IBASE Technology IB909F User manual

IB909F
Intel®Broadwell-ULT
3.5” Disk Size SBC
USER’S MANUAL
Version 1.0

Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® 5th Generation Mobile CoreTM i MCP Processor
are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
NUVOTON is a registered trademark of NUVOTON Technology
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii IB909 User’s Manual

Table of Contents
Introduction.......................................................1
Product Description.............................................................1
Checklist..............................................................................2
IB909F Specifications.........................................................2
Board Dimensions...............................................................4
Installations.......................................................5
Installing the Memory.........................................................6
Setting the Jumpers .............................................................7
Connectors on IB909F ......................................................11
BIOS Setup.......................................................23
BIOS Introduction.............................................................24
BIOS Setup........................................................................24
Advanced Settings.............................................................26
Chipset Settings.................................................................37
Security Settings................................................................40
Boot Settings.....................................................................41
Save & Exit Settings .........................................................42
Drivers Installation......................................43
Intel Chipset Software Installation Utility.........................44
VGA Drivers Installation ..................................................47
Realtek HD Audio Driver Installation...............................49
LAN Drivers Installation...................................................51
Intel® Management Engine Interface ...............................55
Appendix...........................................................57
A. I/O Port Address Map...................................................57
B. Interrupt Request Lines (IRQ)......................................58
C. Watchdog Timer Configuration....................................59
IB909F User’s Manual iii

This page is intentionally left blank.
iv IB909 User’s Manual

INTRODUCTION
Introduction
Product Description
The IB909F is a 3.5-inch single board computer based on the Intel®
Broadwell-ULT MCP processors.
The IB909F platform is well suited for low-power and
high-performance designs in a broad range of markets including
Industrial Control & Automation, Digital Signage, Thin Client,
Electronic Gaming Machines, and SMB storage appliances.
IB909F Features:
•Supports Intel®5th generation mobile CoreTM i MCP processors
•Two DDR3L SO-DIMM, 1333/1600 MHz, Max. 16GB
memory
•Integrated graphics for DVI-I, LVDS displays
•2 x SATA III connector
•2x COM port connector
•2 x Mini-PCIe(x1) slot (w/ USB/MSATA support)
•2x GbE (RJ-45) connector
•1x 9V to 24V DC-IN power connector
IB909 User’s Manual 1

INTRODUCTION
Checklist
Your IB909F package should include the items listed below.
•
The IB909F SBC
•
This User’s Manual
•
1 CD containing chipset drivers and flash memory utility
•
Optional cable kit (containing DC in power cable/PW87, COM
port cable / PK1H, SATA & HDD power cable/SATA-26 and
USB 2.0 cable/USB-29)
•
Other options: Audio-18 audio cable, HSIB908-BGA-1 heatsink
IB909F Specifications
Product Name
IB909F
Form Factor
3.5” SBC
CPU Type
- Intel®5th generation mobile CoreTM i MCP processors (22nm
monolithic)
- TDP = 15W (DC) , FCBGA1168 @ solder side
CPU Speed
Intel®CoreTM i7-5650U processor (2.2GHz) [IB909AF-5650]
Intel®CoreTM i5-5350U processor (1.8GHz) [IB909AF-5350]
Intel
®
Core
TM
i3-5010U processor (2.1GHz) [IB909F-5010]
Cache
Up to 4MB
Chipset
Integrated in Intel®5th Generation CoreTM i U-series processor
BIOS
AMI BIOS
Memory
Intel®5th Gen. CoreTM i U-series processor integrated memory
controller
- DDR3L (1.35V) @1600 MHz, SO-DIMM [204-pin vertical] x 2
- Max. 16GB, Non-ECC
Display
Intel®5th Gen. CoreTM i U-series processor integrated Gfx,
supports 3 independent displays, Direct X 11.1, OpenGL 4.2,
Open CL 1.2
- DVI-I x 1 (Thru DDI#1 w/ Level shifter [ASM1442K] for DVI +
DP to VGA [NXP PTN3392] )
LVDS
- LVDS(Thru eDP, via NXP PTN3460 bridge IC)
24-bit dual channels LVDS interface w/DF20 socket x2
LAN
Intel® I218LM GbE PHY (IB909AF-5650& IB909AF-5350)
or I218V GbE PHY (IB909F-5010 & IB909F-3765)
Intel
®
I211AT as 2
nd
GbE
USB
- Intel®5th Gen. CoreTM i U-series processor integrated USB 2.0
host controller, supports 4x USB 2.0: 2-ports onboard pin
header + 2 port thru MiniPCIe
- Intel®5th Gen. CoreTM i U-series processor integrated USB 3.0
host controller, supports 2x USB 3.0 in the rear panel
2 IB909 User’s Manual

INTRODUCTION
Serial ATA Ports
Intel®5th Gen. CoreTM i U-series processor built-in SATA
controller
2 x SATA 3.0 (6Gbps) and 2 x mSATA via MiniPCIe slots
(w/NXP CBTL02043A switching IC)
Audio
Intel®5th Gen. CoreTM i U-series processor built-in High
Definition Audio controller + Realtek ALC269Q-VC2-GR Codec
[6mm x 6mm @ MQFN48]
w/ class-D speaker amplifier(2W per channel @ 5V power
supply)
LPC I/O
Nuvoton NCT6102D [128-pin LQFP, 14 mm x 14mm x 1.4mm)
COM1 (RS232/422/485) [EXAR SP339EER1 232/422/485
transceiver for jumper-less]; COM2 (RS232 only) [SIPEX
SP3243EBER, QFN32]
[Hardware Monitor]
2 x Thermal inputs
2 x Voltage monitoring
1 x CPU Fan (PWM Fan type, 4-pin connector)
Digital IO
4 in & 4 out
iAMT(10.0)
For IB909AF-5650 / IB909AF-5350
Expansion Slots
1x mSATA/mPCIe(x1) w/ USB signal [Half-sized]
1x mSATA/mPCIe(x1) w/ USB signal [Full-sized]
Edge Connector
DVI-I x 1
RJ45 x2 for LAN#1 & #2
USB 3.0 stack connector x 1 for USB1 / 2 [Blue color]
DB9 x 1 for COM #1
Onboard
Header/Connector
DF20-20 socket connector x 2 for 24-bit dual channel LVDS
2 ports x SATA III [Blue color]
2x4 pins header x 1 for 2 USB 2.0 ports [DF11]
2x6 pins box header x1 for Audio [DF11]
1x4 pins box header x1 for Speaker out
2x5 pins box header x1 for COM2
2x5 pins headers x 1 for LPC (Debug purposes only)
5 pins box header x1 for smart battery
4 pins box header x1 for backlight/brightness control
4 pins power connector x1 for SATA HDD
2 pins power connector x1 for DC-in [180 degree vertical type]
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
Power Input
+9V ~ +24V DC-in
RoHS
Yes
Board Size
102mm x 147mm
OS supported
Windows 8 / Embedded; Windows 7 / Embedded Linux
Others
Heatsink
i-SMART (Auto-scheduler & Power fail resume function)
EEPROM 24C02(Reserved for designing, M-SO8 package)
IB909 User’s Manual 3

INTRODUCTION
Board Dimensions
4 IB909 User’s Manual

INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the IB909F in order to set up a workable system. The
topics covered are:
Installing the Memory ........................................................................... 6
Setting the Jumpers................................................................................ 7
Connectors on IB909F......................................................................... 11
IB909 User’s Manual 5

INSTALLATIONS
Installing the Memory
The IB909F board supports two DDR3L memory sockets for a
maximum total memory of 16GB DDR3L memory type.
Installing and Removing Memory Modules
To install the DDR3L modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3L module so that the key of the DDR3L module
aligned with that on the memory slot.
2. Gently push the DDR3L module in an upright position until the
clips of the slot close to hold the DDR3L module in place when the
DDR3L module touches the bottom of the slot.
3. To remove the DDR3L module, press the clips with both hands.
6 IB909 User’s Manual

INSTALLATIONS
Setting the Jumpers
Jumpers are used on IB909F to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB909F and their respective functions.
Jumper Locations on IB909F ................................................................ 8
J3: Clear CMOS Contents ..................................................................... 9
J4: Clear ME Contents........................................................................... 9
J7: Flash Descriptor Security Override (Factory use only) ................. 10
J9: LVDS Panel Power Selection........................................................ 10
IB909 User’s Manual 7

INSTALLATIONS
Jumper Locations on IB909F
Jumpers on IB909F.......................................................................... Page
J3: Clear CMOS Contents......................................................................9
J4: Clear ME Contents...........................................................................9
J9: LVDS Panel Power Selection ........................................................10
8 IB909 User’s Manual

INSTALLATIONS
J3: Clear CMOS Contents
J3 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed Clear CMOS
J4: Clear ME Contents
J4 Setting Function
Pin 1-2
Short/Closed Normal
Pin 2-3
Short/Closed
Clear ME
RTC
Register
3
1
3
1
IB909 User’s Manual 9

INSTALLATIONS
J7: Flash Descriptor Security Override (Factory use only)
J7
Flash Descriptor Security Override
Open Disabled (Default)
Close Enabled
J9: LVDS Panel Power Selection
J9 Setting Panel Voltage
Pin 1-2
Short/Closed 3.3V (default)
Pin 2-3
Short/Closed 5V
1
3
10 IB909 User’s Manual

INSTALLATIONS
Connectors on IB909F
Connector Locations on IB909F ......................................................... 12
CN3, CN4: Gigabit LAN..................................................................... 13
CN3: Intel® Clarkville I218V/I218LM GbE PHY ............................. 13
CN4: Intel® Pearsonville I211AT as 2nd GbE................................... 13
CN5: USB 1/2 Connector.................................................................... 13
CN6: VGA DVI-I Connector .............................................................. 13
CN7: DB9 Connector.......................................................................... 13
CN1, CN2: SATA Connectors ............................................................ 14
JP1: LCD Backlight Connector........................................................... 14
JP2: USB3/4 Connector....................................................................... 14
J2: Audio Connector (DF11 Connector) ............................................. 15
JP3, JP5: LVDS Connectors (LVDS1,LVDS2) .................................. 15
JP4: SPI Flash Connector (factory use only)....................................... 16
J5: Amplifier Connector...................................................................... 16
J7: Factory use only............................................................................. 16
JP6: SATA HDD Power Connectors................................................... 17
JP7: Debug 80 Port Connector (factory use only)............................... 17
J12: Smart Battery ............................................................................... 18
J13: Board Input Power Connector ..................................................... 18
J14: Front Panel Connector................................................................. 19
J15: Mini PCIE Connector (Supports mSATA).................................. 20
J16: Mini PCIE Connector (Half Size/ Supports mSATA)................. 20
J17: COM2/RS232 Serial Port ............................................................ 20
J19: Digital I/O Connector .................................................................. 21
CPU_FAN1: CPU Fan Power Connector........................................... 21
IB909 User’s Manual 11

INSTALLATIONS
Connector Locations on IB909F
12 IB909 User’s Manual

INSTALLATIONS
CN3, CN4: Gigabit LAN
CN3: Intel® Clarkville I218V/I218LM GbE PHY
CN4: Intel® Pearsonville I211AT as 2nd GbE
CN5: USB 1/2 Connector
CN6: VGA DVI-I Connector
CN7: DB9 Connector
(COM1) is a DB-9 connector.
Signal Name
Pin #
Pin #
Signal Name
DCD, Data carrier detect
1
6
DSR, Data set ready
RXD, Receive data
2
7
RTS, Request to send
TXD, Transmit data
3
8
CTS, Clear to send
DTR, Data terminal ready
4
9
RI, Ring indicator
GND, ground
5
10
Not Used
COM1 is jumper-less for RS-232, RS-422 and RS-485 and is to be
configured with BIOS Selection.
[
Pin #
Signal Name
RS-232
R2-422
RS-485
1
DCD
TX-
DATA-
2
RX
TX+
DATA+
3
TX
RX+
NC
4
DTR
RX-
NC
5
Ground
Ground
Ground
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC
10
NC
NC
NC
IB909 User’s Manual 13

INSTALLATIONS
CN1, CN2: SATA Connectors
JP1: LCD Backlight Connector
Pin #
Signal Name
1
+12V
2
Backlight Enable
3
Brightness Control
4
Ground
JP2: USB3/4 Connector
Signal Name
Pin #
Pin #
Signal Name
Vcc
1
2
Ground
D0-
3
4
D1+
D0+
5
6
D1-
Ground
7
8
Vcc
4 1
2 1
8 7
14 IB909 User’s Manual

INSTALLATIONS
J2: Audio Connector (DF11 Connector)
Signal Name
Pin #
Pin #
Signal Name
LINEOUT R
2
1
LINEOUT L
Ground
4
3
JD FRONT
LINEIN R
6
5
LINEIN L
Ground
8
7
JD LINEIN
MIC-R
10
9
MIC L
Ground
12
11
JD MIC1
JP3, JP5: LVDS Connectors (LVDS1, LVDS2)
The LVDS connectors (Hirose DF20G-20DP-1V) on board consist of
the first channel (LVDS1) and second channel (LVDS2).
Signal Name
Pin #
Pin #
Signal Name
TX0N
2
1
TX0P
Ground
4
3
Ground
TX1N
6
5
TX1P
Ground
8
7
Ground
TX2N
10
9
TX2P
Ground
12
11
Ground
CLKN
14
13
CLKP
Ground
16
15
Ground
TX3N
18
17
TX3P
Power
20
19
Power
1 11
2 12
2
20
1
19
IB909 User’s Manual 15

INSTALLATIONS
JP4: SPI Flash Connector (factory use only)
J5: Amplifier Connector
Pin #
Signal Name
1
OUTL+
2
OUTL-
3
OUTR-
4
OUTR+
J6, J8: DDR3L SO-DIMM Sockets
J7: Factory use only
9 10
1 2
1
4
1 2
16 IB909 User’s Manual