i-MO i3A12X/10A01-SOO User manual

i³…Display, Control, Connect…
User Guide

i³
i3
User Guide
Introduction to i32
Guide to Part Numbers 2
Installing i3Configurator Software 3
Powering up and Connecting to an i36
Tour of the i3Configurator 7
Linking and Configuring the Controller 8
Automatic 9
Manual 10
Creating a Program 11
Example 12
Program Options 17
Example 18
Running and Monitoring the i3 Program 18
i3Help File 20
Appendix A: Data Types 21
Appendix B: i3 Register Types 22
Appendix C: System Bits 23
Appendix D: System Registers 23
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
1

i³
Introduction to i3
The i3is a brand new concept in control product. It is a combination of a mini-PLC
and HMI (pixel based 128x64 backlit LCD display). It is a cost effective family of
high performance all-in-one controllers.
The i3features an advanced control engine, operator interface, local and remote I/O
capabilities, and a variety of communications options. The i3is extremely versatile
and adept at a variety of automation functions.
The i3can be used to perform advanced machine control, factory machine monitoring,
and process control.
Guide to Part Numbers
Model Number Digital
Inputs
Analogue
Inputs
Digital
Outputs
Analogue
Outputs
HSC PWM CAN
i3A12X/10A01-SOO 12 1 x 10 bit 6 Relay 4 No
i3A12X/10D03-SCH 12 4 x 10 bit 6 Relay 4 Yes
i3A12X/10B04-SCH 12 2 x 10 bit 12x.5A 4 2 Yes
i3A12X/20B05-SOH 24 2 x 10 bit 16x.5A 4 2 No
i3A12X/13C14-SOH 12 2 x 14 bit 12x.5A 2 (V or mA) 4 2 No
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
2

i³
Installing i3Configurator Software
The IMO i3Configurator software can be obtained from a CD or download from the i3
Configurator software from the IMO website: www.imopc.com
Double click on the icon with the right mouse
button to open the installation program.
Follow the steps in the installation wizard to install the i3Configurator to your PC.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
3

i³
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
4

i³
Tick the “Launch the program” box and click Finish.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
5

i³
Powering up and Connecting to an i3
Connecting power to the i3
+24VDC in
the middle,
0V to the left
When power is applied the i3will then
run a system diagnostic before running
the user program.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
6

i³
To connect the i3 to a PC, connect the i3-PC45, RJ45 end into port 1 of the i3 and the 9
pin serial connector into the serial port of the PC (or USB to Serial adaptor).
Port 1: Programming
port
Tour of the i3Configurator
To launch the i3Configurator program, either select the option from the Programs
menu in Windows or double click the icon on the desktop with the right mouse
button.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
7

i³
The program is launched and we are faced with a blank new program named
“untiled1.csp”.
Linking and Configuring the Controller
Controller
IEC
Programming
Program Rungs &
Rung options
Programming
Area
Help File!
Programming
elements
Edit screens
menu
Verify, Download &
Upload the program
Configure
the
Controller,
Set comm.
Parameters,
RUN the
controller
Open
existing
programs,
Save
programs,
Create New
programs
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
8

i³
With an i3connected it will automatically link to the i3configurator software and set
up the Controller, however it is best to check.
Click the icon or select
from the Controller menu
“I/O Configure”
There are two ways to configure the controller, manually or automatic.
With an i3connected to the PC the easiest method is to Auto-Config.
Automatic
Click on the Auto-Config button. A warning pop up will appear, click Yes.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
9

i³
Correct type
and model
have now
been set up
Manual
To configure the
Controller manually click
on the Config button with
the right mouse button and
then select the type of
controller from the pull
down list. Then select the
correct model number.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
10

i³
Creating a Program
Creating a New program, Saving a program or Opening an existing program, all
done in the file menu.
C
li
c
k
o
n
t
h
e
i
co
n
o
r
se
l
ect
fr
o
m
t
h
e
m
e
n
u
C
li
c
k
o
n
t
h
e
i
co
n
o
r
se
l
ect
fr
o
m
t
h
e
m
e
n
u
C
li
c
k
o
n th
e
i
co
n
o
r
se
l
ec
t fr
o
m th
e
m
e
n
u
Recently opened programs
The program file name format is “program_name” followed by the extension .csp
For example, program_name.csp
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
11

i³
Example
Create a new program and save it. Name the program “bestofbothworlds”.csp
Select the Boolean elements and right click the mouse on the NC contact.
Insert it at A1.
Insert the following detail into the contact
Now using the Boolean elements insert contacts and coils to make the following
latching ladder diagram.
Variable Name Address Type
EM_STOP %I0001 NC CONTACT
START %K0001 NO Function Key
STOP %K0002 NO Function Key
RUN %Q0001 NO Coil & Contact
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
12

i³
Now select another NO coil and insert it to the right of the RUN coil. When the I/O
point menu pops up, click the screen button.
Click here
N
ow click
Edit screen
Select the
top left
screen.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
13

i³
This will open up the screen editor.
Select the Text Table button and right click on the screen.
Double click on the word box to open up the properties.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
14

i³
Enter the
details as
shown
Click on the
Text table
button.
Once the
Text table
has been
set up click
the Legend
b
utton
Click Add and
assign the string
STOPPED to the
value 0, Click OK.
Click Add again and
assign the string
RUNNING to the
value 1. Finally click
OK to exit the Text
Table Entry.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
15

i³
Delete the
default text and
enter the
details shown.
Click OK.
The Text
Table box
may need to
be resized.
Click and
hold on the
edge of the
box and drag
bigger
Now close the graphic edit by clicking on the cross at the top right of the window.
Click OK and the I/O point pop up window
The ladder diagram will now look like the diagram below.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
16

i³
Program Options
Downloading, Uploading and Error Checking the program.
To Download or Upload
from the i3 either select the
options from the menu or
click on the icon.
It is a good idea to Error
Check the program before
downloading. Click the icon
or select from the menu.
The error check gives
the user a report on the
p
roject and lists any
errors found.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
17

i³
Example
First Error Check the program you just created and then download it to the controller.
Tick the Use
SmartLoad and click
OK.
Running and Monitoring the i3 Program
The i3 will be by default in STOP mode and requires to be put into RUN mode for the
programmed i3 to operate.
Start Pause Stop
Either use the icons or
select from the menu.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
18

i³
To Monitor the
RUNNING program
either select from the
menu or click the icon.
When the program is being monitor, made contacts and coils are shown in red.
No part of this publication may be reproduced without the prior agreement and written permission of IMO Precision Controls Ltd.
Information in this document is subject to change without notice.
19