Hyundai HYTR2650 User manual

CONTENTS
Section Description
Page No/No’s
1. SAFETY
3 - 6
2. MACHINE PARTS
7
3. ASSEMBLY PROCEDURE
8 - 9
4. OPERATING PROCEDURES
10- 11
5. MAINTENANCE
12 -14
6. TROUBLESHOOTING
15
7. STORAGE
16
8. SPECIFICATION
16
9. GENPOWER CONTACT DETAILS
17
10. DECLARATIONS of CONFORMITY
18
Page 2

1. SAFETY.
1.1. The operator of the machine;
1.1.1. Is responsible for and has a duty of care in making sure that the machine is operated safely
and in accordance with the instructions in this user manual.
1.1.2. Should never leave it in a condition which would allow an untrained or unauthorised
person/s to operate this machine.
1.1.3. Should take care and show due diligence for the safety of and with regard to those around
whilst using the machine, to include but not limited to;
1.1.3.1. Elderly, children, pets, livestock and property.
1.2. Some or all of the following PPE, Warning Signs and symbols may appear throughout this manual
and you must adhere to their warning/s. Failure to do so may result in personal injury.
Personal Protective clothing (PPE)
Warning Signs and Symbols
Page 3

1.3. Carbon Monoxide
1.3.1. Carbon monoxide is a colourless and odourless, inhaling this gas can cause death as well as
serious long term health problems such as brain damage.
1.3.2. The symptoms of Carbon monoxide poisoning can include the following;
1.3.2.1. Headaches, Dizziness, Nausea, Breathlessness, Collapsing or Loss of consciousness.
1.3.2.2. Carbon monoxide symptoms are similar to flu, food poisoning, viral infections and
simply tiredness. That’s why it’s quite common for people to mistake this very dangerous
poisoning for something else.
1.3.3. To avoid Carbon monoxide poisoning DO NOT Use Petrol/Diesel powered equipment inside
a home or garage even if doors and windows are open.
1.3.4. If you think you or someone around you has been affected by carbon monoxide poisoning;
1.3.4.1. Get fresh air immediately.
1.3.4.2. Open doors and windows, turn off machine and leave the affected area.
1.3.4.3. See your doctor immediately or go to hospital - let them know that you suspect
carbon monoxide poisoning.
1.3.5. DO NOT use in an enclosed area or a moving vehicle.
1.4. General fuel safety.
1.4.1. Fuel Safety additional information can be obtained from the Health and Safety Executive
(HSE) document SR16.
1.4.2. All fuels are Flammable.
1.4.3. Keep away from all ignition sources i.e. Heaters, Lamps, sparks from Grinding or welding.
1.4.4. Hot work on tanks that have contained fuel is extremely dangerous and should not be
carried out.
1.4.5. Keep work area clean and tidy.
1.4.6. Clean up all spills promptly using correct methods i.e. absorbent granules and a lidded bin.
Page 4

1.4.7. Dispose of waste fuels correctly.
1.5. Petrol safety.
1.5.1.1. Always fuel and defuel in well-ventilated area.
1.5.1.2. Always wear correct, suitable and fit for purpose Personal Protective Equipment
(PPE), suggested items are as follows, but are not limited too.
1.5.1.3. Hand protection.
1.5.1.4. Protective clothing.
1.5.1.5. Respiratory protective equipment should be used when in an unventilated
area.
1.5.1.6. When defueling always use a propriety fuel retriever.
1.5.1.7. Always carry fuel in the correct and clearly marked container.
1.6. Tool safety
DO NOT modify the unit in any way.
Only use the tool for the job for which it is intended.
Always remove HT lead from spark plug when checking machine or changing parts.
1.6.1. Inspect machine before each use, and replace any damaged parts before operation. Check
for fuel leaks and make sure all fasteners are secure and in place. Make sure the safety guard
is properly attached.
1.6.2. Replace parts that are cracked, chipped or damaged in any way before using the tool. Make
sure the safety guard is properly attached.
1.6.3. Use only recommended accessories and parts, approved by the manufacturer. Non
approved attachments may cause damage to the machine or harm to the user, and will also
void your machine’s warranty.
1.6.4. When replacing the spool line, always use certified replacement sourced from the
manufacturer. Only use genuine Hyundai spare parts.
Page 5

1.6.5. Under no circumstances should you ever take the product apart or alter it in any way even if
the item is faulty. You may damage or cause further harm by taking the product apart and you
will void your warranty in doing so.
1.6.6. This grass trimmer is designed exclusively for cutting garden areas in a private domestic
setting. Using it for any other purpose other than those intended qualify as improper use. The
operator is solely responsible for assuming all risks.
1.6.7. Do not overload the machine. It will safer and better when operated within its specified
performance range.
1.6.8. Keep others away from machine when making carburetor adjustments’ or changing spool
line
Page 6

2. MACHINE PARTS
1
Spark Plug
9
Safety Trigger
2
Air Filter
10
Throttle Lock
3
Choke Lever
11
Handle
4
Starter Pull Cord
12
Clamp
5
Primer Bulb
13
Spool head
6
Fuel Tank
14
Trimmer guard
7
Throttle Trigger
15
Fuel Mixing Container
8
Ignition Switch
16
Belt/Harness
Accessories: 1 x Trimmer guard; 1 x Belt/Harness; 1 x Fuel Mixing Container; 1 x Allen
key 4mm: 1 x Allen key 5mm & 1 x Open ended wrench.
Page 7

3. ASSEMBLY PROCEDURE
Anti-vibration systems do not guarantee that you will not sustain white finger
disease or carpal tunnel syndrome. Therefore, continual and regular users should
monitor closely the condition of their hands and fingers. If any of the above
symptoms appear, seek medical advice immediately.
Remove HT lead from spark plug when assembling the machine or changing parts.
3.1. Handle assembly.
3.1.1. Assemble the handles onto the upper shaft.
3.1.2. Insert the screw, washer and handle knob.
3.1.3. Tighten the handle knob.
3.2. Drive shaft assembly.
3.2.1. Press the lock hook and insert the drive shaft, make sure
the lock hook goes into the hole on the drive shaft,
3.2.2. When the shaft is assembled into place, tighten the
clamp knob.
Page 8

3.3. Trimmer guard assembly.
3.3.1. Insert the trimmer guard.
3.3.2. Tighten screw with 5mm Allen key.
3.4. Replacing the spool line.
3.4.1. Remove bump head knob by turning anti-
clockwise.
3.4.2. Remove the spool and spring from spindle.
3.4.3. Measure approximately 26 feet (8 metres)
of line, then thread one end through the
hole on the spool. Pull the line until the two
line lengths are equal.
3.4.4. Wind both line tightly and evenly from
side to side and feed the line while turning
the spool in the direction of the arrow. Do not
allow the lines to get twisted.
3.4.5. When you have about six inches (150mm) of
line remaining, press the line into the two
notches on the bottom of the spool. This will
hold the line on the spool ready for re-assembly.
3.4.6. Install the spring over the spindle.
3.4.7. Insert each end of the cutting line through the
eyelets in the cutting head assembly and lower
the spool while feeding the line.
3.4.8. Once the spool is in place, apply pressure on
the spool compressing the spring. Pull each end
of the line sharply to unlock the line from the
slots.
3.4.9. Continue to apply pressure to the spool until
the knob can be threaded clockwise onto the
spindle.
3.4.10. Tighten the knob securely.
Make sure the line is only sticking out of the metal eyelets on the head.
Page 9

4. OPERATINGPROCEDURES
The trimmer is equipped with a two stroke engine. Always run the engine on
unleaded fuel mixed with two stroke oil N.B. see specification section.
Always carry out fueling processes outside.
Always wear correct Personal
Protective Equipment (PPE) when
using machine Minimum
Recommended PPE.
4.1. Fuel.
4.1.1. Always use fresh unleaded petrol.
4.1.2. Pre-mix 2-stroke oil with fresh unleaded petrol as follows:
4.1.2.1. Synthetic 2-stroke oil: 40:1 (25ml of oil per 1 litre of petrol)
4.1.3. Never use multi-grade or waste oils.
4.1.4. Always mix fuel and oil in a separate clean container.
4.1.5. Start by mixing half of the required fuel with the whole amount of oil, mix (shake) the fuel
oil mixture.
4.1.6. Add the remainder of the fuel.
4.1.7. Re-mix the fuel oil mixture.
4.2. Fueling.
4.2.1. Always shut off the engine before fueling.
4.2.2. Before fueling make sure the tank cap area is clean. This will prevent dirt and debris
entering the tank.
4.2.3. Slowly open the fuel tank this will allow any pressure build up to disappear.
4.2.4. Fill tank with premixed fuel.
4.2.5. Always make sure that the fuel cap is secured tightly.
4.2.6. Always move the engine/equipment at least 3 metres (10 feet) away from the fueling area
before starting machine.
4.3. Starting.
Before starting, make sure the cutting attachment does not touch anything
4.3.1. Set the ignition switch (8) to the ON position. Push priming bulb (5) several times so that the
fuel flows through the return pipe.
4.3.2. Press safety trigger (9), pull throttle trigger (7) and push throttle lock (10), then slowly
release the throttle trigger first, then the safety trigger. This will lock the throttle in the
starting position.
4.3.3. Set choke lever (3) to the OFF position.
Page 10