i-PRO Zafiro User manual

1
Zafiro
Quick Start Guide
2
LEGAL INFORMATION
All rights reserved.
No part of this publication may be quoted, reproduced,
translated or used in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without the
prior written permission of IPRO mobile which is hereinafter
named IPRO in this user guide
Notice
IPRO reserves the right to make modifications on print errors
or update specifications in this guide without prior notice.
Disclaimer
IPRO expressly disclaims any liability for faults and damages
caused by unauthorized modifications of the software.
Images and screenshots used in this guide may differ from the
actual product. Content in this guide may differ from the actual
product or software.
Trademarks
The Bluetooth®trademark and logos are owned by the
Bluetooth SIG, Inc. and any use of such trademarks by IPRO
is under license.
microSDXC Logo is a trademark of SD-3C, LLC.

3
Getting to Know Your Phone
4
Installing the SIM Cards/microSDXC™
Card and Battery
Power off your phone before installing or removing the SIM
cards/microSDXC card. And power off your phone before
removing or replacing the battery.
WARNING!
To avoid damage to the phone, do not use any other kind of
SIM cards, or any non-standard SIM card cut from a SIM card.
You can get a standard SIM card from your service provider.
1. Insert your fingernail into the slot at the bottom left of
the back cover and lift it up gently.
2. Hold the SIM card with the cut corner oriented as
shown and slip them into the card slots.

5
3. Hold the SIM card with the cut corner oriented as
shown and slip them into the card slots.
4. Insert the battery by aligning the metal contacts on the
battery with the metal contacts in the battery
compartment. Gently push down on the battery until it
clicks into place.
5. Align the back cover with the back of the phone and
press the cover back into place. Ensure that all the tabs
are secure and there are no gaps around the cover.
6
Charging the Phone
Your phone’s battery should have enough power for the phone
to turn on, find a signal, and make a few calls. You should fully
charge the battery as soon as possible.
WARNING!
Use only IPRO-approved chargers and USB cables. The use
of unapproved accessories could damage your phone or cause
the battery to explode.
1．Connect the adaptor to the charging jack.Ensure that
the adaptor is inserted in the correct direction.
2．Connect the charger to a standard AC power outlet.
3．Disconnect the charger when the battery is
fully charged.
NOTE:
If the battery is extremely low, you may be unable to power on
the phone even when it is being charged. In this case, try
again after charging the phone for at least 20 minutes. Contact
the customer service if you still cannot power on the phone
after prolonged charging.
NOTE:
If the screen freezes or takes too long to respond, try pressing
and holding the Power key for about 10 seconds to restart the
phone.

7
Product Safety Information
Don’t make or receive phone calls while driving.
Never text while driving.
Keep your phone at least 5 mm away from your
body while making calls.
Small parts may cause choking.
Your phone can produce a loud sound.
To prevent possible hearing damage, do not listen
at high volume levels for long periods. Exercise
caution when holding your phone near your ear
while the loudspeaker is in use.
Avoid contact with anything magnetic.
Keep away from pacemakers and other electronic
medical devices.
Turn off when asked to in hospitals and medical
facilities.
Turn off when told to on aircraft and at airport.
Turn off when near explosive materials or liquids.
Don’t use at gas stations.
Your phone may produce a bright or flashing light.
Don’t dispose of your phone in fire.
Avoid extreme temperatures.
Avoid contact with liquids. Keep your phone dry.
Do not attempt to disassemble your phone.
Don’t rely on your phone as a primary device for
emergency communications.
8
FCC Warning
Specific Absorption Rate (SAR) information SAR tests are
conducted using standard operating positions accepted by the
FCC with the phone transmitting at its highest certified power
level in all tested frequency bands, although the SAR is
determined at the highest certified power level, the actual SAR
level of the phone while operating can be well below the
maximum value, in general, the closer you are to a wireless
base station antenna, the lower the power output.
Before a new model phone is a available for sale to the public,
it must be tested and certified to the FCC that it does not
exceed the exposure limit established by the FCC, Tests for
each phone are performed in positions and locations (e.g. at
the ear and worn on the body)as required by the FCC.
For body worn operation, this mobile phone has been tested
and meets the FCC RF exposure guidelines when used with
an accessory designated for this product or when used with an
accessory that contains no metal and that positions the
handset a minimum of 1.0cm from the body.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by

9
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for
help.