IBASE Technology IB919 Series User manual

IB919 Series
Intel
®
8
th
Gen. Core™
U-series / Celeron
®
SoC
3.5” Disk-Size SBC
User’s Manual
Version 1.0A
(March 2020)

ii IB919 Series User’s Manual
Copyright
© 2020 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval
system, translated into any language or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior
written consent of IBASE Technology, Inc. (hereinafter referred to as
“IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the
products described in this document without prior notice. Every effort has
been made to ensure the information in the document is correct; however,
IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising
from misapplication or inability to use the product or the information
contained herein, nor for any infringements of rights of third parties, which
may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for
identification purposes only and may be trademarks and/or registered
trademarks of their respective owners.

IB919 Series User’s Manual
iii
Compliance
This product has passed CE Class B tests for environmental specifications
and limits. This product is in accordance with the directives of the European
Union (EU). In a domestic environment, this product may cause radio
interference in which case users may be required to take adequate
measures.
This product has been tested and found to comply with the limits for a Class
B device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive of for waste
electrical and electronic equipment (WEEE - 2012/19/EU).
Instead, it should be disposed of by returning it to a
municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS
restrictions and prohibits use of the following substances
in concentrations exceeding 0.1% by weight (1000 ppm)
except for cadmium, limited to 0.01% by weight (100 ppm).
• Lead (Pb)
• Mercury (Hg)
• Cadmium (Cd)
• Hexavalent chromium (Cr6+)
• Polybrominated biphenyls (PBB)
• Polybrominated diphenyl ether (PBDE)

iv IB919 Series User’s Manual
Important Safety Information
Carefully read the precautions before using the board.
Environmental conditions:
•Use this product in environments with ambient temperatures between
0˚C and 60˚C.
•Do not leave this product in an environment where the storage
temperature may be below -20° C or above 80° C. To prevent from
damages, the product must be used in a controlled environment.
Care for your IBASE products:
•Before cleaning the PCB, unplug all cables and remove the battery.
•Clean the PCB with a circuit board cleaner or degreaser, or use cotton
swabs and alcohol.
•Vacuum the dust with a computer vacuum cleaner to prevent the fan
from being clogged.
WARNING
Attention during use:
•Do not use this product near water.
•Do not spill water or any other liquids on this product.
•Do not place heavy objects on the top of this product.
Anti-static precautions
•Wear an anti-static wrist strap to avoid electrostatic discharge.
•Place the PCB on an anti-static kit or mat.
•Hold the edges of PCB when handling.
•Touch the edges of non-metallic components of the product instead of
the surface of the PCB.
•Ground yourself by touching a grounded conductor or a grounded bit of
metal frequently to discharge any static.
CAUTION
There is danger of explosion if the internal lithium-ion battery is replaced by
an incorrect type. Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions or recycle them at a local recycling facility or
battery collection point.

IB919 Series User’s Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of
shipment cannot be ascertained, the product serial numbers can be
used to determine the approximate shipping date.
•3
rd
-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are
not manufactured by IBASE, such as CPU, CPU cooler, memory,
storage devices, power adapter, panel and touchscreen.
＊ PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE
BILLED FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest
information about the product.
2. If you need any further assistance from your distributor or sales
representative, prepare the following information of your product and
elaborate upon the problem.
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the
version numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the
form and contact your distributor or sales representative.

vi IB919 Series User’s Manual
Table of Contents
Chapter 1 General Information ............................................. 1
1.1 Introduction .........................................................................................2
1.2 Features..............................................................................................2
1.3 Packing List......................................................................................... 3
1.4 Optional Accessories...........................................................................3
1.5 Specifications ...................................................................................... 4
1.6 Block Diagram..................................................................................... 6
1.7 Overview .............................................................................................7
1.8 Dimensions ......................................................................................... 9
Chapter 2 Hardware Configuration........................................ 11
2.1 Essential Installations Before You Begin ........................................... 12
2.1.1 Installing the Memory ........................................................... 12
2.2 Setting the Jumpers .......................................................................... 13
2.3 Jumper & Connector Locations ......................................................... 14
2.4 Jumpers Quick Reference ................................................................. 15
2.4.1 CMOS Data Clearance (JBAT1).......................................... 15
2.4.2 EDP Panel Power Selections (JP2)..................................... 16
2.4.3 LVDS Panel Power / Brightness Selections (JP3 / JP5) ...... 16
2.4.4 EDP / LVDS Selections (JP4) ............................................. 17
2.5 Connectors Quick Reference............................................................. 18
2.5.1 COM1 RS-232/422/485 Port (CN9) ..................................... 19
2.5.2 Amplify Connector (J1)........................................................ 20
2.5.3 Audio Connector (J3) .......................................................... 20
2.5.4 SATA HDD Power Connector (J5)....................................... 21
2.5.5 SMBUS Connector (J10) ..................................................... 21
2.5.6 Front Panel Connector (J9) ................................................. 22
2.5.7 USB 2.0 Connector (J6) ...................................................... 23
2.5.8 Battery Connector (J16) ...................................................... 23
2.5.9 COM2, COM3, COM4 RS-232 Ports (J20, J21, J22)........... 24
2.5.10 DC Power Input Connector (J18)......................................... 24
2.5.11 Digital I/O Connector (J17) .................................................. 25
2.5.12 LCD Backlight Connector (J15) ........................................... 25
2.5.13 LVDS Connector (J14, J13)................................................. 26
2.5.14 CPU Fan Connector (CPU_FAN1) ...................................... 26

IB919 Series User’s Manual
vii
Chapter 3 Drivers Installation ............................................. 27
3.1 Introduction........................................................................................28
3.2 Intel
®
Chipset Software Installation Utility ..........................................28
3.3 VGA Driver Installation.......................................................................30
3.4 HD Audio Driver Installation ...............................................................32
3.5 LAN Driver Installation .......................................................................34
3.6 Intel
®
Management Engine Drivers Installation ..................................36
3.7 Intel
®
Serial IO Drivers Installation .....................................................38
Chapter 4 BIOS Setup.......................................................... 41
4.1 Introduction........................................................................................42
4.2 BIOS Setup........................................................................................42
4.3 Main Settings.....................................................................................43
4.4 Advanced Settings.............................................................................44
4.4.1 Connectivity Configuration ....................................................45
4.4.2 CPU Configuration................................................................46
4.4.3 Power & Performance...........................................................47
4.4.4 PCH-FW Configuration.........................................................48
4.4.5 Trusted Computing ...............................................................49
4.4.6 ACPI Settings .......................................................................50
4.4.7 LVDS Configuration..............................................................51
4.4.8 F81964 Super IO Configuration ............................................52
4.4.9 F81964 Super IO Configuration for IB919EF ........................53
4.4.10 Hardware Monitor .................................................................54
4.4.11 AMI Graphic Output Protocol Policy......................................55
4.4.12 USB Configuration................................................................56
4.4.13 CSM Configuration ...............................................................57
4.4.14 NVMe Configuration .............................................................58
4.4.15 Network Stack Configuration ................................................59
4.5 Chipset Settings ................................................................................60
4.6 Security Settings................................................................................65
4.7 Boot Settings .....................................................................................66
4.8 Save & Exit Settings ..........................................................................67

viii IB919 Series User’s Manual
Appendix ........................................................................................ 68
A. I/O Port Address Map........................................................................ 69
B. Interrupt Request Lines (IRQ)............................................................ 72
C. Watchdog Timer Configuration.......................................................... 74
D. Onboard Connector Reference Types ............................................... 78

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Optional Accessories
•Specifications
•Block Diagram
•Board Overview
•Board Dimensions

2 IB919 Series
User’s Manual
1.1 Introduction
•IB919 series is a 3.5” disk-size single board computer based on the
platform of Intel®8th Gen. Core™U-series or Celeron®processor. It
features both HDMI and Display Port at I/O coastline, and onboard
headers for dual channel LVDS interface for video display. Advanced
features include four USB 3.0, two SATA III, configurable watchdog
timer, digital I/O, and TPM 2.0.
Photo of IB919
1.2 Features
•3.5” disk-size SBC with Intel®8th Gen. Core™ U-series or Celeron®
processor
•2 x DDR4-2400/2133 SO-DIMM slots, expandable up to 32 GB
•Video output through LVDS or EDP connector, Display Port, and USB
Type C
•2 x GbE LAN ports, 2 x USB 2.0, 4 x USB 3.0, 4 x COM, 2 x SATA III,
1 x M.2 (M-Key), 1 x M.2 (E-Key)
•Configurable watchdog timer, digital I/O, TPM 2.0

General Information
IB919 Series User’s Manual 3
1
1.3 Packing List
Your IB919 package should include the items listed below. If any of the items
below is missing, contact the distributor or dealer from whom you purchased
the product.
•IB919 SBC x 1
•Disk x 1
(including chipset drivers and flash memory utility)
•This User’s Manual x 1
1.4 Optional Accessories
IBASE provides optional accessories as follows. Please contact us or your
dealer if you need any.
•Cable Kit (IB76A-1)
Including:
DC-In power cable (PW87) x 1
COM ports cable (PK1H) x 1
SATA & HDD power cable (SATA-53A) x 1
USB 2.0 cable (USB29) x 1
•Audio cable (Audio-18)
•Heat spreader (HSIB919-A)

4 IB919 Series
User’s Manual
1.5 Specifications
Product
Name
IB919AF-
8665
IB919AF-
8365
IB919EF-
8145
IB919EF-
4305
Form Factor
3.5” disk-size SBC
System
Operating
System
•Windows 10
•Linux Ubuntu / Fedora
CPU Type
Intel®8th
Gen. Core™
i7-8665UE
Intel®8th
Gen. Core™
i5-8365UE
Intel®8th
Gen. Core™
i3-8145UE
Intel®
Celeron®
4305UE
CPU Speed 1.7 GHz /
4.4 GHz
1.6 GHz /
4.1 GHz
2.2 GHz /
3.9 GHz
2.0 GHz
Cache 8MB, 6MB, 4MB, 2MB
Chipset Integrated in Intel®U-series processor
Memory 2 x DDR4-2400/2133 SO-DIMM, expandable up to 32 GB
(Non-ECC)
Storage M.2 socket x 1(M-Key, type 2280) SSD
Graphics Intel®8th Gen. Core™U-series integrated graphics
Network Intel®I219LM & I211AT Intel®I219V & I211AT
Super I/O Fintek F81964D-I
Audio Codec
& Controller
Intel®U-series processor built-in HD audio controller
Realtek ALC269Q codec
Power
Requirement
9 ~ 24V DC-In
iAMT 12.X N/A
USB Type C USB 3.1 (Gen.2)
TPM 2.0
RAID Yes
Watchdog
Timer Yes (256 segments, 0, 1, 2…255 sec / min)

General Information
IB919 Series User’s Manual
5
1
BIOS AMI BIOS
H/W Monitor
Yes
Dimensions 102.22 x 147.01 mm (4.02” x 5.8”)
RoHS Yes
Certification
CE, FCC Class B
I/O Ports
Display
•1 x USB Type C (DisplayPort 1.2) 3840 x 2160 at 60Hz
•1 x DisplayPort (1.2) 3840 x 2160 at 60 Hz
•1 x dual-channel LVDS,1920 x 1080 at 60 Hz or EDP
(1.4) 4096 x 2304 at 60 Hz
LAN 2 x RJ45 GbE LAN
USB •4 x USB 3.1: I/O coastline connectors
•2 x USB 2.0: via an on-board pin headers
Serial
4 x COM ports:
•COM1: RS-232/422/485 (I/O coastline DB9
connector, jumper-less selection)
•COM2, COM3, COM4: RS-232 only (via on-board
box-headers)
SATA 2 x SATA III
Audio On-board audio connector for Line-In, Line-Out, and
Mic-In
Digital IO 4-In & 4-Out
Expansion
Slots
M.2 socket x 1(M-Key, type 2280),
M.2 socket x 1(E-Key, type 2230)
Environment
Temperature
•Operation: 0 ~ 60 °C (32 ~ 140 °F)
•Storage: -20 ~ 80 °C (-4 ~ 176 °F)
Relative
Humidity 0 ~ 90 %, non-condensing at 60 °C
All specifications are subject to change without prior notice.

6 IB919 Series
User’s Manual
1.6 Block Diagram

General Information
IB919 Series User’s Manual
7
1
1.7 Overview
Top View
Bottom View
Photos of IB919
＊The photos above are for reference only. Some minor components may
differ.

8 IB919 Series
User’s Manual
I/O View
No. Name No. Name
1 COM1 RS-232/422/485 Port 4 Display Port
2 USB 3.0 Ports 5 USB Type-C
3 LAN Port

General Information
IB919 Series User’s Manual 9
1
1.8 Dimensions

10 IB919 Series
User’s Manual
This page is intentionally left blank.

11
Chapter 2
Hardware Configuration
This section provides information on jumper settings and
connectors on the IB919 in order to set up a workable system.
On top of that, you will also need to install crucial pieces such as
the CPU and the memory before using the product. The topics
covered are:
•Essential installations before you begin
•Jumper and connector locations
•Jumper settings and information of connectors

12 IB919 Series
User’s Manual
2.1 Essential Installations Before You Begin
Follow the instructions below to install the memory.
2.1.1 Installing the Memory
The IB919 series supports two DDR4 memory sockets for a maximum total
memory of 32 GB. To install the modules, locate the memory slot on the
board and perform the following steps:
1. Align the key of the memory module with that on the memory slot and
insert the module slantwise.
2. Gently push the module in an upright position until the clips of the slot
close to hold the module in place when the module touches the bottom
of the slot.
To remove the module, press the clips outwards with both hands, and the
module will pop-up.