I-View CZ-537-IP User manual

Rev. 3-2-2012
CZ-537-IP IR Night Vision
Network PTZ Cameras

Contents
1 Instruction..................................................................................................... 1
1.1 Safety Instructions............................................................................ 1
1.2 Warnings........................................................................................... 1
2 Feature.......................................................................................................... 2
2.1 Product Features............................................................................... 2
2.2 Specifications ................................................................................... 3
3 Installation Instruction.................................................................................. 4
4 Software Installation Instructions................................................................. 6
4.1 Client User Instruction...................................................................... 6
4.2 Main Interface .................................................................................. 6
4.3 Toolbar.............................................................................................. 9
4.3.1 Image Quality......................................................................11
4.3.2 OSD.................................................................................... 12
4.3.3 Shelter ................................................................................ 12
4.3.4 Motion Detection................................................................ 12
4.4 Setting............................................................................................. 13
4.4.1 Client Setup........................................................................ 13
4.4.2 Video Switch Setting.......................................................... 13
4.4.3 Local User Management..................................................... 13
4.4.4 Automatic-Record.............................................................. 13
4.4.5 Playback............................................................................. 14
4.4.6 Language Version............................................................... 14
4.4.7 Full Screen ......................................................................... 14
4.5 Device property.............................................................................. 14
4.5.1 Address/Port....................................................................... 15
4.5.2 DDNS................................................................................. 15
4.5.3 PPPoE................................................................................. 15
4.5.4 Multicast............................................................................. 16

4.5.5 E-Mail ................................................................................ 16
4.5.6 Date/Time........................................................................... 16
4.5.7 Alarm In............................................................................. 16
4.5.8 Alarm Out........................................................................... 17
4.5.9 PTZ..................................................................................... 17
4.5.10 Video Channel.................................................................. 17
4.5.11 Audio Channel.................................................................. 17
4.5.12 User Management............................................................. 17
4.5.13 Update.............................................................................. 18
4.6 LAN and WAN configuration......................................................... 18
4.7 Application for DDNS.................................................................... 19
4.8 Router configuration....................................................................... 19
4.9 IE mode.......................................................................................... 19
5 How to Use OSD Menu.............................................................................. 20
5.1 Basic operation of Main menu........................................................ 20
5.2 Main Menu..................................................................................... 21
5.2.1 System Information............................................................ 22
5.2.2 Address Setting................................................................... 22
5.2.3 Motion................................................................................ 23
5.2.4 Patterns............................................................................... 24
5.2.5 Camera Setup ..................................................................... 25
5.2.6 Cruise Setting..................................................................... 35
5.2.7 IR Setting ........................................................................... 35
5.2.8 Display Setup ..................................................................... 36
5.2.9 Restore Factory Default...................................................... 36
5.2.10 Reboot System.................................................................. 36
6 Trouble Shooting ........................................................................................ 37
7 Fast Control Chart ...................................................................................... 38
Appendix I DIP Switch Setup........................................................................ 39

1
1 Instruction
These series of products can be widely used in intelligent building, bank
security, urban roads, airport terminals and bus stations, and also are able to
satisfy various demands from any square and activities occasion.
1.1 Safety Instructions
Make sure to read the use’s manual before using the product.
Always confirm to national and local safety codes during installation.
Only qualified and experienced person can carry on this installation and
maintenance.
Use reliable tools, otherwise may lead to dangerous incidents.
Make sure that the environmental conditions meet the installation
requirements for this product.
Please check the space and toughness of the site before installing. It
should be able to bear 4 times the weight of the dome and its
accessories.
Please keep all the original dome package materials for future repacking
and transporting.
1.2 Warnings
Do not install this speed dome in hazardous places where combustible or
explosive materials are stored or used.
Do not place the machine on shaking desk.
Make sure no uncertain object or fluid substances get inside the unit.
Do not turn power on before finishing installation.
Do not disassemble any part of the items.
Use soft towel to clean the down cover when necessary, do not use
caustic detergent.
To protect CCD, avoid facing the camera directly to the strong light.
To prevent damage, do not drop the unit or subject to strong shock or

2
vibration.
2 Feature
2.1 Product Features
* OSD menu;
* 254 presets;
* Auto flip;
* Proportional zoom;
* Day & night function;
* RS485 communication;
* Protocol and baud rate auto detected;
* Soft address enables to set up the address and number of the camera;
* Multiple scans: frame scan (speed adjustable); 4 patterns; 3 tours; 360°
random scan; 360° continuous scan; parking action; power up action; etc.
IP Function
* H.264 video compression format;
* Support CIF/D1 format;
* Support mobile, RS485, alarm, intercom and monitor interface;
* Support SMTP, could send the picture in the accident place when alarm;
* Built-in Web Server, support IE browser surveillance, configuration and
update;
* Motion detection, can trigger automatic recording, fixed time recording and
manual recording;
* OSD menu is provided to display the status of camera and to configure the
functions interactively.
* User accession permission should be setting.

3
2.2 Specifications
Model IR IP Mini Variable Speed Dome Camera
Help Selection Ceiling
Power Supply DC12V/2A 50Hz/60Hz
Power ≤15W
Pan Speed 0.5°~50°/ sec
Tilt Speed 0.5°~30°/ sec
Pan Range 360°continuous
Tilt Range 0°~90° auto flip
Preset 254
Pan Scan
frame scan; 360° random scan; 360°
continuous scan;
Pattern 4
Cruise 3
OSD Menu Chinese/English
IR Illumination ON/OFF (option)
IR Distance ≥20m
Baud Rate 2400bps,4800bps,9600bps auto adaptive
Video Compression Format H.264
Video Format CIF/D1
Transmission Protocol
TCP, UDP, IP, HTTP, FTP, SMTP, DHCP,
DNS
Access Mode IE, Mobile, Client
Protocol PELCO-D, PELCO-P
Communication RS485
Address 255
Work Temperature -10°C~40°C

4
Camera Module
Support 10X Samsung, Sony camera
module,
compatible 38*38 CCD with
fixed focus lens.
3 Installation Instruction
3.1 Installation
A. Fixed the ceiling installation board with supplied screws. The board
dimension as shows:
B. Install the dome camera as shows:

5
3.2 System Connection
3.3 Dip Switch Setup
Dip Switch as follows:
Notice: Dip Switch Address Setup see appendix I

6
4 Software Installation Instructions
4.1 Client User Instruction
System requirement
Operating System: Windows 2000/XP/Vista
Processor: Intel Pentium III, 1G or Higher (Pentium IV, 2G or
Higher recommended)
RAM: 256 MB or more
Color Monitor: At least DirectX 8.1 or higher and 32M Display
storage
HD: More than 40G
Double-click the Program of Client Software Package to install the software:
4.2 Main Interface
Double click to run the program, and then enter the user
information, default is blank. Change the user information see
<Setup>→<Administration>.
Main Interface:

7
First user should add the IP/ Host name in the client software to open the
surveillance picture. Steps are following:
1). Click the right side <Devices>button , will pop up:
Note: If the device is not in the same network segment, Client could auto
search but cannot connected. Modify the IP device’s IP and gateway, or

8
add one more IP in the same network segment.
2). For the device cannot search with network, user could add IP/Host
manually. Click <Add>, the following will pop out:
Note: Access to the Video/transfer server program, the Host chooses
“Proxy”.
3). Input the IP/Host, for example, the IP/Host is testdvs3322.org, and port is
8001, the Host chooses DVS/IP CAM, click<OK>.
4). Double click the device list, and then pop out the connected window, input
the administrative and password, the default is “Admin”.
5). Click <Connect>, and then the main interface on the right will show the
device address, chooses channel 1, press left key and drag it to the left window.
The monitor picture show out.

9
4.3 Toolbar
From Left to right: Information; Talkback; Sound; Snapshot; Record; Color;
Setup; Flip/Rotate; and Open.
Zoom
Focus
Iris
Preset Point
Cruise Tracks

10
Navigation
Zoom In/Out
Focus+/-
Iris+/-
Preset Point
Edit Cruise-track
Stop Cruise
Devices
Property
Disconnect
Save/Delete
Scene
Cruise Tracks
Display
channels,
support
1/4/6/8/9/12/
16/20/25/30
window
display

11
4.3.1 Image Quality
Image Quality could set Stream Style, Coding Style, Frame, Gaps between
I-Frames.
<Coding Style>: ①Quality first;②Rate first
<Up limit>: When the coding stale is Rate first, the actual coding would
not exceed the value. The default value is 1024kps.
<Frame rate>: It means the frames per second in the video. The value
range from 1~25, the default value is 22 Fps.
<I Frame Interval>: In the process of video transmission, one I frame in
per 100 frames. The default value is 100.

12
4.3.2 OSD
OSD Menu could set channel information, time, the color and the position of
text.
4.3.3 Shelter
Shelter means cover one part of picture in the monitor screen. Hold <Ctrl> to
select shelter area, click <Clear> key to clear the shelter.
4.3.4 Motion Detection
<Motion detection setup>: Hold <Ctrl> to select the detection area, at
most 4 areas could be set.
<Sensitivity>: The value is larger the sensitivity is better.
<Valid period of time>: Setup motion detection of the alarm durable
time and the triggering alarm time.
<Alarm handling ways>: Sound, inform user and send Email.

13
<Output to Channel>: You could choose the other channels except the
nominated channel to display the motion detection result.
4.4 Setting
4.4.1 Client Setup
Click , save the video path, alarm trigger recording time, alarm
playback sound, and the scene you exist last time. It could be set several video
paths, the default is saving in the first path, when the first path is full, and it
will save in the next path.
4.4.2 Video Switch Setting
Video Switch setting could change the picture automatically on the same
screen to different devices or channel. Click <Pages>, turn up and down to
increase or decrease the pages. Click<Stay>turn up and down to increase or
decrease the time for staying. Click the layout window to set the display mode,
press and hold the left mouse button to drag the right side of the channel to be
displayed, double-click the right side of the channel to remove it.
4.4.3 Local User Management
User should use password when login, the initial password is empty. User can
increase the corresponding user name and password and operating authority.
If the screen in lock or full-screen mode should use password when exit.
4.4.4 Automatic-Record
Automatic-Record Setting is automatically recording a piece of time for
equipment, video file path save in page setup <Client Setup>.Start
automatic-record, the client kept the upper right corner will be flashing
green light.

14
4.4.5 Playback
Click pop out the window, you could find the video file from the
saved catalogue or event. Double click the video file to play.
4.4.6 Language Version
The software support Chinese and English, click pop
to switch.
4.4.7 Full Screen
Click change to full screen mode, all action will be locked under
this mode, input administrator password when quit. Click the right button to
pop：
4.5 Device property
Click or choose IP address in device list, click <Property>by
right key to pop dialog, setup or adjust IP address、DDN、PPPoE、broadcast
configuration、user management、update online, etc.
Choose to pop alarm info

15
4.5.1 Address/Port
Default IP address:192.168.0.233, subnet mask:255.255.255.0 ，
gateway:192.168.0.1, service port 8001. After change, system will register
you restart your device to valid the setup. Change service name not need
restart.
Notice 1: IP address will valid only after device restart.
Notice 2: When link 2 or more devices, need change related IP address
and physical address.
Notice 3: Outer net visit need mapping the service port, refer router
configuration part. DNS server needs change to current DNS IP address
also.
4.5.2 DDNS
DDNS mean dynamic DNS, for unfixed IP domain name mapping. This client
software support peanut shell and 3322 DDNS Service. Just apply your
domain name in the proper network station (refer to Part 4.7) then click
<OK> in the pop dialog, the DDNS will valid.
<DDNS Service Provider>: Now support www.oray.net and
www.3322.org.
<User Name>: One account can apply different domain name, the
provider request not same.
<Password>: The password is that you apply the domain name setting.
<Dynamic Domain Name>: According to domain integrated address.
4.5.3 PPPoE
The client software allows PPPoE. Link the device to phone line through
modem, dial to internet. User can visit the monitor picture by internet from
long distance. Choose PPPoE in the dialog then input user name and password
then click <OK>.

16
4.5.4 Multicast
Use set device as needed to realize the multicast function.
4.5.5 E-Mail
When choose mail service, the device will send event report and picture to the
appointed mailbox when alarm or Motion Detection triggered.
<SMTP Server>: Follow your mailbox hints for related setup.
<SMTP Port>: Default is 25.
<Sender’s Account>: Need according to the SMTP service if your
mailbox support.
<User Account>: When enter the user account, it could auto catch
account information that has been used.
<Password>: Account related password.
<Receiver’s Account>: Any mailbox which can receive mail.
Click<Send ATest Mail> after setup to confirm your action.
Notice: For outlook or foxmail user, need set the sender account to valid
the function.
4.5.6 Date/Time
Adjust device date, time. Click <Same with PC>to synchronous with PC.
4.5.7 Alarm In
<Channel>: Allow setup name for choosing channel.
<Actions take to response to alarm>: Sound alarm, notice client and
send e-mail.
<Output to >: Setup output channel.
<PTZ linkage>: There are 3 kinds of linkage: separate, preset and cruise.
Monitor channel must be appointed when choose preset or cruise mode.
<Valid period of time>: Setup alarm input time period. "+" mean valid
period, "-" mean except the period.

17
4.5.8 Alarm Out
<Channel>: Allow setup name for choosing channel
<Valid period of time>: Setup alarm output time period. + mean valid
period, - mean except the period
4.5.9 PTZ
<Video Channel>: Choose video channel.
<Address>: Matching the PTZ address with protocol.
<Protocol>: Support Pelco-D & Pelco-P, default is Pelco-D.
<Step Length>: Range 1~64, default 32.High speed will make the
control hard; suggest under 32 for high speed dome.
<Comm Setting>: Set baud rate, data bit, stop bit, verify bit.
4.5.10 Video Channel
<Channel>: Choose the channel.
<Name>: Setup the channel name.
<Resolution>: 4 kinds: QCIF / CIF / Half_D1 / D1.
<PAL/NTSC>: Choose PAL or NTSC.
4.5.11 Audio Channel
<Channel Number>: Choose the channel No.
<Bits Width>: 8bits / 16bits / 32bits for optional.
< Sampling Rate >: The effect will better with frequency increase.
<Compression>: Choose different mode to compress audio steam (about
10 times).
Notice: Suggest keep the default setting in normal. Just click
open talkback and voice function.
4.5.12 User Management
User management is use to add, delete or modify user name and password,
and setup corresponding authority. User name can only be English character