Hytera HR106X User manual

06073207 190335437
5202010062391A
DIGITAL REPEATER
2020
Hytera Communications Corporation Limited.
Hytera Communications Corporation Limited.
Address: Hytera Tower,Hi-Tech Industrial Park North,9108#Beihuan Road,
Nanshan District,Shenzhen,People’s Republic of China
QUICK REFERENCE GUIDE
HR106X

1
Product Overview
Front Panel
No. Part Name No. Part Name
1 Air Inlet for PA 8 Timeslot A RX Indicator
2 Volume/Channel + Key 9 Timeslot A TX Indicator
3 Volume/Channel – Key 10 Analog Mode Indicator
4Seven-segment Display 11 Digital Mode Indicator
5Alarm Indicator 12 Audio/Programming Interface
6 Timeslot B RX Indicator 13 Air Inlet for Power Supply
7 Timeslot B TX Indicator / /
Rear Panel
Basic Version
Blade Repeater
TX RX TX RX
D A SLOTA SLOTB ALARM
CH
Advanced Version
No. Part Name No. Part Name
1TX Antenna Connector 7USB Connector
2Monitor/Tuning Interface 8 DC Power Inlet
3Accessory Connector 9 AC Power Inlet
4RX Antenna Connector 10 AC Power Switch
5Ethernet Interface 1 11 Ground Screw
6Ethernet Interface 2 / /
NOTE
In routing mode, the Ethernet interface 1 and Ethernet interface 2 must serve as
LAN port and WAN port respectively.
No. Part Name No. Part Name
1TX Antenna Connector 6 DC Power Inlet
2Monitor/Tuning Interface 7 AC Power Inlet
3Accessory Connector 8 AC Power Switch
4RX Antenna Connector 9Ground Screw
5Ethernet Interface / /

2
Internal Parts
Basic Version
No. Part Name No. Part Name
1PA Module 5Wind Scooper
2Main Board 6Fan
3Network Board 7Control Panel
4 Power Supply Module 8 Float Charging Board
Advanced Version
No. Part Name No. Part Name
1PA Module 5Wind Scooper
2Main Board 6Fan
3Coprocessor 7Control Panel
4Power Supply Module 8Float Charging Board
Installation
To ensure optimum performance and reliability of the
repeater, read the following instructions carefully.
Installation Requirements
Environmental Conditions
The repeater must be installed in a dry and well-ventilated
place. The operating temperature ranges from –30°C to
+60°C, and the relative humidity is 95%.
Installation Site
The repeater can be installed in a rack, bracket, and cabinet,
or on a desk.
NOTE
For more information, refer to the Safety
Information Booklet.
Pre-installation Tasks
Preparing the Tools
●Phillips screwdriver
●T-10 torx screwdriver
●Spanner
●Anti-static gloves
●Multimeter
Checking the Power Supply
Before you install the repeater, make sure that the power
supply meets the following requirements:
●DC power voltage: 13.6±15% V
●AC power voltage: 100–240 V
Installation Procedure
To install the repeater, do as follows:
1. Wear the anti-static gloves.
2. Place the repeater to a proper location.
NOTE
If the repeater is installed in outdoor environments
with frequent thunderstorms, such as the top
of mountains or buildings, you must install an
external lightning protection module (optional) on
the network interface.
3. Connect the antenna, feed line, power cord and ground
cable to the repeater.
NOTE
●You must purchase the antenna and feed lines
separately.
●You must prepare a ground cable.
4. Ground the repeater through the ground screw located
on the rear panel.
Post-installation Check
To check whether the repeater works properly, do as follows:
1. Turn the repeater on.
2. Observe the LED indicators and the display in the front
panel.
●If the repeater works properly, the power supply
indicator on the oat charging board glows yellow
or blue, and the display shows the current channel.
●If not, the power supply indicator glows red, and
the display shows the alarm code.
NOTE
For details, see Checking the Status.

3
Basic Operations
Turning On or Off the Repeater
●If the repeater is connected to a DC power supply, press
the power switch on the DC power supply to turn on or
off the repeater.
After turn-on, if the power supply indicator turns red,
the repeater goes into locked status. You must switch off
the DC power supply for four seconds, and then switch
on the power supply again.
●If the repeater is connected to an AC power supply, press
the AC Power Switch in the rear panel to turn on or off
the repeater.
After turn-on, the power supply indicator turns yellow.
Changing the Channel
Press the Volume/Channel + or Volume/Channel – key to
change the channel.
The current channel number appears on the display of the
repeater.
Adjusting the Volume
1. Long press the Volume/Channel + key for ve seconds
to switch the repeater from channel mode to volume
mode.
2. Press the Volume/Channel + or Volume/Channel – key
to increase or decrease the volume.
If you do not have any operation for greater than five
seconds or if you long press the Volume/Channel + key
again within ve seconds, the repeater switches to channel
mode.
Checking the Status
Repeater
Indicator Description Repeater Status
Digital
Mode Blue The repeater is operating in
digital mode.
Analog
Mode Yellow The repeater is operating in
analog mode.
Alarm Red
The repeater is not working
properly, and the display
shows the alarm code.
Timeslot A
TX Red
●Analog mode: The
repeater is transmitting.
●Digital mode: The
repeater is transmitting
on timeslot A.
Timeslot A
RX Green
●Analog mode: The
repeater is receiving.
●Digital mode: The
repeater is receiving on
timeslot A.
Timeslot B
TX Red Digital mode: The repeater is
transmitting on timeslot B.
Timeslot B
RX Green Digital mode: The repeater is
receiving on timeslot B.
Network Interface
Indicator Description Repeater Status
Ethernet
Interface
LED 1
Flashing
The network interface
card is transmitting
data.
LED 2
Glowing
The data transmission
rate is 1000 Mbps/100
Mbps.
Off The data transmission
rate is 10 Mbps.
Power Supply
Indicator Description Repeater Status
Power Supply
(Visible through
the Air Inlet for
Power Supply)
Yel low The repeater is supplied
by an AC power.
Blue The repeater is supplied
by a DC power.
Red The repeater cannot be
turned on.
For details on more features and operations, please visit our
website at: http://www.hytera.com, or scan the QR code to
download the User Manual.

Operational Instructions and Training Guidelines
To ensure optimal performance and compliance with the occupational/controlled environment RF energy exposure limits in the above standards and guidelines,
users should transmit not more than 50% of the time and always adhere to the following procedures:
Antenna gain must not exceed 10dBi.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined
by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a different circuit to that of the receiver's outlet.
Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Note: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority tooperate the
equipment.
The antenna must be installed complying with the requirements of manufacturer or supplier, and it must be at least 200 cm away from human body.

ISEDC Statement
This device complies with Innovation, Science and Economic Development Canada Compliance license-exempt RSS standard(s). Operation is subject to
the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement
ISEDC Radiation Exposure Statement:
This equipment complies with ISEDC RF radiation exposure limits set forth for an occupational/controlled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance
200cm between the radiator& your body.
IC exposition aux radiations:
Cet équipement est conforme avec ISEDC les limites d'exposition aux rayonnements définies pour un environnement professionnel/contrôlé.Cet
émetteur ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne ou émetteur.Cet équipement doit être installé et utiliséavec
une distance minimale de 200cm entre leradiateur & votre corps.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an occupational/controlled environment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with
minimum distance 200cm between the radiator &you body.

RF Exposure Compliance and Control Guidelines and Operating Instructions
To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following
procedures.
Guidelines:
Do not remove the RF Exposure Label from the device.
User awareness instructions should accompany device when transferred to other users.
Do not use this device if the operational requirementsdescribed herein are not met.
Operating Instructions:
Transmit no more than the rated duty factor of 50% of the time.
Keep the radio unit at least 200 cm away from the human.