit has its own separate set of instructions.
Tools Needed:
• 7/16” socket head wrench
• 3/8” drive rachet
•Flat head screwdriver
•Needle nose pliers
•Wire nuts
DANGER
Turn off power to the Control Box before
installing the Light Kit.
Installation Steps
Review the illustrations and follow
the steps below:
1. Open the package and unwind
the length of cable.
NOTE: Fourteen feet (4.2 m) of cable
accompanies the MX3426 Light Kit.
StrongArm Flashing Light Kit
24VDC N.O. (Normally Open)
Wire connection: Solid state, user relay 3
Installer Menu: Set Relay Logic, RL 3 to “19”
Red Lens
Amber Lens
Barrier Arm
If using the “Add On” kit MX001197, connect wires together in parallel.
Barrier Arm
Fasteners:
Bolt: ¼” x 20 x 1¾”
2 washers
1 lock nut
Loop required
for barrier arm
movement. Allow a
minimum 2 foot (61 cm)
cable slack.
continued...,
CAUTION
Order MX3425 LED replacement bulbs for use in the light kits. DO NOT use incandescent
bulbs. Incandescent bulbs draw a disproportionate amount of amperage and, if used,
voids the Limited Warranty and may damage the equipment.
www.SecureOpeners.com | [phone] | [email protected]

2. Feed the cable through the chassis
and control box. Pop out the
inserts, if need be.
3. Connect the wire ends to +24V
on the power module and N.O.
contact User Relay 3 on the Smart
Touch Controller.
CAUTION
When placing the asher on the arm, be
sure to account for cable slack needed to
allow the arm to fully open.
4. Mount the asher in an
appropriate location. Using the
base as the template, mark and
drill two holes (2⅜” center to
center) in the barrier arm.
5. Use a at head screwdriver to
remove two screws holding the
cover plate.
6. Insert fasteners as shown and
secure the asher base to the
barrier arm.
CAUTION
Avoid crimping the wires inside the base.
7. Replace the cover plate and secure
it using the two screws.
8. Turn the power switch ON and
program user relay 3 through the
Installer Menu.
Set R3 to 19 FLASHER
STOP BUTTON
OPEN BUTTON
CLOSE BUTTON
REMOTE OPEN AND
RADIO CONTROL
OPEN/CLOSE
1
OPEN PARTIAL
INTERLOCK OPEN
TIME CLOCK OPEN
FREE EXIT DETECTOR
DISABLE EXIT DETECTOR
DISABLE CLOSE TIMER
INSIDE OBSTRUCTION
VEHICLE DETECTOR
OUTSIDE OBSTRUCTION
VEHICLE DETECTOR
SHADOW/RESET
VEHICLE DETECTOR
EDGE SENSOR
PHOTO EYE POWER
24 VOLTS COMMON
PHOTO EYE POWER
DO NOT USE
PHOTO EYE
OPEN DIRECTION
DO NOT USE
PHOTO EYE
CLOSE DIRECTION
DO NOT USE
CHARGER
AC LOSS
SPARE INPUT
EMERG CLOSE
FIRE DEPT OPEN
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
Smart Touch Controller
LIMIT DUAL GATE RADIO OPTIONS
DRIVE POWER RS485
MOTOR USER 1 USER 2
USER 3
VEHICLE DETECTORVEHICLE DETECTORVEHICLE DETECTOR
STOP/BUZZER
FREE EXIT
INSIDE OBSTR
OUTSIDE OBSTR
SHADOW RESET
WIEGAND
HySecurity
COM
NO
MX000585
VERSION
S/N
RS232
DISPLAY
VEHICLE DETECTOR
COM COMA B
RPM
COMOPEN EDGE+24V +24V
STAT US
LED
24V AC Acce
s
sory power
+
24V DC
Power Connector
Power Module
COMMON
Smart Touch Controller
R3 19 FLASHER
RELAY 3 LOGIC
Mounting holes
2⅜”
Drawings NOT to Scale
N.O. (Normally Open)
Barrier Arm
If using the “Add On” kit MX001197,
connect wires together in parallel. Refer to
the instructions (D0279) supplied with the
Add On Light Kit.
Fasteners:
Bolt: ¼” x 20 x 1¾”
2 washers
1 lock nut
Flasher base
STC Display and Keypad
Access the Installer Menu:
Set R3 to 19 FLASHER
RELAY 3 LOGIC
Feed cable through chassis and into the control
box. Connect the non-polarized wire ends to the
Power Module +24V and the STC, N.O. contact on
the solid state, user relay 3.
NOTE: 7 Segment Display
Access the Installer Menu:
Set R3 to 19
StrongArm Flashing Light Kit: Interior View StrongArm Flashing Light Kit: Side View
Flat head screws
Cut away view
Red Lens
Amber Lens
www.SecureOpeners.com | [phone] | [email protected]